1991 s13.5 Pink Beast RB25 to built JDM VVT-i 2jz!

[MC.Understeer]

Before
http://i49.photobucket.com/albums/f286/vr_sex/535092_404712049569077_244223235617960_1171912_814 656408_n.jpg
Got a really good deal on a JDM VVT-i 2jzgte is why I went ahead and decided to do the swap.
http://i47.tinypic.com/ke7wx0.jpg
Out with the old!
http://i50.tinypic.com/fokas6.jpg
New parts coming in! ARP L19 Headstuds, Main studs, 3 row Mishimoto rad, 1jz Bellhousing, Exedy twin, 87mm CP pistons, Eagle rods, Cometic hg, Clevite Race thrust washers, main and rod bearings, Xcessive Manufacturing jz mounts
http://i47.tinypic.com/16a8dc6.jpg
http://i45.tinypic.com/2qimvet.jpg
http://i48.tinypic.com/25jaulf.jpg
Anodized the block Purple!
http://i45.tinypic.com/ddpbix.jpg
http://i50.tinypic.com/23jh2l5.jpg
Rotating assembly in!
http://i48.tinypic.com/2i8ei3l.jpg
porting and knife edging. (This is taking longer than I wanted.. But atleast I understand why it cost so much to have it done by someone) Should be worth the extra time in the long run...
http://i45.tinypic.com/2mq47dj.jpg
Got some of the accessories on, had the alternator and turbo housing polished now I just need to finish the porting, order some valve springs and get the head surfaced and she'll be ready to install on the block.
http://i49.tinypic.com/1731mw.jpg
Got the head back from the Machine shop, resurfaced and all the valve seats cut. Had to order $100 in new valve shims to get in tolerance.
http://i46.tinypic.com/2j4ae7k.jpg
Installed the head, using stock valvetrain for now.
Almost ready to drop her in! ( valve covers and some other bits are getting polished also. Looks half a**ed right now )
http://i46.tinypic.com/eqvyqc.jpg
http://i47.tinypic.com/huqd7r.jpg

[JohanM]

Nice, maybe depending if I can find A decent 2jz vvti swAp with he maf ill go that route,
Did you get a maf with your swap?

[dreamin240sx]

So what was the reasoning of getting rid of the 26 for a j series.. both great motors haha was it because of parts availability... anyways you didn't go wrong should be an interesting build..

[StryfeS13]

Because 2JZ > RB....

[CleanAndLegit]

do you have a blackberry? ahaha my phone fogs up my pics like that.
looks like its gonna be a badass build can't wait for more!

[smink]

Because 2JZ > RB....

What he said

[d_nice]

looking good man keep it up

[Xracer]

Good stuff. Still have a hard time believing how well you are taking care of the car. Can't wait to see more progress. Keep it up.

[tricky_ab]

This has to be the worst camera phone ever...

Looks interesting (from what I can see)...

[food7373]

Very nice.

[bc.]

^great!!!! I could use duffel bags!!!!! #spammer

Looks like a serious build here, I think it deserves some serious pictures...

[MC.Understeer]

So what was the reasoning of getting rid of the 26 for a j series.. both great motors haha was it because of parts availability... anyways you didn't go wrong should be an interesting build..

:squint:

It was a 25neo not a 26 and I did it because I wanted a built motor and I didn't want to build a small liter engine. With the 1mm over I'm just a hair under 3.1 liters. Plus I love the sound of jz's.

LoL as for my camera the plastic part covering my camera lens was really scratched, I've removed it now. My camera is actually 5 megapixels.

[Weedm]

so it has come to this. cant wait to see the finished product, sir.

[MC.Understeer]

Finally finished up the valve adjustment and timing. Ready to install the twin disk and trans soon as I free up a lift at work.
http://i46.tinypic.com/j12at0.jpg

[driftlife.son]

humongous pictures!!

[MC.Understeer]

humongous pictures!!

Haha sorry most forums resize ill fix it.

Finally got a bigger turbo. Borg Warner S400
http://i49.tinypic.com/33xu5ud.jpg

[DJPimpFlex]

Because Daigo?

[pjurisprudencia]

I can see that there is some awesome stuff here but the big pictures are preventing me to see the awesomeness

[MC.Understeer]

Fixed, sorry for the pictures. Photobucket pi$$es me off. Tinypic actually let's you choose the resolution size.

