S13 -> FC Fun in the Sun ~Street Style~

[LaMaR-]

Hey everyone, I'm far from new here but its my first time throwing a build thread on the site. I figured there are a lot of people in drifting and clean simple cars so why not share what I've been up to. If this isn't aloud please feel free to send me a message or leave a comment and I will be sure to remove the thread.

I've been into drifting for a few years now and have built a couple different cars including this S13 that I sold a couple years ago and I am now building my most recent FC RX7. The RX7 is a car that I can't get enough of and the one below is actually my 5th one and will be my most modified one to date.

Drivetrain
SR20DET Swap
Greddy FMIC
Koyo Radiator
HKS BOV
Megan Racing 3" Exhaust
S14 Welded Rear Diff

Suspension
Tein Super Drift Coilovers
PBM Solid Rack Bushings
Isis solid subframe bushings
Isis adjustable arm kit
Circuit sports rucas

Interior
Bucket Seats with Harnesses
Momo Steering wheel with hub
Greddy Boost Controller
HKS Turbo Timer
Greddy Boost Gauge
AEM Air Fuel Gauge
Oil Pressure Gauge
Volt Gauge

Exterior
17" XXR 962's

I bought this car August 17th, 2012 looking like this.
http://i18.photobucket.com/albums/b116/StolenSol93/234.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/1_zpsa2565cdf.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/2_zps37abf568.jpg

The car ran like poo, had massive 18" rims and "lowering" springs. This thing was a monster truck. Well I got the car home that night put it in the garage and immediatly left for Daytona to purchase a used set of Tein SuperDrift coilovers for a good price.

http://i18.photobucket.com/albums/b116/StolenSol93/123.jpg

I waited a few days to install the coilovers since I was still looking for wheels and a welded differential. Three days layer August 20th, I drove to Georgia to get them. 17" XXR 962. Yes I know not baller wheels but alot better then those 18's that were previously on the car. The Differential is out of a S14 which I didnt realize till I got home. The next day I had to go order the longer diff bolts and a set of bushings from Nissan. Not a bad deal since they overnighted them for me.

http://i18.photobucket.com/albums/b116/StolenSol93/2-3.jpg

The install of the parts happened a couple days later and the outcome was this. Alignments way off and I still want to adjust the height a bit.

http://i18.photobucket.com/albums/b116/StolenSol93/yum.jpg

Brought the front end down a little more but I still want it lower. It handles really well and slides very easy but still doesnt look right yet. Sorry I dont have any photos of it going sideways. Soon though
http://i18.photobucket.com/albums/b116/StolenSol93/P8257939.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P8257947.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P8257955.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P8257965.jpg

The last picture shows no cage in the car or harness bar. That is the plan but havnt had time or money to order one so its going to have to wait. I do realize the dangers of not having one during a accident when using harnesses and I am doing this at my own risk.

At some point i picked up a used Momo steering wheel and hub since the stock one was disgusting and beat to shit. Sorry for the iphone photo
http://i18.photobucket.com/albums/b116/StolenSol93/Interior.jpg

At this point I had been driving the car around for a few weeks and was tired of the horrible alignment so I decided it was time to order more suspension pieces.
I went with the Isis arm kit from Enjuku along with solid rear subframe bushings and PoweredByMax solid rack bushings. This should stiffen it up alot and give me a good alignment.

http://i18.photobucket.com/albums/b116/StolenSol93/suspension.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/alldone-1.jpg

Taking out the rear subframe for the first time by yourself is a pain. I will never attempt this again its deff alot easier with two people.
http://i18.photobucket.com/albums/b116/StolenSol93/pbm.jpg

September sometime is when all the suspension went in, I finally get the subframe back into the car and go to bolt my coilovers in and I cant get them to fit. They dont fit with the RUCAs that I ordered. Luckly Enjuku is a good company and allowed me to return them and get Circuit sports. Thanks Enjuku. The car was off the road for atleast a week but with all the new suspension pieces it was a blast to drive.

Next came more interior. I dont have any great photos of it installed yet but I will get some soon. I got tired of the stock 90's grey cloth and wanted something nicer/cleaner. I found this material at Joanns fabric and it worked awesome
http://i18.photobucket.com/albums/b116/StolenSol93/doorpanel.jpg

Here are those shots from today unedited cause im no photographer although I do want to learn..
http://i18.photobucket.com/albums/b116/StolenSol93/PA148649_zps0ba3c0f4.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/PA148658_zps2f4a0a75.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/PA148663_zps81dbca7e.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/PA148672_zpsb9e8497b.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/PA148673_zpsefffad08.jpg

Well the headgasket blew in the KA and its been sitting for a few weeks but I picked my self up a killer Black friday deal...

SR20DET swap
http://i18.photobucket.com/albums/b116/StolenSol93/PB258681.jpg

We are pulling the ka and cleaning my bay this week and then saturday we should be pulling the sr and putting it in my hatch... December 15th is my first legitimate drift event so I will have some sideways photos/videos then

For the second part of this update the SR swap is complete and running amazing. My buddy Brandon and I pulled the KA in the middle of the week and then saturday we decided to pull everything from the black car and put it into my red hatch.
http://i82.photobucket.com/albums/j259/sprinter1/IMAG0210.jpg

Pulling:
http://i82.photobucket.com/albums/j259/sprinter1/IMAG0211.jpg

Out:
http://i82.photobucket.com/albums/j259/sprinter1/IMAG0212.jpg

Although we did run into a issue with it running properly. It would start but barely idle and when you stepped on the gas it wouldnt go at all. Anything past 1/8th throttle would kill it. After trouble shooting for a couple hours I gave up and came back to it sunday. Im not sure what it was but I ended up checking the fuel pump in my car and the black car. Mine was stock and the black car has a walbro 255 in it. Swapped them quick and bam it ran like a beast. Although I dont have any photos of the initial swap I do have these. This past weekend I started a wire tuck so that I could prepare to tub my front end. The last photo shows one reason that I want to tub this car lol.
http://i18.photobucket.com/albums/b116/StolenSol93/P1018748.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P1018752.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P1018754.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/P1018755.jpg

Bought these wheels as drift spares.. Cant wait for the 16th
http://i18.photobucket.com/albums/b116/StolenSol93/307614_10151343224032888_244237620_n.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/227718_10151343224407888_1140997118_n.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/543229_10151344373697888_1164078644_n.jpg

[LaMaR-]

Not long after that last photo I ended up separating from my wife. A girl I had been dating since high school and whom I had married when I joined the military. Im not sure what it was that ended our relationship but she left and I sold the car. Selling that car is the one thing that I wish I never would have done. Something in my mind told me that if I sold the car, she would stay. I was wrong. She left and drained my bank accounts at the same time... A true fresh start?

Nearly a year after her leaving I saved up enough money to buy another project. I ended up driving to North Carolina and back and picking up another RX7. Why North Carolina? Reason being is for the price I paid, I got a heck of a deal. Its a 88 FC3S RX-7 with Tein Super Drift coilovers, the same coils I had in my s13, it also has a ford 5.0 swap with T-5 trans and the full grannys swap kit. The motor has some work done to it most of which I have no idea what lol. As far as I currently know it has after market heads, cams, its chipped, headers, arp headstuds, and a whole bunch more internally probably. Here it is when I picked it up.

http://i18.photobucket.com/albums/b116/StolenSol93/null_zps409f6778.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps8f072f05.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps74937f19.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps74937f19.jpg.html)

Upon getting her home I immediately decided I needed to figure out why it was running so poorly and that I needed to put my touch on the car for sure.

