Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 12-07-2015, 09:12 AM   #1
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
glowing turbo

Hey guys. I am new to the S chassis. Always liked them and until recently never been able to afford one. Found a guy through a friend with an SR swapped 92 coupe. Coilovers, open downpipe, good bit of front suspension work, aftermarket radiator, bov, coolant reservoir, and some other odds and ends. The car came with a turbo elbow I have yet to install and it came with a Freddy intake. When deciding to purchase it, previous owner stated he had an issue that after 30 minutes or so the car would run hot. He did head gaskets, studs, and a bunch of other stuff trying to fix it and thought it was the turbo. I towed it home and found some clamps look but no significant leaks. Day after thanksgiving I was driving to work and all of a sudden I see the temp gauge rising. First time in a month of owning it. Turns out one of the hoses under the intake busted. Pulled intake, replaced hoses, and decided now would be the time to install the Freddy intake. All installed with a IACV relocation kit and having a few issues. First being idle concerns which I have to still do some work on. I changed the oil to confirm it wasnt milky. Took car for a quick spin. Ran good. Spooled nicely. Next thing I know I'm seeing smoke from under the hood and the exhaust. Thought there was some oil spraying up from under the hood onto the windshield and hit the wipers. Leaned up in the seat at the same time and realized I had a fire under the hood. Quickly pulled over, shut the car off and popped the hood. Manifold and turbo were GLOWING red. With the smoke I seen I am thinking I have blown a turbo seal and the oil got into the center housing causing the turbo to get hot. This would explain the smoke and the glowing. The fire started because the manifold wrap the previous owner installed couldn't withstand the heat.


Basically my question is if a bad oil seal would be the cause of what I experienced. I do not have much S chassis experience, mostly Z chassis.

Any and all help would be appreciated.

Thank you in advance.
drb5721 is offline   Reply With Quote
Sponsored Links
Old 12-07-2015, 01:40 PM   #2
ultimateirving
Zilvia FREAK!
 
ultimateirving's Avatar
 
Join Date: Nov 2010
Location: arizona
Age: 33
Posts: 1,519
Trader Rating: (1)
ultimateirving is an unknown quantity at this point
Feedback Score: 1 reviews
Wow that's crazy. Is this a stock sr? Stock tune too?
__________________
Z32 with lq4 swap
Desert Street Scene || Dssevents.com
ultimateirving is offline   Reply With Quote
Old 12-07-2015, 01:44 PM   #3
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
From all I can tell it is. I do not see anything beyond the normal additions of downpipe, CAI, FMIC, tubular manifold, and now the Freddy intake.
drb5721 is offline   Reply With Quote
Old 12-07-2015, 02:00 PM   #4
EnnEssEnnKAT
Zilvia Junkie
 
EnnEssEnnKAT's Avatar
 
Join Date: Sep 2014
Location: New Hampshire
Posts: 427
Trader Rating: (13)
EnnEssEnnKAT can only hope to improve
Feedback Score: 13 reviews
The glowing red is probably caused by the exhaust gases. That's about the only thing in the engine bay that will get something red hot. My best guess is that you're running lean, either because of a weak fuel pump, bad regulator, or busted mass air flow. Could also be timing is off, something along those lines. A lean condition would create that intense red-hot heat.
EnnEssEnnKAT is offline   Reply With Quote
Old 12-07-2015, 02:04 PM   #5
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
I just didn't think that simply swapping a greddy style intake would cause this issue. I have yet to read an installation that stated anything with having to check timing etc when swapping the manifolds. Car never did this prior to the coolant hose busting.
drb5721 is offline   Reply With Quote
Old 12-07-2015, 03:09 PM   #6
FeArZ
Leaky Injector
 
FeArZ's Avatar
 
Join Date: Aug 2013
Location: Houston, TX
Age: 28
Posts: 79
Trader Rating: (4)
FeArZ is an unknown quantity at this point
Feedback Score: 4 reviews
More air = more fuel. I don't see any mention of changing injectors or tuning.