[MC.Understeer]

Started making my turbo manifold. First one I've ever made so we'll see how it turns out.
http://i45.tinypic.com/20z3bll.jpg

Making progress, just need to move the turbo a little closer to the head I think. Going to mount the trans with no clutch and drop the engine in to check for clearence.

http://i47.tinypic.com/jgi13a.jpg

[d_nice]

looking good man..i keep checking on here to see how it goes

[MC.Understeer]

looking good man..i keep checking on here to see how it goes

Picked up 16 18x9.5 drift spares for a good deal, tires are on the way, also getting a tire machine and balancer tomorrow. Good stuff to have in this motorsports.
http://i47.tinypic.com/2mdmpn9.jpg

My VEMS standalone ecu's I ordered came in 3 days all the way from Europe. Great system, tons of options to select from when ordering the unit. Ordered a unit with dual EGT inputs, 4 bar map, SD card slot for data logging. What sold me on these units is vvti control, nitrous control, internal wideband output, o2 correction and of course price! Ordered 2 units and 4 sets of plugs so instead of having 4 cars with ecu's I can swap ecu's into different cars and just switch maps! Not gonna drive 4 cars at once anyways!
http://i47.tinypic.com/fqmwl.jpg

[MC.Understeer]

Finally spent some time on the build the last couple days, It might not seem like much but its alot of work to get the first runner mocked up and the collector made. Keep in mind this is the first manifold I've ever made and only the 3rd time ive ever welded anything in my life!
http://i46.tinypic.com/2ypi4h2.jpg
Using this Hatch I picked up and stripping down to put an rb25 in it for a back up car for turbo location and clearance in a s13 for the manifold.
http://i47.tinypic.com/110w513.jpg

[Imarvin240]

That's awesome news about the skyline! Extremely jealous!

[MC.Understeer]

Also picked up some Parts for the R154, im gonna find out how much power it can really hold next season.
http://i49.tinypic.com/24zats0.jpg

[EvoVIII808]

oh damn! Next year will be a sweet year for the track. hook me up with that RB.

[MC.Understeer]

oh damn! Next year will be a sweet year for the track. hook me up with that RB.

I don't have any spares, All my rb engines have cars they need to go into. After I send my million hp 2j into the wall I need to have a couple spare cars to drive after.

[EvoVIII808]

Shoots, i saw you last time smack the wall, and drive off like a beast with only minor damage (Headlight/Fender/Hood). Seeing you ride in action keeps me going, and that RB was tough. Keep it up!

[forzanoob]

Finally spent some time on the build the last couple days, It might not seem like much but its alot of work to get the first runner mocked up and the collector made. Keep in mind this is the first manifold I've ever made and only the 3rd time ive ever welded anything in my life!
http://i46.tinypic.com/2ypi4h2.jpg
Using this Hatch I picked up and stripping down to put an rb25 in it for a back up car for turbo location and clearance in a s13 for the manifold.
http://i47.tinypic.com/110w513.jpg
Picked up a R32 Skyline yesterday from Canada! They federally approved it for U.S registration under the Canadian Vin!
http://i50.tinypic.com/mvgidt.jpg

So how did this happen because i really want to know

[killer240]

maybe cuz he lives in seattle

[Tw1st3d]

I made my manifold as well, those collectors are a bitch huh?

coming along great keep it up

[MC.Understeer]

I made my manifold as well, those collectors are a bitch huh?

coming along great keep it up

Yeah I was going to buy one at first but no one really makes anything close to what I needed, Vibrant makes a 6-1 collector but not twin scroll or 1.25" like I needed. I finally made a jig for the wet bandsaw and it came out great. Also I don't have any practice welding but Id rather make my own the way I want and have it not look professional but cost me alot less and to be able to say I built everything myself.

Headed down to southern cali this friday to pick up a bunch of aero parts and maybe another project car as im in the middle of another s13.5 rb25 project.

[MC.Understeer]

Just got back from a 40+ hour road trip. Didn't keep me from trying to finish my turbo manifold. If it wasn't for my material supplier I would have finished it today...