In the garage doing what I always do lol take the front end off and have a look at everything else http://i18.photobucket.com/albums/b116/StolenSol93/null_zps0faa1511.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps0faa1511.jpg.html)

The engine bay was and is still a mess, I can't wait to pull the motor after the september drift event and start cleaning up the wiring harness and the engine bay itself. The interior wiring on the car is even more of a mess, heres what it looked like under the dash :evil: http://i18.photobucket.com/albums/b116/StolenSol93/null_zps515f8e25.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps515f8e25.jpg.html)

At this point I started ordering parts to make it a better platform to drive around
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps5957e00d.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps5957e00d.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps58051921.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps58051921.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps317fa40a.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps317fa40a.jpg.html)

Grip Royal Royal Knight
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps966c3517.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps966c3517.jpg.html)

NRG Hub and Quick Release
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsfb267c7c.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsfb267c7c.jpg.html)

Crow Harnesses
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps1fc1df0a.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps1fc1df0a.jpg.html)

Bride LowMax Replica seats
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsa3d0774c.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsa3d0774c.jpg.html)

After this it was time for its first street legal drive.. Everyone loves gas station pictures right?
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps022a303d.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps022a303d.jpg.html)

It was running a little better still has vacuum leaks and whatever else going on but overall I am super happy with the way it runs and drives. Interior was together and I could drive it legally so I went to my first drift event as a driver. I learned a bunch and enjoyed the car, I just wish that I had swapped my rear tires earlier and not missed my competition run.
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsaf0fb424.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsaf0fb424.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps848c1d8a.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps848c1d8a.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpscfb55668.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpscfb55668.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps701f15e1.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps701f15e1.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsce8800ae.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsce8800ae.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps261176a1.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps261176a1.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps43a019ce.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps43a019ce.jpg.html)

During the event I noticed that my rear differential was still leaking even though I had just replaced the pinion seal, and also Brandon noticed some smoke from my engine bay when I met him at the gas station to head to the event. My slave cylinder was leaking right on my exhaust and would burst into flames for just a second so we had a extinguisher ready the whole day just in case.

After this event I decided I had to do something to fix the rear suspension, the FC doesnt have a real camber adjustment stock and at the time there were very few options to fix the camber. Not a week later Drew decided to take me in a PBM thread stating that the camber links, toe arms, and Camber arm would be coming out. I ordered them as soon as they were put up for sale along with the solid Differential mount and bushings, and the solid subframe bushings. Heres some pictures of the rebuild of the rear suspension, As I was rebuilding I took my differential to a shop here on the westside to have them fix the leak and check over the internals.

Toe Arms Left, Camber Arm center, Camber links right
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps30a9c60c.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps30a9c60c.jpg.html)

Diff bushings top, subframe bushings bottom in my freezer
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps39e5cd36.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps39e5cd36.jpg.html)

It was now time to pull the rear suspension, you might want to scroll slowly because its really ugly..
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsb144a896.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsb144a896.jpg.html)

First things first start to dismantle it all
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps7fdf68f9.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps7fdf68f9.jpg.html)

Broken forward Diff mount, and rear bushings are cracked to shit
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps37487bfb.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps37487bfb.jpg.html)

Pretty sure the factory camber link shouldnt be bent lol
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps53637ab0.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps53637ab0.jpg.html)

Scrub the subframe clean with a red scuff pad and burn the bushings out
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps7621d2aa.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps7621d2aa.jpg.html)

Then I started spraying things
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps07a04dfb.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps07a04dfb.jpg.html)

Diff with installed solid mount and bushings
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpscb9275cd.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpscb9275cd.jpg.html)

Subframe mounts in with diff
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps8802bee6.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps8802bee6.jpg.html)

Complete rear end minus axles and brakes
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsedc52c13.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsedc52c13.jpg.html)

Rear end is now reinstalled and ive been driving the car around heres a few final shots.

Drivers view
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps0214ce8e.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps0214ce8e.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpse3af1f33.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpse3af1f33.jpg.html)
http://i18.photobucket.com/albums/b116/StolenSol93/null_zps551dfe82.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zps551dfe82.jpg.html)

picking up food is what it mostly does lol
http://i18.photobucket.com/albums/b116/StolenSol93/null_zpsab97cab1.jpg (http://s18.photobucket.com/user/StolenSol93/media/null_zpsab97cab1.jpg.html)

[LaMaR-]

Around December 2013 I deployed yet again. Not anywhere bad, just Okinawa Japan. 8 months in a country where I would love to drive so many cars that are a norm for the locals. I had a blast and really was looking forward to buying parts while I was there and shipping them back. No luck on that, all I bought was a set of mirrors. Ill get to that later though.

While in Japan I met quite a few people, mostly air force, that were into cars. I love photography and really want to better myself so I decided to try and get them to let me shoot their cars. Heres the outcome...

http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0039_zps4fff673b.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0041_zpscb0617c7.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0042_zpse178d3f4.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0049_zps273ca9c0.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0062_zpsccf9d326.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0070_zps223be4fc.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0148_zps21f7cfb8.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0170_zpsfebe267e.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0175_zpsfda4477e.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0211_zps7b9626bd.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0225_zps4e00120f.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0234_zps3dbf9135.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0239_zpsb76c2efb.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_0275_zps7208006b.jpg

[LaMaR-]

Back to my car now... I got back and drove around the RX7 for a little bit, it had no plates or insurance so it was mostly just starting it up, letting it idle for 5-10 minutes then driving it around the block and then parking it again. Nothing too exciting.

While I was deployed I started to order a few parts. Nothing major.
ASD Hydraulic Ebrake
http://i18.photobucket.com/albums/b116/StolenSol93/asd_zps67531fe8.jpg
RaceFab dual caliper bracket
http://i18.photobucket.com/albums/b116/StolenSol93/brackets_zps88e84539.png
PBM suspension pieces - I currently own everything made for the rear end of the RX7
http://i18.photobucket.com/albums/b116/StolenSol93/pbm_zps021c41d2.jpg

The car had a sketchy cage in it ever since I bought the car and I really wanted to go ahead and get a FD legal cage put in so I started cutting out the cage and the old cage mounts. What a pain in the A** that was.
http://i18.photobucket.com/albums/b116/StolenSol93/FC/IMG_0647_zps35e0a804.jpg

I had torn the car completely down so I could do bodywork and have the car finally become the car I had always dreamed of it becoming.
http://i18.photobucket.com/albums/b116/StolenSol93/FC/IMG_0652_zps78aa27c6.jpg

At some point during the cage cutout I decided it was going to be way to much work and I really needed to find a new shell instead of wasting my time. A couple months later I sold my 2013 GSXR-1000 and ended up finding a Black shell that was "pretty clean" other then the 6 coats of paint that would need to be stripped off of it. I actually don't have any photos at this time of when I first bought it, but just imagine a completely stock FC RX7. This one was my 4th FC and actually the worst one I've ever purchased. I looked at the car at night and for some reason trusted the seller about it being rust free...

With the money from selling my bike I decided I wanted to order some more parts.
Shine Autosports 30mm rear overfenders
Shine Autosports 30mm ventless front fenders
Shine Autosports Roof spoiler
S13 Coupe Rocketbunny rear spoiler
Replica BN Sports Type 1 kit
Varrstoen ES2 18x9.5/10.5 wheels

After all these parts arrived it was time to pull my motor out of the blue car and get it sold. This was the first time I've actually pulled the motor and since I was going to keep the subframe from the blue car I decided it might be easiest to just drop it through the bottom and pull the car up and over it when it was out. Again What a pain in the A**.