The car needs a tune also. Do you have a wideband? This is vital to understanding what is going on with the engine. It would help eliminate some factors so you can narrow it down.
FeArZ is offline   Reply With Quote
Old 12-07-2015, 03:21 PM   #7
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
I have a gauge but no sensor. Came in the car like so. The reason I am thinking I have a blown oil seal in the turbo is the grey smoke I am burning when I drove it. Turbo spools fine. But there is a huge trail of smoke behind the car. It does it at all times now. Car runs great, just smokes like crazy. I looked at the exhaust where the elbow meets the downpipe and realized there is a small leak there and after the exhaust starts to get hot, I get smoke from there that smells like oil.
drb5721 is offline   Reply With Quote
Old 12-07-2015, 03:55 PM   #8
Green Arrow
BANNED
 
Join Date: Dec 2015
Location: North Korea
Posts: 349
Trader Rating: (0)
Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow
Feedback Score: 0 reviews
Sounds like a timing issue, also do you have a afr gauge?
Green Arrow is offline   Reply With Quote
Old 12-07-2015, 04:02 PM   #9
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
Timing still does not explain the oil burning. If I blew an oil seal, oil could be getting in the exhaust housing and getting hot.
drb5721 is offline   Reply With Quote
Old 12-07-2015, 04:05 PM   #10
Green Arrow
BANNED
 
Join Date: Dec 2015
Location: North Korea
Posts: 349
Trader Rating: (0)
Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow
Feedback Score: 0 reviews
Given you don't know if the block has 120k miles or 20k miles....it could be rings or it could be a pinhole in the oil return... If the spark is coming late it could be combusting in the turbo
Green Arrow is offline   Reply With Quote
Old 12-07-2015, 06:00 PM   #11
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,646
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
If you glow a manifold, your timing is wrong, or you are making way more power than you have fuel for. Fuel cools of the exhaust (EGT) so does water injection, ethanol, methanol. But you are on straight gasoline right? So the EGT is skyrocketing either because you ran the engine hard (make power) without enough fuel (cooling), OR, Your timing is retarded and pushing heat to the exhaust system. The oil may be related somehow but it is mostly likely a result OF your high EGT and not the cause.

Steps I would take

0. compression test the engine to make sure a piston hasnt broken into pieces, allowing blow-by to push oil out of the engine
1: make sure you have enough fuel for the power you are making, i.e. Watch the wideband.

2. Set the ignition timing properly, use the FSM or find one of my many posts where I explain how I do it
3. Replace the ECU/CAS if the wideband says a good number (11:1 or 12:1 for example) and the ignition timing appears right, and the compression test is good. Alternatively you can diagnose each cylinder individually for a timing problem. I have seen this happen on a POwer FC, after 30 minutes of hot run time, suddenly one or two cylinders would glow red, the ECU was bad.
Kingtal0n is offline   Reply With Quote
Old 12-07-2015, 07:25 PM   #12
EnnEssEnnKAT
Zilvia Junkie
 
EnnEssEnnKAT's Avatar
 
Join Date: Sep 2014
Location: New Hampshire
Posts: 427
Trader Rating: (13)
EnnEssEnnKAT can only hope to improve
Feedback Score: 13 reviews
Quote:
Originally Posted by drb5721 View Post
Timing still does not explain the oil burning. If I blew an oil seal, oil could be getting in the exhaust housing and getting hot.


Could have melted the seals, when it went red hot. I'm not sure what it is but I'd get that af sensor and a turbo rebuild, and go that route.
EnnEssEnnKAT is offline   Reply With Quote
Old 12-07-2015, 09:07 PM   #13
Green Arrow
BANNED
 
Join Date: Dec 2015
Location: North Korea
Posts: 349
Trader Rating: (0)
Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow Green Arrow
Feedback Score: 0 reviews
exactly, timing is a big variable for turbo motors; it highlights the problem.
Green Arrow is offline   Reply With Quote
Old 12-07-2015, 09:12 PM   #14
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
The oil burning and smoke started on first startup post coolant repair and manifold swap. Will check timing. Compression shouldnt be an issue as the engine runs extremely smooth all the way throughout the RPM range. I initially thought my issue was the loose clamp on the oil return. Again however, the oil burning was there before driving the car. Had a friend at work today check the shaft play in the turbo since its my day off, and he says its got a good amount of play, so rebuild/replacement was inevitable . Will see if i have a bung I can install a wideband sensor in. Will check compression.
drb5721 is offline   Reply With Quote
Old 12-07-2015, 09:45 PM   #15
[email protected]
Nissanaholic!
 