Found a cool short clip on youtube someone made, working on getting more footage from the guy who made the video.

http://www.youtube.com/watch?v=qWxWbKMoIqU

http://i49.photobucket.com/albums/f286/vr_sex/IMG_20121230_174601.jpg

[EvoVIII808]

http://farm9.staticflickr.com/8363/8335032526_cb5016f4ca_z.jpg
http://farm9.staticflickr.com/8359/8335036106_cf08d5937a_z.jpg
who did your cage?

[Oakville]

You registered it federally under the canadian 17 digit vin? or 12 still from japan

[MC.Understeer]

who did your cage?

The guy I got the car from. I plan on cutting it out and making a new cage. I don' t think they're gonna let the cage slide for the 5/8ths bank since the way the cage is made isn't exactly correct.

[EvoVIII808]

The guy I got the car from. I plan on cutting it out and making a new cage. I don' t think they're gonna let the cage slide for the 5/8ths bank since the way the cage is made isn't exactly correct.

gotcha, well im in the market for a cage builder. If you know anyone that can do it please pass me their info. I have all the materials but no bender or decent welder.

One more pic to stay on topic with your build.
http://farm9.staticflickr.com/8496/8335046362_1da505d7d9_z.jpg

[MC.Understeer]

gotcha, well im in the market for a cage builder. If you know anyone that can do it please pass me their info. I have all the materials but no bender or decent welder.

One more pic to stay on topic with your build.


You're better off getting a pre bent kit online and adding to it. Otherwise you're gonna spend tons of money for someone to do everything by hand. We're getting a tubing bender at my shop to do a new tube front end on my car and Nikolays FD car. Id make my own cage out of raw materials but id rather get a basic kit then add to it. Im running out of time as is. I don't want to spend more house bending tubing and measuring ect...

[driftlife.son]

picked up 16 18x9.5 drift spares for a good deal, tires are on the way, also getting a tire machine and balancer tomorrow. Good stuff to have in this motorsports.
http://i47.tinypic.com/2mdmpn9.jpg

my vems standalone ecu's i ordered came in 3 days all the way from europe. Great system, tons of options to select from when ordering the unit. Ordered a unit with dual egt inputs, 4 bar map, sd card slot for data logging. What sold me on these units is vvti control, nitrous control, internal wideband output, o2 correction and of course price! Ordered 2 units and 4 sets of plugs so instead of having 4 cars with ecu's i can swap ecu's into different cars and just switch maps! Not gonna drive 4 cars at once anyways!
http://i47.tinypic.com/fqmwl.jpg


what wheels are these????

[PureRush]

what wheels are these????

+1 I would like to know too

[MC.Understeer]

+1 I would like to know too

Redline wheels. Cheap enough I bought 16 at half the cost of my CCW's

[MC.Understeer]

Bought a smaller 2nd turbo for drifting GT4082 1.18 a/r
http://i48.tinypic.com/w059qb.jpg

[EvoVIII808]

You're better off getting a pre bent kit online and adding to it. Otherwise you're gonna spend tons of money for someone to do everything by hand. We're getting a tubing bender at my shop to do a new tube front end on my car and Nikolays FD car. Id make my own cage out of raw materials but id rather get a basic kit then add to it. Im running out of time as is. I don't want to spend more house bending tubing and measuring ect...

agh that sucks. guess i have alot of tube for sale then. lol maybe i should just pick up a bender and knock it out myself.. welp thanks for the input and keep updating this build!

[richmond82]

so sweet buddy ! keep up the g w

[MC.Understeer]

Finally finished my turbo manifold, now that I've done one I know what id do differently next time. Still happy with it.
http://i46.tinypic.com/t97ewp.jpg

[future]

Looks amazing man

[conrad_s13.5]

fuck me,..im doing so many things wrong

[MC.Understeer]

Exedy twin, Arp flywheel bolts mounted
http://i48.tinypic.com/2hrlt3n.jpg

Got my Marlin Crawler race spec trans back, almost ready to drop it in as soon as I free up a Sti project off my lift
http://i49.tinypic.com/wtzvwp.jpg

[d_nice]

project is better with all the upgrade now i see

[Extreme Dimensions]

Jesus this is a beautiful motor! Keep up the work and super jealous of the skyline.

[Biggamehit]

good work man

[MC.Understeer]

Jesus this is a beautiful motor! Keep up the work and super jealous of the skyline.

Thanks! I was actually just down at extreme dimensions from Seattle about 3 weeks ago buying a bunch of s13 and s15 aero parts! This Skyline is prolly the least nicest one I've owned out of the 5 I've had.