After finally selling the blue car I started to work on cleaning up the bay.. Heres a couple photos of that work going down. Now remember there was probably 6 coats of paint on the whole car and it had to be stripped in order to apply new paint and to make sure it doesn't have any chipping or peeling issues.
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps5d0a84dc.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps24f3c09a.jpg
Finished bay for now, still to come is tubs and welding up all the unused holes. Then I will paint it and add gold heat reflective tape to the firewall
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps86914b65.jpg

Lastly here you can see the "finished" bay and my motor patiently waiting to be rebuilt and cleaned up
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zpsfd52d4ba.jpg

[LaMaR-]

I guess I can't leave anyone hanging on what its gonna look like roughly lol

Heres a rough look at the rear of the car. The tire size and height is going to change quite a bit still.
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps76b64bac.jpg

http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zpsc4fd4f3c.jpg

and heres the money shot.. The front end :)
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps36cbfd4d.jpg

and in the end i would love for it to be a similar color to this S13.
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zps41c92b0f.jpg

I've was slowly working on getting the front suspension and subframe cleaned up and put back in so I could have a rolling chassis again. One of the biggest things I wanted to change this time around was the add power steering to the car since it never had it, now I know why it didn't lol. The motor mounts made it so that I had to bend custom lines to fit, and while doing so I came to find out that its hard to find the fittings for these racks anywhere local. I might end up ordering some later on and go ahead and bend custom lines if the ones I have on there now don't work.

I ended up taking the stock lines and adding a couple bends to them and removing a little out of a couple bends. Heres where I am at with the power steering setup.
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zpsc0d98575.jpg

From there I had to put back in the A arms and coilovers so i could throw the wheels back on and for the first time see it on all four wheels.
http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zpse338c5bc.jpg

http://i18.photobucket.com/albums/b116/StolenSol93/Mobile%20Uploads/image_zpsd5ac7a8d.jpg

[LaMaR-]

I go through cars too fast, The last car I posted ended up having a lot of rust that I didn't see originally, I guess I should have looked at it better. Also while working on it I noticed that the drivers floor was buckled a bit and came to a conclusion that it was probably hit in the door which is why the door doesn't fit 100% and the rocker was rusted. I begin my hunt for another shell and ended up calling about a car that was posted on craigslist. It ended up being about 10 minutes from my house and the guy just wanted it out of his yard so I went and looked at it really quick.
Heres the photos of how it sat when I went to look at it.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5189_zpsyul6ujdb.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5190_zpsxqd6zlds.jpg

I didn't jump on it right away because it was a automatic and I knew the transmission mount was different from manual trans cars to automatic. IDK why mazda would do this but whatever thats life lol. I come home and call up Grannys speedshop and get a price for a new mount, it was way cheaper then I expected so I ordered and it drove back down to look at the car more thoroughly. It was really clean and had everything I needed for my current car. Needs a windshield but that will come later on I suppose.

Well I picked the car up Tuesday 24FEB15 and had it towed to my house.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5206_zpsal8ry9ti.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5204_zpsbbrr7rug.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5205_zpsjdssywm6.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5203_zpsbhhbgrjc.jpg

Then wednesday 25FEB15, less then 24 hours later I had my suspension and wheels on the car just so I could get an idea of how they would look. In my opinion the tires are way too stretched for my taste so they will be changed out but overall I'm really happy with it. I can't wait to get my motor in this car and finally be able to drive it again.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5209_zpshakycm1d.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5212_zpsm3y4yyda.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5210_zpsqrttzxow.jpg

Then today when I got home I wanted to get an idea of how low it would be with the skirts on. so I threw the drivers side on.. I really can't wait now.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5215_zpsm4v8jvhl.jpg

Thats all for now, but as soon as I can get the bay painted I will be putting the motor in and sending it off to have an exhaust made for it.

http://i18.photobucket.com/albums/b116/StolenSol93/IMG_5211_zpsg9rhibst.jpg

After a very long hiatus from this project and spending much of my time working on my house, I finally decided it was time to start working on it again. I got the motor bolted back in for a test fit and went to put in the new transmission cross member and realized that I was sent the wrong one. So I couldn't finish that goal. On the plus side though, I did get ahold of Grannys Speed Shop and talked to them about the issue, they are sending me the correct mount this week at no charge. Couldn't be happier.

Well with that part on hold yet again I decided why not actually go ahead and test fit all of my panels, besides the rocket bunny wing but that'll come later lol. Everything fits really well except the front bumper, I need to figure out what to do in order to relieve some pressure off of the fenders.

Sorry in advance for the horrible photos but the car is too low to get out of the garage. I think that a taller sidewall on the rear tires will help since I don't really want to raise it up any. Onto the photos.

http://i18.photobucket.com/albums/b116/StolenSol93/fc1_zpshck2ce6c.jpg

http://i18.photobucket.com/albums/b116/StolenSol93/fc2_zpsgqkvjljj.jpg

http://i18.photobucket.com/albums/b116/StolenSol93/IMG_1937_zpslhmxadmz.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_1907_zpsmvvauy0f.jpg

In this photo you can see that the rear tire is actually low on air plus its super stretched, not really my style. Bigger rear tires will be going on for sure.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_1943_zpsfmmorspr.jpg

Last but not least I figured I would throw in a photo of my house with the car. Love how both of them look and can't wait to have the car streetable again.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_1954_zpsobptw4nn.jpg

[LaMaR-]

FEB2016

So I haven't gotten a lot of work done lately, mainly due do a lot of knee pain after having knee surgery. Today I finally got around to doing a few things that Ive been wanting to do. First thing was to start glassing my rear spoiler back together as one piece. This was my first time working with fiberglass in years and figured it would be the easiest thing to do.

http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7147_zpsu7wzdqgd.jpg
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7151_zpscpdl7fyn.jpg

the second thing I've been wanting to do was figure out why my front bumper pulled my fenders in so hard. I bolted back on my factory fenders and threw the bumper back on and realized that it was roughly an inch too narrow. Time to cut it in half and begin the process of widening it...No fun thats for sure, but it will fit much better and give me some practice with bodywork again. Its been too long.

First side before cutting
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7154_zpsng7dkmz9.jpg
other side
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7153_zpsyobcoxls.jpg

http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7155_zpsdpgmxv95.jpg
Fit the first side
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7156_zpszkh3cmza.jpg
then the other side
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7157_zpsuyzspueo.jpg

Heres the gap I'm going to need to fill, not bad at all. Obviously I need to do a little final fitment on the hood gap but I'm not worried about making it exact since this isn't going to be a show car, i plan to drive the hell out of it and enjoy it.
http://i18.photobucket.com/albums/b116/StolenSol93/IMG_7158_zpsfliwxysx.jpg

[LaMaR-]

Not long after fiberglassing that front bumper back together I lost all interest in the car. It seems to happen once in awhile and it actually took me until about June or July this year to get started again. But here it is finally getting worked on again.

So its been awhile and I finally have had the time and motivation to start working on her again.

