View Full Version : is there tips on cleaning head studs thread in block
davidpham
05-03-2013, 02:49 AM
is there a tips where i could clean the head studs out because when i reinstall arp head studs none of them lines up
jr_ss
05-03-2013, 05:51 AM
Take an old stud/bolt and cut a decent size groove on one side. Clean it up so there are no burrs and run it down the threads. You can also use the correct tap to clean the threads up as well.
davidpham
05-03-2013, 06:35 AM
Take an old stud/bolt and cut a decent size groove on one side. Clean it up so there are no burrs and run it down the threads. You can also use the correct tap to clean the threads up as well.
like just torque the oem bolt down right?
zombiewolf513
05-03-2013, 06:45 AM
No, the cut you made vertically on the threads of the bolt will be an area to collect junk from the threads in the block, you dont torque it down
VNG704
05-03-2013, 08:28 AM
Use a tap. What they're saying is, you can make one with an old head bolt. You thread it in only, no torque. Make sure the threaded holes are clean afterwards.
dawagarage
05-03-2013, 09:39 AM
go to a parts store and borrow a "thread repair set,"
itll have the tap you need. (m10x1.5 i think?) i borrowed mine from oreilly.
there is a deposit but once you return it you get your money back.
that or make your own tap like previously mentioned.
after that, if you have a pressure washer you can hit the hole with that and after that if you have pressurized air you can use that to get all the water out of there.
jr_ss
05-03-2013, 10:13 AM
I sprayed my holes out with brake clean to remove any oily deposits. Then I used compressed air and hit each one with that as well. All that was in preperation for a fresh/clean slate for my ARP lube...
zombiewolf513
05-03-2013, 10:46 AM
I sprayed my holes out with brake clean to remove any oily deposits. Then I used compressed air and hit each one with that as well. All that was in preperation for a fresh/clean slate for my ARP lube...
I did the exact same
davidpham
05-03-2013, 11:33 AM
im like using brake cleaner and pipe cleaner i dont have air compressor =[
zombiewolf513
05-03-2013, 12:06 PM
Cans of Keyboard/air duster
davidpham
05-03-2013, 07:26 PM
oem bolt goes straight in up and down and arp studs doesnt? lame.....
VNG704
05-04-2013, 08:05 AM
Are the arp studs new/correct ones? Are the threads on those clean/straight? Maybe you can try to run them through a die.
jr_ss
05-04-2013, 08:18 AM
The ARPs do not bottom out in the hole. They are not long enough for that unless you've bought the ARP/Mazworx spec items. Hand tighten them into the block you can use the Allen key to help, but do not put any torque on them.
davidpham
05-04-2013, 11:57 PM
is it okay if the studs is little bit taller or shorter than others? theyre not perfectly 100% even
jr_ss
05-05-2013, 09:17 AM
Two of them are taller if I can remember correctly. I would try to get them even, but I'm OCD like that
cotbu
05-05-2013, 09:33 AM
With the head off and studs in, it looked like the front six where higher than the rear four, or vice versa.
When the head gasket, and head was fitted, and studs reinstalled, they all appeared to protrude the same amount. Even after final torquing they all are identical in remaining thread height. 20, 40, 60, 80, 80 ARP lube
shift_down
05-05-2013, 11:03 AM
Cut a slit in old bolt:
http://i1101.photobucket.com/albums/g438/ramyswar/IMAG0018_zps1d123903.jpg
Spray carb cleaner down the holes in the block.
Thread the slotted bolt in each hole.
Repeat process 3 times, then spray with compressed air to dry it all out.
That's what I did.
davidpham
05-31-2013, 02:56 PM
https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-prn2/181224_4921579166856_1891887365_n.jpg
Still stress out about this..
jr_ss
05-31-2013, 03:29 PM
That's normal... I just couldn't remember what two sat taller in the block.
davidpham
05-31-2013, 03:43 PM
Two middle are tall and the one next to the guide is alittle tall, the rest is like almost exact same heights. still work right?
jr_ss
05-31-2013, 05:08 PM
Yeah, check the one sitting higher than the rest that aren't in the middle. The middle ones will be higher.
davidpham
05-31-2013, 06:06 PM
I think it should be fine, i put the head on just to measure the threads they all seems to be fine and should be torque down the same way. I'll see wsp after i assemble everything together
vBulletin® v3.8.11, Copyright ©2000-2021, vBulletin Solutions Inc.