[MC.Understeer]

Andd she's in!
http://i49.tinypic.com/14dzfb8.jpg

[EvoVIII808]

tightfit!:wackit::wackit::faint:

[MC.Understeer]

Cut some wires out of the harness lol
http://i46.tinypic.com/313ol8k.jpg
Got her all wired up pretty quick, just need to make it look all nice and tucked away.
http://i48.tinypic.com/33xelb4.jpg
Need to figure out which turbo I want to use :P
http://i47.tinypic.com/2wrp1ub.jpg

[d_nice]

^^^^^holy macro batman................

[JohanM]

pretty stoke on this thing man, how bad was taking all the unnecessary wires out, i just got my vvti too and going to start tearing the thing apart.

[MC.Understeer]

pretty stoke on this thing man, how bad was taking all the unnecessary wires out, i just got my vvti too and going to start tearing the thing apart.


I just marked all the plugs that im not going to need before I pulled the wiring off the motor and then cut everything open and cut each wire out one by one. Pretty easy, doesn't take much to run the motor. Most of the wires are for injectors and coil packs. Pretty basic, luckly I have my lower harness wired in from my RB so I just need to connect it to the 2jz starter and all my gauges are aftermarket including my apexi tach.

[JohanM]

I just marked all the plugs that im not going to need before I pulled the wiring off the motor and then cut everything open and cut each wire out one by one. Pretty easy, doesn't take much to run the motor. Most of the wires are for injectors and coil packs. Pretty basic, luckly I have my lower harness wired in from my RB so I just need to connect it to the 2jz starter and all my gauges are aftermarket including my apexi tach.

Oh ok, I saw some where that when keeping the twins that you can't remove any of the sensors on that side of the engine, so for now I will have to deal with all that.
I'm also running all aftermarket gauges and my own custom relay/fuse box and rewired the whole car with what I need, so that should make it easier to wire the engine up.

Quick question
What are you doing with the coolant line at the back of the head that goes up( not the one that goes across right on top of the trans)?

[MC.Understeer]

Oh ok, I saw some where that when keeping the twins that you can't remove any of the sensors on that side of the engine, so for now I will have to deal with all that.
I'm also running all aftermarket gauges and my own custom relay/fuse box and rewired the whole car with what I need, so that should make it easier to wire the engine up.

Quick question
What are you doing with the coolant line at the back of the head that goes up( not the one that goes across right on top of the trans)?


Yeah im not using the twins so I don't need any of those solenoids. Im not sure about that line as im not running a heater box/core. Still need to look into it. Id like to block it off but not if its going to cause any cooling issues...

[JohanM]

yeah i was going to bite the bullet and go single right away, but the budget is getting tighter as i'am almost done with the car.

i looked a little more today and found most people loop the hose from the head to under the second turbo, im going to keep looking to see if blocking them off will affect anything.

[MC.Understeer]

Tonight I got every last extra bit of wiring that's not needed and started making what I will need all pretty :)
http://i50.tinypic.com/1o52cl.jpg
My custom wiring harness building skills lol
http://i48.tinypic.com/30rxyso.jpg
I have the injector harness made also but its at work, just need to wire up my coilpack harness and install the wires into the ecu plugs for my standalone.

[MC.Understeer]

yeah i was going to bite the bullet and go single right away, but the budget is getting tighter as i'am almost done with the car.

i looked a little more today and found most people loop the hose from the head to under the second turbo, im going to keep looking to see if blocking them off will affect anything.


I did a bit of research and most people loop it. You CAN block it but it does make sense to keep the coolant flowing better in the engine. Think im gonna loop mine but with -an fittings.

[MC.Understeer]

Made some offset tension rod spacers for more angle!
http://i46.tinypic.com/xa7mr.jpg
Also made sway bar mount spacers to clear the oil pan if I end up running a front sway bar with my stiff spring rates. I want to be able to atleast drive the car both ways to see how it drives.
http://i50.tinypic.com/2yni788.jpg
Also made some motor mounts out of poly to the height id like the engine at.
http://i48.tinypic.com/i513dg.jpg

[JohanM]

nice update!
I did a mod on the circuit sports flca by moving the mounting point for the tension rod down to clear more angle, but the tire still like a 1/8" away from it when i hit full lock, so might have to make something like this for my tension rods.