So I finally put the motor back in the car to see if I could figure out a way to get it to fit under a stock hood. So far thats a no go but I am still trying to figure out a way.
https://c6.staticflickr.com/9/8870/28903248365_6dc51e0c1a_z.jpg (https://flic.kr/p/L35GLn)Rx7 project (https://flic.kr/p/L35GLn) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c4.staticflickr.com/9/8282/28827785531_97a3b6f311_z.jpg (https://flic.kr/p/KVpWi2)Rx7 project (https://flic.kr/p/KVpWi2) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

After deciding that I needed to move forward and concentrate on something new, I pulled the motor and started to clean her up.
https://c7.staticflickr.com/9/8528/28872044966_d4ef79a26e_z.jpg (https://flic.kr/p/KZjM5J)Rx7 project (https://flic.kr/p/KZjM5J) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

after scrubbing the trans for awhile it looked like this and then the primer and paint went on.
https://c4.staticflickr.com/9/8832/28288040283_d18a418444_z.jpg (https://flic.kr/p/K6HAQt)Rx7 project (https://flic.kr/p/K6HAQt) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c8.staticflickr.com/9/8304/28827785031_2fb8193d43_z.jpg (https://flic.kr/p/KVpW9p)Rx7 project (https://flic.kr/p/KVpW9p) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

After completing the easy part, it was time to move onto the motor. I didn't want to tear it all the way down, I just wanted to replace all the gaskets and really clean it up quite a bit. So out came the scrub brush again and after some hard work I finally got it to this point.

Initial Tear down
https://c2.staticflickr.com/9/8734/28288455993_f03d509663_z.jpg (https://flic.kr/p/K6KJpT)Rx7 project (https://flic.kr/p/K6KJpT) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

clean and prime
https://c3.staticflickr.com/8/7636/28872368026_683c733b47_z.jpg (https://flic.kr/p/KZmr7J)Rx7 project (https://flic.kr/p/KZmr7J) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

and some silver paint to really make it pop. The valve covers and some pulleys will be sent out for powder coating here soon, so I'm not too worried about the overspray.
https://c5.staticflickr.com/9/8754/28618621820_a1acd1c8b2_z.jpg (https://flic.kr/p/KAVVd9)Rx7 project (https://flic.kr/p/KAVVd9) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

After finishing up cleaning the motor I decided it was time to get the rest of the car in order. I was waiting on a ton of parts to come in anyway to finish rebuilding the motor.

First things first, cut and weld up the rear quarters for the wide body. I didn't want the normal cutout that people do because I will be driving the car on the street as well as the track so it needed to be closed off to the elements.

First thing I did was cut the outer panel off and then sliced the inner panel so that it would be easier to work with.
https://c6.staticflickr.com/9/8694/28903271565_c46886fcb0_z.jpg (https://flic.kr/p/L35PEn)Rx7 project (https://flic.kr/p/L35PEn) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
Then I bent all the metal outward and welded the seam and sealed it.
https://c4.staticflickr.com/9/8821/28903304995_f863f47131_z.jpg (https://flic.kr/p/L35ZAK)Rx7 project (https://flic.kr/p/L35ZAK) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
Drivers
https://c3.staticflickr.com/9/8857/28872060986_15953ce67f_z.jpg (https://flic.kr/p/KZjRQW)Rx7 project (https://flic.kr/p/KZjRQW) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
Passengers
https://c3.staticflickr.com/9/8629/28798350202_75ab57fea7_z.jpg (https://flic.kr/p/KSP5cm)Rx7 project (https://flic.kr/p/KSP5cm) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Rear panels put back on just to show that nothing can be seen.
https://c4.staticflickr.com/9/8555/28903405675_fc5cbbc9d1_z.jpg (https://flic.kr/p/L36vwB)Rx7 project (https://flic.kr/p/L36vwB) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c2.staticflickr.com/9/8568/28827813761_cf4ba89f9f_z.jpg (https://flic.kr/p/KVq5FK)Rx7 project (https://flic.kr/p/KVq5FK) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Also not shown, I ended up ordering an angle kit from the Villains drift team out in Washington state. Really is a simple design but it works great. I can't wait to test it out and drive this thing.

[LaMaR-]

Two week ago I started slowly working on the engine bay, stripping it down and getting ready to weld in a set of tubs. Im taking my time and making sure that everything is perfect side to side. I want the bay to be very clean since most of the time it will be out in the open until I figure out what to do for a hood.

The mandatory "Before"
https://c3.staticflickr.com/9/8737/28872039906_b005208a51_z.jpg (https://flic.kr/p/KZjKzu)Rx7 project (https://flic.kr/p/KZjKzu) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

beginning to cut out the original tubs and realizing that the metal is a bit sharper then my thumb could handle lol. Not a bad cut but just enough to sit there and bleed constantly. Nothing a little tape can't fix right?
https://c8.staticflickr.com/9/8565/28827792591_178a63c73c_z.jpg (https://flic.kr/p/KVpYoK)Rx7 project (https://flic.kr/p/KVpYoK) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Test fitting the first side, just a note, those "welds" up top are from another shell that I previously sold. The welds were from a flux core welder and looked like absolute garbage. I learned my lesson and they have now been ground off to prepare for the install.
https://c1.staticflickr.com/9/8844/28618356760_5c5f293976_z.jpg (https://flic.kr/p/KAUyq9)Rx7 project (https://flic.kr/p/KAUyq9) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

How I left her two nights ago
https://c1.staticflickr.com/9/8001/28285857104_8e622ef997_z.jpg (https://flic.kr/p/K6wpRs)Rx7 project (https://flic.kr/p/K6wpRs) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Yesterday after work I got home and began working again.
First things first, I wanted to verify that I had enough of the factory tubs removed and placed but of the new tubs in place and made sure they were even side to side. As I stated before, I want this thing to look identical side to side since it'll be shown off quite frequently.
https://c7.staticflickr.com/9/8150/28618491630_d9a6f6be5f_z.jpg (https://flic.kr/p/KAVfvu)Rx7 project (https://flic.kr/p/KAVfvu) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Everything looking pretty good so now its time to strip it all the way down.
https://c5.staticflickr.com/8/7753/28872105356_ec371ac4b2_z.jpg (https://flic.kr/p/KZk62W)Rx7 project (https://flic.kr/p/KZk62W) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Finally getting close but sick of sanding everything down I decided to tackle another job since the materials finally came in. Instead of running long tube BBK headers this time around I opted for a set of shorties. Going this route will change the amount of torque I end up having but it will allow me to lower the car quite a bit more which in my opinion is a better option.

Just a quick before and after. Not too bad for my first time wrapping headers.
https://c7.staticflickr.com/9/8892/28872340246_1fe752f2ce_z.jpg (https://flic.kr/p/KZmhRL)Rx7 project (https://flic.kr/p/KZmhRL) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/9/8770/28798515412_2475262057_z.jpg (https://flic.kr/p/KSPViN)Rx7 project (https://flic.kr/p/KSPViN) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c3.staticflickr.com/8/7662/28872345386_b85c1d1eb2_z.jpg (https://flic.kr/p/KZmjoo)Rx7 project (https://flic.kr/p/KZmjoo) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Thats all for now but I am working on the car daily so expect more updates to come. If anyone has any comments or suggestions I would love to hear them.

[LaMaR-]

16AUG - The nice thing about Jacksonville Florida is that we actually have a shop dedicated to drifting.. The bad thing is, they can't do any fab work lol, what kind of shop is that??