Join Date: Jul 2008
Location: Zacatecas, Mx; Paramount, Ca
Age: 31
Posts: 1,626
Trader Rating: (32)
R@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymoreR@ddy is not welcome here anymore
Feedback Score: 32 reviews
too much timing OR running lean. tune the fucking thing.
R@ddy is offline   Reply With Quote
Old 12-08-2015, 01:58 AM   #16
Croustibat
Nissanaholic!
 
Join Date: Aug 2011
Location: France - Toulouse
Age: 41
Posts: 1,851
Trader Rating: (0)
Croustibat is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by FeArZ View Post
More air = more fuel. I don't see any mention of changing injectors or tuning.
That is all great and good, but turbo engines don't run alphaN EMS, so you are wrong.

Quote:
Originally Posted by FeArZ View Post
The car needs a tune also. Do you have a wideband? This is vital to understanding what is going on with the engine. It would help eliminate some factors so you can narrow it down.
His timing is way too retarded, no need for a wideband there. Turbo glowing at this points means the CAS is way off. If there is a lack of fuel problem, it does not come from the tune, but from a fuel delivery problem.

Anyway you are right on the car needing a tune, but it has nothing to do with fueling, and it needs to be sorted BEFORE getting tuned.
Croustibat is offline   Reply With Quote
Old 12-08-2015, 07:04 AM   #17
drb5721
Leaky Injector
 
Join Date: Dec 2015
Location: nc
Age: 30
Posts: 77
Trader Rating: (1)
drb5721 is an unknown quantity at this point
Feedback Score: 1 reviews
Never had an issue until after this hose ruptured. Replaced and swapped intakes per every write up available. Nothing anywhere states anything about needing to tune, change timing, fuel, or anything. None of that was messed with. No sensors were changed. Fuel system is the same with no change other than being put on another manifold. CAS was only unplugged to allow removal of the manifold. Again, compression will be tested even though the car runs entirely too smooth for me to think there is an issue there.
drb5721 is offline   Reply With Quote
Old 12-08-2015, 07:46 AM   #18
EnnEssEnnKAT
Zilvia Junkie
 
EnnEssEnnKAT's Avatar
 
Join Date: Sep 2014
Location: New Hampshire
Posts: 427
Trader Rating: (13)
EnnEssEnnKAT can only hope to improve
Feedback Score: 13 reviews
Quote:
Originally Posted by drb5721 View Post
Never had an issue until after this hose ruptured. Replaced and swapped intakes per every write up available. Nothing anywhere states anything about needing to tune, change timing, fuel, or anything. None of that was messed with. No sensors were changed. Fuel system is the same with no change other than being put on another manifold. CAS was only unplugged to allow removal of the manifold. Again, compression will be tested even though the car runs entirely too smooth for me to think there is an issue there.
I see what you mean, you basically didn't touch anything except the air intake. Not needing a tune is YMMV, really.. Before the intake, there was no turbo glowing. After the intake install, the turbo was red hot. Sounds too coincidential but my guess is something else went haywire.
EnnEssEnnKAT is offline   Reply With Quote
Old 12-08-2015, 07:49 AM   #19
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,646
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
You need a wideband. Nobody runs even the cheapest $2 redtop without a wideband. It doesnt make any sense and would prevent 98% of this posting. Guessing that the compression is good by the way it drives is also a mistake- even if it is good, you still want to be taking a measurement, and writing it down, at least once per year.
Kingtal0n is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:43 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™