[MC.Understeer]

nice update!
I did a mod on the circuit sports flca by moving the mounting point for the tension rod down to clear more angle, but the tire still like a 1/8" away from it when i hit full lock, so might have to make something like this for my tension rods.

I use to hit sway bar and tension rod but I had a pretty good size tanabe sway bar and Drift line tension rods witch have a big 1.5" hex to them and my rim would touch but before I had 18x10.5 with -0 offset. Going narrower wheels also.

[MC.Understeer]

Removed more wires from the interior harness.
http://i50.tinypic.com/21k9no7.jpg
http://i47.tinypic.com/zl21b5.jpg
Bored waiting for a ton of parts to come in since I just sold my s14 to put more money into the car so I had some stickers to install.
http://i48.tinypic.com/34qjqj9.jpg
http://i49.tinypic.com/2a7wsir.jpg

[zane]

Ultra bad ass. The hello kitty kills me haha. Looks like it's coming along nicely, I've got to start yanking my interior harness wires out as well, just no time.
Keep it up.

[MC.Understeer]

Went ahead with my crazy idea to run external dumps out through my hood lol.. hope the flames don't cause issues.
http://i47.tinypic.com/2i8wxhu.jpg

[MC.Understeer]

UPDATE!
MORE PARTS YAYYYYY!
http://i50.tinypic.com/2nixuz9.jpg
Yes that downpipe and exhaust look huge because it is lol 4"

My first JDM chop weld attempt..
http://i50.tinypic.com/qso20g.jpg

Mehhhh test fit? ....Really like MY idea of going out the nose between the headlights like its spitting flames out its nose O . . O
http://i45.tinypic.com/51bleb.jpg

And ive officially turned my work aka Subaru shop into a Nissan shop
http://i50.tinypic.com/2j2jdc8.jpg
http://i50.tinypic.com/scxaub.jpg

[ShadowMan]

I love it. But flames coming out the nose sounds even better, if only to see what it would look like. I like builds that have fun. I love lamp, too.

[EvoVIII808]

saw the white skyline yesterday, in Mt.V on my way back from seattle. Baller pipes!! reminds me of the white s14 in arizona.

[MC.Understeer]

4" downpipe tweaked and fitted
http://i48.tinypic.com/2jer62t.jpg
http://i49.tinypic.com/4kjp0x.jpg

[PG BOOSTED]

Picked up 16 18x9.5 drift spares for a good deal, tires are on the way, also getting a tire machine and balancer tomorrow. Good stuff to have in this motorsports.
http://i47.tinypic.com/2mdmpn9.jpg

My VEMS standalone ecu's I ordered came in 3 days all the way from Europe. Great system, tons of options to select from when ordering the unit. Ordered a unit with dual EGT inputs, 4 bar map, SD card slot for data logging. What sold me on these units is vvti control, nitrous control, internal wideband output, o2 correction and of course price! Ordered 2 units and 4 sets of plugs so instead of having 4 cars with ecu's I can swap ecu's into different cars and just switch maps! Not gonna drive 4 cars at once anyways!
http://i47.tinypic.com/fqmwl.jpg
You mind PMing me the website you got this standalone from?

[1988montecarloss]

You registered it federally under the canadian 17 digit vin? or 12 still from japan

x2

care to elaborate on this?

i only live 3hrs from canada, so thats why im wondering:naughty:

[DallasTXjdm]

F'n sweet!! Cannot wait to see her finished up!!

[Kwolfe]

Sweet build, 2jz awesomeness.

[MC.Understeer]

Did some rack modding..
http://i46.tinypic.com/hvqpep.jpg
http://i50.tinypic.com/msly0k.jpg
And slowly getting there.
http://i47.tinypic.com/2dmauxd.jpg

[sexcii-zenki]

Dayum i cant wait to see thos run!

[MC.Understeer]

Finally starting to look like a car, final test fit of parts before I send out stuff to get mirror polished. Also ordered a bunch more parts, purple samco hoses, going to do 1 piece branded brake lines from the master to the calipers re-routed under the engine and same with the clutch line.

http://i48.tinypic.com/23k5agn.jpg

[MC.Understeer]

Finally took some proper pics of my build in its current state

http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-1_zps4786f50e.jpg
http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-2_zps302dcc64.jpg
http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-3_zpsdb21f4ba.jpg
http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-4_zps31d1b16d.jpg
http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-5_zps8e963318.jpg
http://i49.photobucket.com/albums/f286/vr_sex/jeff-build-take-6_zps35d887e5.jpg

[uaserge]

Damn.