Ive been working on doing tubs and after a busy weekend I got back to work.
Started out making sure everything was nice and level side to side.

https://c6.staticflickr.com/9/8481/28417296053_6611dd1c76_z.jpg (https://flic.kr/p/Ki955e)Untitled (https://flic.kr/p/Ki955e) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

From there I just started slowly tacking everything into place. Nice and slow and trying to keep everything as clean as possible.
Far from perfect but for someone who hasn't done any sort of welding class I would say its not bad at all.

https://c2.staticflickr.com/9/8295/28417292953_9745e69edd_z.jpg (https://flic.kr/p/Ki949M)Untitled (https://flic.kr/p/Ki949M) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

both sides in.
https://c4.staticflickr.com/9/8431/28417295283_4240075137_z.jpg (https://flic.kr/p/Ki94QX)Untitled (https://flic.kr/p/Ki94QX) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Because I want it to look good I am going nice and slow so heres where I stopped tonight. I started to make templates out of cardboard but I think tomorrow on my way home from work I am going to stop and grab some poster board since its easier to work with.
https://c3.staticflickr.com/9/8847/28414074074_fb2d7bbbee_z.jpg (https://flic.kr/p/KhRyhS)Untitled (https://flic.kr/p/KhRyhS) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c3.staticflickr.com/9/8333/28414076594_52d32fd984_z.jpg (https://flic.kr/p/KhRz3j)Untitled (https://flic.kr/p/KhRz3j) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

Finally here is the last photos being dumped and the most up to date. Im in Charleston for the weekend for my moms birthday so I will get back to work early next week.

18AUG16
Started on the drivers side and got almost everything Tacked into place. Ill finish it up monday or tuesday this week and move onto cleaning everything up and priming it and painting the bay.
https://c2.staticflickr.com/9/8340/29000418801_3d7303f8c7_z.jpg (https://flic.kr/p/LbEJ9H)Untitled (https://flic.kr/p/LbEJ9H) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Side to side its pretty darn close I must say.
https://c3.staticflickr.com/9/8542/28456053514_3e354b50a6_z.jpg (https://flic.kr/p/KmyHjj)Untitled (https://flic.kr/p/KmyHjj) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[Reece]

I'm thoroughly enjoying this thread, to be honest. I've never been a fan of V8 swaps but a well built V8 FC is something I wouldn't mind.

[LaMaR-]

I'm thoroughly enjoying this thread, to be honest. I've never been a fan of V8 swaps but a well built V8 FC is something I wouldn't mind.

Thanks man, I am being put to shame by Jared and his Le RB-7 but its all in good fun. Maybe for my next one ill build something crazy like his. Or a jz powered Fd if all goes well with this one...

[an_orange_s2k]

awesome build man. love reading up on FCs

[LaMaR-]

by far my favorite car ever, if you missed it lol this is my 5th one... On a side note though, Jareds car is making me want to RB swap something so maybe I will do that later on to this car or maybe my BRZ lol goals...

[LaMaR-]

A little bit of filler and some seam sealer and these tubs will be ready for paint.

https://c1.staticflickr.com/9/8223/29154479776_70744fa385_z.jpg (https://flic.kr/p/Lqhk7q)Untitled (https://flic.kr/p/Lqhk7q) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

can't wait to get it done and put the motor back in one last time.

[ehhhregartless]

I thought I was on rx7club for a min. Cars' looking great

[LaMaR-]

Lol I love Zilvia from when I had my s13. Plus you get way more feedback here and people seem to enjoy the drift inspired builds

[fallen_51]

Ughhhh love this ! Good job man !


Sent from my iPhone using Tapatalk

[LaMaR-]

Ughhhh love this ! Good job man !


Sent from my iPhone using Tapatalk

I appreciate it man. Slowly getting it to where I want. This was my first time ever doing tubs or any sort of fab work so I am very happy with the results. I have a few ideas of how I will do the next set differently though.

[LaMaR-]

Haven't had too much time this week and I will be working this weekend so I decided to take advantage of a free night and get my radiator support welded into place. Nothing special but it does allow me to slant the radiator forward and keep it in place. Nice and simple nothing over the top.

https://c5.staticflickr.com/9/8460/28614023524_bf49c4abe9_z.jpg (https://flic.kr/p/KAwmib)Untitled (https://flic.kr/p/KAwmib) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

and how it looks installed.

https://c3.staticflickr.com/9/8121/28948920730_98fcaed8fc_z.jpg (https://flic.kr/p/L77MyW)Untitled (https://flic.kr/p/L77MyW) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/9/8195/29128613812_5cb4640a6c_z.jpg (https://flic.kr/p/LnZL4w)Untitled (https://flic.kr/p/LnZL4w) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

The last thing that I need to do prior to paint is to build a mounting bracket for my oil cooler setup. I need to throw the front bumper into place and make sure that I place it properly into one of the openings.

[SupaDoopa]

Please, please, please get rid of that wing. It completely kills the sleekness. Other than that, I like where this is going!

[LaMaR-]

Please, please, please get rid of that wing. It completely kills the sleekness. Other than that, I like where this is going!

I appreciate the kind words. Personally I love the rear spoiler but I may try to find something different in the future. For now since I already have it I am going to finish it and see how it looks in the end.

Stay tuned :)

[WPN-X7]

rad build dude!

having done a LS FC drift car a while back (before my current s14s) i played around with a heap of different lock kits/cut and shut knuckles.

do yourself a favour and just order PBMs drop knuckle/LCA combo. by far the best i drove with.

[LaMaR-]

rad build dude!

having done a LS FC drift car a while back (before my current s14s) i played around with a heap of different lock kits/cut and shut knuckles.

do yourself a favour and just order PBMs drop knuckle/LCA combo. by far the best i drove with.


lock kits? as it angle kits?

Also do you have any info on how to either weld up a T2 diff or how to put bigger shims in it in order to lock it up better?

[WPN-X7]

lock kits? as it angle kits?

Also do you have any info on how to either weld up a T2 diff or how to put bigger shims in it in order to lock it up better?


yeah sorry angle kits (im aussie so different terminology haha)

i only ever ran a 2 way in mine so cant help with the welding/shimming thing. fairly certain theres a few guides on RX7 club/ausrotary etc to do it. now that i think about it shimming a FC diff shouldnt be any different to a S chassis r200 (could be wrong there however)

[LaMaR-]

yeah sorry angle kits (im aussie so different terminology haha)

i only ever ran a 2 way in mine so cant help with the welding/shimming thing. fairly certain theres a few guides on RX7 club/ausrotary etc to do it. now that i think about it shimming a FC diff shouldnt be any different to a S chassis r200 (could be wrong there however)

Ill have to look more into it later on. First and foremost I want to get her running again and go for a ride lol.

Thanks again for the kind words and I will be sure to keep this updated.

[Reece]

Once again, good progress!

Question quick, how did the other FC drive with the 302 in it? Did it still feel somewhat balanced?

[LaMaR-]

Once again, good progress!

Question quick, how did the other FC drive with the 302 in it? Did it still feel somewhat balanced?

It actually wasn't too bad. I never really got to push it on the street like I wanted to. I don't mean drifting, just driving and enjoying the highway. It always idled weird and I never felt comfortable and confident in it. This time around, once I finish the rebuild, I will be getting it tuned by a local guy and throw it on a dyno. I want to know that the car is reliable enough for me to drive an hour across town without breaking down lol.

On a side note, with all of the suspension upgrades since the last time I drove the car you really shouldn't notice too much of a weight difference. We shall see though.

[LaMaR-]

I ordered these spacers from Xcessive Manufacturing. They are one inch spacers for the subframe and I am really hoping they will give me enough clearance to run the factory hood.
https://c7.staticflickr.com/9/8135/29318685966_57fca26c45_z.jpg (https://flic.kr/p/LEMVTC) (https://flic.kr/p/LEMVTC) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Then threw the wheels back on to see how everything fit and see the new angle now that the tubs were completed.

https://c7.staticflickr.com/8/7565/29244160222_37d008bc8c_z.jpg (https://flic.kr/p/LycXZ1) (https://flic.kr/p/LycXZ1) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c7.staticflickr.com/9/8211/29064748270_e0c9dfd4c8_z.jpg (https://flic.kr/p/Lhmr4u) (https://flic.kr/p/Lhmr4u) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Last but not least since I am now waiting to throw some real primer on the bay so that I can wet sand and paint it, I decided that I might as well throw on the bumper and fenders just to see who my clearance is. Before anyone says it, I know that I need to bring the rear end down some more.

https://c7.staticflickr.com/9/8316/28728892134_3b396d949d_z.jpg (https://flic.kr/p/KLF5Js)Untitled (https://flic.kr/p/KLF5Js) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Passenger fender fitment
https://c4.staticflickr.com/9/8455/28730942883_3101cab34d_z.jpg (https://flic.kr/p/KLRAmc)Untitled (https://flic.kr/p/KLRAmc) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Drivers
https://c7.staticflickr.com/9/8078/28728885614_ab968d5043_z.jpg (https://flic.kr/p/KLF3N3)Untitled (https://flic.kr/p/KLF3N3) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Here you can see how much I had to widen the front bumper in order to make it fit decent.. Some of these replica kits are absolutely ridiculous.
https://c6.staticflickr.com/9/8017/28730940133_dbb0f8b5cf_z.jpg (https://flic.kr/p/KLRzwM)Untitled (https://flic.kr/p/KLRzwM) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c6.staticflickr.com/9/8524/29351897805_9eb21e2648_z.jpg (https://flic.kr/p/LHJ9Bx)Untitled (https://flic.kr/p/LHJ9Bx) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c7.staticflickr.com/8/7495/28728887654_4ede65d492_z.jpg (https://flic.kr/p/KLF4pd)Untitled (https://flic.kr/p/KLF4pd) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

I can't get over how much I love the look of this car now. First and foremost I got the sealer on the tubs and had planned on having it fully primed, wet sanded and painted this weekend but those plans fell through... Maybe next week. On to everyones favorite thing.. PHOTOS!!

https://c1.staticflickr.com/9/8014/29433349696_824b48ec20_z.jpg (https://flic.kr/p/LQVBqu)Untitled (https://flic.kr/p/LQVBqu) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c6.staticflickr.com/9/8242/29388046101_d18a35581d_z.jpg (https://flic.kr/p/LLVqf2)Untitled (https://flic.kr/p/LLVqf2) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c1.staticflickr.com/9/8491/29433343936_bea67d49e4_z.jpg (https://flic.kr/p/LQVzHb)Untitled (https://flic.kr/p/LQVzHb) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c5.staticflickr.com/9/8253/29433343476_be8922eacd_z.jpg (https://flic.kr/p/LQVzzf)Untitled (https://flic.kr/p/LQVzzf) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c1.staticflickr.com/9/8485/29433347136_c48971dd96_z.jpg (https://flic.kr/p/LQVAEm)Untitled (https://flic.kr/p/LQVAEm) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c6.staticflickr.com/9/8036/29388043101_477e3bc7b7_z.jpg (https://flic.kr/p/LLVpmi)Untitled (https://flic.kr/p/LLVpmi) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

Decided that it was about time I start throwing my motor back together so I gathered all my parts and slowly begin putting parts on. This is my first time doing any of this so I decided to take my time and make sure everything was done the right way the first time.

Motor upside down and parts in the background
https://c1.staticflickr.com/9/8055/29065062544_f0df86dba4_z.jpg (https://flic.kr/p/Lho3u1)Untitled (https://flic.kr/p/Lho3u1) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

timing cover and water pump on as well as harmonic balancer installed
https://c8.staticflickr.com/9/8472/29066664543_607401f635_z.jpg (https://flic.kr/p/LhwfGF)Untitled (https://flic.kr/p/LhwfGF) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

and flipped back over. Everything is looking really good and I can't wait to get the valve covers and pulleys painted to match the engine bay. Im hoping for sunday but it might be next weekend... We shall see soon.

https://c7.staticflickr.com/9/8137/29065063494_dddb0b9545_z.jpg (https://flic.kr/p/Lho3Lo)Untitled (https://flic.kr/p/Lho3Lo) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

Slowly putting the motor back together and now I'm trying to figure out how to get custom power steering lines made.

https://c6.staticflickr.com/9/8325/29738355581_a567ee89f7_z.jpg (https://flic.kr/p/MiSR3D)Untitled (https://flic.kr/p/MiSR3D) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

and heres the new power steering bracket that I ordered a couple weeks ago. Not sure why I took such a bad photo but whatever lol you get the idea.

https://c1.staticflickr.com/9/8688/29785456376_a85863c2f3_z.jpg (https://flic.kr/p/Mo3ftj)Untitled (https://flic.kr/p/Mo3ftj) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Last but not least I applied for a "racer" sponsorship through Mishimoto and got accepted. The first part that I ordered was a oil cooler and probably next year I will go ahead and order a new radiator to help with cooling if needed.

This kit was very well packaged and built to bolt onto a 1990 Ford Mustang GT. Obviously I ordered the kit due to the motor. To make it fit I had to bend a piece of aluminum and drill a few holes for a bracket and then I ended up welding the other side onto the front of the frame rail. It fits perfect and should get really good airflow to keep everything nice and cool.

https://c4.staticflickr.com/9/8239/29821222955_a002db238b_z.jpg (https://flic.kr/p/MrcyCt)Untitled (https://flic.kr/p/MrcyCt) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c3.staticflickr.com/9/8140/29785454466_5184ea188d_z.jpg (https://flic.kr/p/Mo3eUo)Untitled (https://flic.kr/p/Mo3eUo) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Last but not least I finally made my way down to Orlando SpeedWorld to check out some local drifting. Heres a quick 1 minute video I threw together on Instagram.
https://c5.staticflickr.com/9/8101/29528365860_b2c4c77961_z.jpg (https://flic.kr/p/LZjAqd)Untitled (https://flic.kr/p/LZjAqd) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

If you wanna check out my IG and follow along there, find me at JMande09

[slidewayz240]

the car is coming along awesome dude! cant wait for you to get that bay painted.

[LaMaR-]

Something cool happened...

https://c5.staticflickr.com/9/8570/30277092636_bc97a4f26c_z.jpg (https://flic.kr/p/N8u1Ny)Untitled (https://flic.kr/p/N8u1Ny) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

I also ordered a pretty rare set of wheels for her... 18x10/11 +17.. Kinda want a lower offset but maybe later.

[LaMaR-]

Slowly getting closer to putting the motor back in...
https://c1.staticflickr.com/6/5492/30320506192_1f843afd04_z.jpg (https://flic.kr/p/Ncjw99)Untitled (https://flic.kr/p/Ncjw99) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

Well I've been in Washington State now for a few weeks and its almost time to head back home for Thanksgiving. I did get a package in right before I left so I figured since I have time I would go ahead and throw you guys some more photos.

Started putting the engine bay back together. I still need to run the brake lines through the new tubs but its getting closer.
https://c2.staticflickr.com/6/5341/31101273105_12e0ed2dbc_z.jpg (https://flic.kr/p/Poj9WD)Untitled (https://flic.kr/p/Poj9WD) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

And the newest package to arrive...
https://c2.staticflickr.com/6/5701/31101274425_d422cfde14_z.jpg (https://flic.kr/p/Pojakp)Untitled (https://flic.kr/p/Pojakp) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[Reece]

Oooooo I wonder what's in those boxes

[LaMaR-]

Here they are sorry, I've been on the otherside of the country for work. Ill finally get to go back home in about 3 weeks and then progress can begin again.

https://c4.staticflickr.com/6/5644/30987602291_63fa5c2ae0_z.jpg (https://flic.kr/p/Pdgyz2)Untitled (https://flic.kr/p/Pdgyz2) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/6/5782/30959041452_024af9a194_z.jpg (https://flic.kr/p/PaKbqL)Untitled (https://flic.kr/p/PaKbqL) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c7.staticflickr.com/6/5582/31065440246_ac524f524c_z.jpg (https://flic.kr/p/Pk9v5J)Untitled (https://flic.kr/p/Pk9v5J) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/6/5567/30292752604_95d1b8af6f_z.jpg (https://flic.kr/p/N9SgY1)Untitled (https://flic.kr/p/N9SgY1) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[LaMaR-]

Went to Washington state for a couple months for work but while I was there I ordered a speedway 22 circuit harness to help get everything wired up. Upon arrival home my father met me at my house and together we put my motor in and then back out and then back in one last time. Some how we managed not to scratch any of the paint.
https://c2.staticflickr.com/1/634/32078240681_599f83f8c1_z.jpg (https://flic.kr/p/QSDnnc)Untitled (https://flic.kr/p/QSDnnc) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c2.staticflickr.com/1/571/32196472585_f63870f42d_z.jpg (https://flic.kr/p/R46kAi)Untitled (https://flic.kr/p/R46kAi) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Then I proceeded to pull the valve covers to spray as well as a couple of the pulleys and install the power steering.
https://c6.staticflickr.com/1/586/32196470245_4a7e023331_z.jpg (https://flic.kr/p/R46jTX)Untitled (https://flic.kr/p/R46jTX) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c5.staticflickr.com/1/587/31821018820_e15e5dccff_z.jpg (https://flic.kr/p/QtV3gw)Untitled (https://flic.kr/p/QtV3gw) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

I absolutely love how everything has come together to this point. The colors and all the parts were just an image in my head that is finally becoming a reality.

https://c5.staticflickr.com/1/587/31821018820_e15e5dccff_z.jpg (https://flic.kr/p/QtV3gw)Untitled (https://flic.kr/p/QtV3gw) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/1/772/31354984244_8fe4791ed7_z.jpg (https://flic.kr/p/PLJuqC)Untitled (https://flic.kr/p/PLJuqC) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c8.staticflickr.com/1/471/31386261743_e7f2f5f546_z.jpg (https://flic.kr/p/PPuN8R)Untitled (https://flic.kr/p/PPuN8R) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c5.staticflickr.com/1/269/31354986604_ccb96c3c91_z.jpg (https://flic.kr/p/PLJv8j)Untitled (https://flic.kr/p/PLJv8j) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c1.staticflickr.com/1/643/32048010712_c666ffdf93_z.jpg (https://flic.kr/p/QPYr3Q)Untitled (https://flic.kr/p/QPYr3Q) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[CrimsonRockett]

This makes me want an FC.

Love your work so far!

[slidewayz240]

the car is coming along awesome dude! cant wait to see it running.

[LaMaR-]

This makes me want an FC.

Love your work so far!

The FC truly is my favorite car of this time frame. Just the overall style of the car is enough to make me happy. Although I do wish they had the simple rear suspension setup of the S13.

Thank you though, I can't wait to get her up and running again.

[LaMaR-]

Installed a few small things including the oil cooler setup. Need to finish tightening it down is all. Just a small list of things to complete before first startup..


-WIRING :(
-Tighten and bleed brakes
-Tighten and bleed clutch
-Fluids
-Install power steering cooler (post startup)
-Get custom power steering lines (post startup)
-Install hydro and second set of rear calipers (post startup)
-Exhaust (post startup)
-Seats and Seat Brackets
-Harness Bar
-Harnesses
-Dash
-Gauges
-NRG Hub
-Steering wheel
-couple small suspension pieces from PBM


and finally the picture you've all been wanting to see lol, she looks like a beast and I honestly can not wait to finally start her up.
https://c1.staticflickr.com/1/283/32019763550_5a2062e559_z.jpg (https://flic.kr/p/QMtE9N)Untitled (https://flic.kr/p/QMtE9N) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

[taeisbeast]

Looks great! makes me want to yank my motor out and fix up the bay for sure.

[greenwood]

sweet build!

Your oil cooler is upside down

flip so lines go in top or side not bottom.

[taeisbeast]

sweet build!

Your oil cooler is upside down

flip so lines go in top or side not bottom.

thats exactly what i was thinking,

[LaMaR-]

Looks great! makes me want to yank my motor out and fix up the bay for sure.

sweet build!

Your oil cooler is upside down

flip so lines go in top or side not bottom.

thats exactly what i was thinking,

You guys are both absolutely correct. I honestly didnt realize that it was and didn't think it matter but just in case I swapped it which makes its a lot safer anyway, I just flipped it over and shortened both lines up. Also installed the radiator and fan today. I must say that I am extremely happy that I measured and test fitted this thing before welding up the lower support. It fits perfect and gets plenty of airflow.

https://c1.staticflickr.com/1/582/31568713934_0ba3740c1f_z.jpg (https://flic.kr/p/Q6BUPh)Untitled (https://flic.kr/p/Q6BUPh) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

Radiator installed and a couple photos to show how much room i actually have left. Sorry for the horrible cell phone photos but its better than nothing I suppose.

https://c1.staticflickr.com/1/514/32033794390_9d5b00d54d_z.jpg (https://flic.kr/p/QNHz2Q)Untitled (https://flic.kr/p/QNHz2Q) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

https://c1.staticflickr.com/1/265/32411266685_6310b2313b_z.jpg (https://flic.kr/p/Ro5doR)Untitled (https://flic.kr/p/Ro5doR) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr
https://c1.staticflickr.com/1/330/32411267055_4d2592b7f9_z.jpg (https://flic.kr/p/Ro5dve)Untitled (https://flic.kr/p/Ro5dve) by J Manderville (https://www.flickr.com/photos/neiko09/), on Flickr

The radiator is something I will be replacing this year with something new from Mishimoto, but for now in order to get her back up in running I will just continue to use this one. Ive never had overheating problems so it works fine but I know the Mishimoto one will work much better.

[LaMaR-]

The car is for sale, it will come on 17" Enkei RP01s if anyone is interested. No bodykit included though. asking $3500 OBO although I don't believe anyone here will be interested, the more I put it out there the easier it should be to sell...

[Edwin Guy]

The car is for sale, it will come on 17" Enkei RP01s if anyone is interested. No bodykit included though. asking $3500 OBO although I don't believe anyone here will be interested, the more I put it out there the easier it should be to sell...
Nooooooooooooooo, why what happened? This gots to be the sadest ending to one of the most killer build threads ive read on zilvia!!! From the divorce to getting rid of the s13 to now this :'(

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Meh thats life I suppose. 2500 takes it or best offer at this point.

[hotlavaflow]

What the hell?! I got all into this and this is how it ends?...

[Edwin Guy]

Is it running? How much is left to do? Also located where?

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Trade ya my running ka24de 240sx on pbm coilovers, runs killer!

Sent from my LGMS550 using Tapatalk

[LaMaR-]

What the hell?! I got all into this and this is how it ends?...
This build has seen more traffic this week then it has in the past year lol. I figured no one gave two shits about it and this forum was dying.

Is it running? How much is left to do? Also located where?

Sent from my LGMS550 using Tapatalk
It turns over but I haven't fired it up yet. The car needs to be wired.

Trade ya my running ka24de 240sx on pbm coilovers, runs killer!

Sent from my LGMS550 using Tapatalk

Im kinda interested honestly. Where are you located?

[Edwin Guy]

This build has seen more traffic this week then it has in the past year lol. I figured no one gave two shits about it and this forum was dying.


It turns over but I haven't fired it up yet. The car needs to be wired.



Im kinda interested honestly. Where are you located?
Auburn Al, i was just in Jacksonville not to long ago actually! I was in fleming island like 2 weeks ago! I can post pics right quickhttps://uploads.tapatalk-cdn.com/20170406/7255be7b639ec599a9ffb9b25ef46ef9.jpghttps://uploads.tapatalk-cdn.com/20170406/dcaf0abe35b3b37a9c4382d8c7fa1b48.jpghttps://uploads.tapatalk-cdn.com/20170406/b6ca7632919b0a1cddd23a8945fa3ac2.jpg

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Parts list:
Xcessive intake
Oil catch can
New carbon fiber hydrodipped valve cover
Ebay seats with street faction seat bracket
Steel braided clutch line from slave to master and brake lines all around
Refurbished all donuts bc no funds for nice wheels
Gutted interior with somewhat new carpet
No speakers or radio due to weight reduction
Nismo power brace
Megan racing tension rod
Isr tie rods plus spare outer tie rod
Isc toe rod and brand new spare megan racing toe rods as well
The front rotors are also pretty new p2m drilled and slotted rotors.
Had her since last summer and been building her ever since barely got to drive her due to all sorts of leaks that are all sealed now, even redid upper timing, year later not even driven more then hour and half or so & after all the building i trusted her to get me to Jacksonville and back. Only suffered a broken tie rod but fixed it in st augustine beach! Now shes been a dailey and has kept up veryyyy nicely 10/10 would recommend for ka build! Just thought id entertain the thread. Lemme know what ya think and we might be able to work something out! Sick thread tho! https://uploads.tapatalk-cdn.com/20170406/ff535f0ebf431935abea2eacca2627b7.jpghttps://uploads.tapatalk-cdn.com/20170406/19a3ab2d59d1f0443c44125ee6dfbd34.jpghttps://uploads.tapatalk-cdn.com/20170406/27540408ffc0943d74008faa95364e9f.jpghttps://uploads.tapatalk-cdn.com/20170406/831b932b6432ee93e44ba2022b3976d1.jpghttps://uploads.tapatalk-cdn.com/20170406/60b22e18d848782eb90b4c6160072b71.jpg

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Coilovers are 2 weeks old and havnt even riden more then 150 miles or so, super nice ride no doubt!

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Hazaa bay pic!
Couple other things were the magnecore spark plugs wires and iridium plugs
Circuit sports overflow tank
Isr radiator
Deleted AC
Brand new hoses all around literally
Brand Energy suspension sway bar bushings and steering rack bushings
And week old new batteryhttps://uploads.tapatalk-cdn.com/20170406/9f7dae4ce232394405836329fdfae339.jpg

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Got the coilovers after the trip to Jacksonville if just in case someone says "how are they're only 150 miles on the coilovers if the you took it to jacksonville?" i got the coilovers 2 weeks after the trip with ya guessed it, tax money! 💰

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Lol, all good. What kind of deal are you thinking? I'm definitely interested

[Edwin Guy]

Well its my dailey, ya say it needs to be wired up as in all the wires are there but need to be mapped and tuned? How long do you think it would take to get her running? I would need to make that my dailey asap ya know?

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Haha shitty quality photos for the win

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Best thing i might add is that its a crackless dash aswell which i personally know is notorious in 240sx in this day and age

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Best thing i might add is that its a crackless dash aswell which i personally know is notorious in 240sx in this day and age

Sent from my LGMS550 using Tapatalk

correct all the wires are there, its actually a brand new speedway harness so it just needs to be wired up. The engine harness itself is already wired and just needs a power switch installed. If you know wiring I would assume that it would only take a weekend to finish up.

[Edwin Guy]

Hate to ask too 21 questions, but did ya ever get the windshield? Also trailering her would be a for sure? And possibly if i dedicated a whole weekend to it i could plus some youtube videos here and there. Are you or the car still in Jacksonville?

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Hate to ask too 21 questions, but did ya ever get the windshield? Also trailering her would be a for sure? And possibly if i dedicated a whole weekend to it i could plus some youtube videos here and there. Are you or the car still in Jacksonville?

Sent from my LGMS550 using Tapatalk

all good man but no I never did end up getting a windshield for the car and yes it would need to be trailered, The car is in Jacksonville but currently I am in WA until early may. The Navy loves sending me away lol

[Edwin Guy]

That's okay, gives me time to do a couple things to the car! Been wanting to try and get the dent out from the driverside quarter panel, and save up for the windshield if this happens to actually go down! The guy that sold me the car dailey drove her til she was ready die; the only money put in to her was just to keep her alive ya know? Refilling the power steering every other day bc he didnt want to fix leaks but rather refill her . she was covered in oil from wall to wall in the bay and under her. Spent tons of hours literally just cleaninge her up. emissions have been deleted due to xcessive intake. Cleaned up reallllllly nice!

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

Could ya give me a lil list of things that would finally get her back on the road? Dont hold back

Sent from my LGMS550 using Tapatalk

[LaMaR-]

windshield, wiring, and install driveshaft with new rear flange. Those three things alone would make the car drivable.

[Edwin Guy]

And the only thing you dont have is the windshiled correct? Next step would be to meet up and for you to check out my car, even if it doesnt happen i wouldnt mind a trip back to jacksonville for the hell of it!
Also got her a 255 walboro ltr fuel pump and since i got her ive only ever fill her up with premium
Minor thing is hood doesnt sit flush due to plenum or stock intake sitting to high due to plenum.

Sent from my LGMS550 using Tapatalk

[LaMaR-]

correct. Ill post back here when I get a date to head back home.

[Edwin Guy]

Sweeeet! This is hell of an ending now man, the story goes on!!!

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Just wanted to let you know I was back in Jacksonville finally. A bit early but I'm back lol

[Edwin Guy]

Damnnnnnn man really, i literally just got back from Jacksonville. Literally got home last night from a week trip down there.

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

I forgot to check the forum. I wanted to get ahold of ya there but i got too busy

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

How long are ya gonna be there? Im gonna be taking another trip back this month

Sent from my LGMS550 using Tapatalk

[Edwin Guy]

How far are ya from fleming island?

Sent from my LGMS550 using Tapatalk

[LaMaR-]

How far are ya from fleming island?

Sent from my LGMS550 using Tapatalk

Im heading back out of Town on the 30th for another month. Fleming Island is maybe 20 minutes away.

[Edwin Guy]

Alright, if its cool with you i dont mind waiting another month. I really need to get my funds back together

Sent from my LGMS550 using Tapatalk

[LaMaR-]

Cars sold. New car is already in possession and ready to be widened lol


heart of a supra ;)

[Edwin Guy]

Well thats dope bro! Keep this thread alive!!

Sent from my LGMS550 using Tapatalk