Sent from my MB855 using Tapatalk 2

[JohanM]

So sick!!!

[Biggamehit]

good work man

[Boss_S14]

updates needed on this!!

[bc.]

Sick!

Sent from my banana phone using BananApp

[MC.Understeer]

Can anyone spy my new mod?
http://i49.photobucket.com/albums/f286/vr_sex/09571b55-fcc5-43fa-adab-2c71814c49dd_zpsc2fb86bd.jpg

[cbcm2435]

do it:bigok:

[PG BOOSTED]

I see it! very nice

[BiG MiKE86]

...is that a supercharger? OmG...

[jdm2191]

I want to really see how that turns out

[MC.Understeer]

Been really slacking on working on the car the last month but this week ive been busting ass because I have back to back events coming up in a week and a half so I need to get it running and ready to go. As of today this is where im at with the car and im very close to starting her up.
http://i46.tinypic.com/28h0iyt.jpg
Picked up a new seat since my old ones had expired FIA tags
http://i48.tinypic.com/fd9186.jpg
picked up some new front brakes for a really good deal :)
http://i45.tinypic.com/2jahwuv.jpg
S13 rotor compared to the new 15" rotor
http://i50.tinypic.com/2uotbw2.jpg
Tons of clearance in a 18" wheel
http://i46.tinypic.com/ocis5.jpg
Brackets to make them fit
http://i50.tinypic.com/8vyi9z.jpg
http://i46.tinypic.com/10rv1p3.jpg

[collegekid]

What brakes are they I've never seen them?

[E's factory mx83]

Look like corvette's bbk

[taeisbeast]

This an awesome freaking build man.

Keep it up.

[Flicktitty]

I'm assuming the S/C pic was just for shits and giggles?

Is that just an ebay Greddy Intake manifold Repica? If so how is the fitment by the brake booster?

[jk26]

What brakes are they I've never seen them?


CTS-V im pretty sure

[MC.Understeer]

I'm assuming the S/C pic was just for shits and giggles?

Is that just an ebay Greddy Intake manifold Repica? If so how is the fitment by the brake booster?


Supercharger is not for shits and giggles. I have it ready to go minus the charge pipe situation. Im going to break in the motor on low boost with just the turbo and do some testing with it and then deal with the supercharger project on its own. Right now I have 30 different things to deal with the swap but I think she'll be ready to fire up for the first time tomorrow after the ecu gets all setup and the firmware up to date.

Brakes are 2012 CTS-V 6 pistons from the newer awd models.

[MC.Understeer]

Finally got her running. Having crank signal errors not allowing me to rev past 5300 but im sure its due to the weak quick crank sensor bracket I made. Going to redo the bracket to reduce and movement or bad harmonics.
http://i49.photobucket.com/albums/f286/vr_sex/919635_10200195070053137_2060129601_o_zps1cb3a75f. jpg (http://s49.photobucket.com/user/vr_sex/media/919635_10200195070053137_2060129601_o_zps1cb3a75f. jpg.html)
http://i49.photobucket.com/albums/f286/vr_sex/934121_4715109077319_546028596_n_zps014062c3.jpg (http://s49.photobucket.com/user/vr_sex/media/934121_4715109077319_546028596_n_zps014062c3.jpg.h tml)


http://i49.photobucket.com/albums/f286/vr_sex/IMG_20130422_093337_zps309ffb0a.jpg


2jz pink beast #2 - YouTube (http://www.youtube.com/watch?v=BK3r2csrQeI)

[MC.Understeer]

Little Dyno video. Still working out some bugs, crank sensors keep failing so finally im going with an Oem sensor instead of an aftermarket oem replacement. Im 99% positive its why im getting high rpm miss along with my ID1000's and fuel pump maxing out at 550whp/600wtq 22psi. I'm pretty happy since im running wasted spark (3 oem aristo Is300 style coilpacks) VVT-i is also not hooked up yet either.


Jeff Woodruff - 2JZ DYNO - GCMedia - YouTube (http://youtu.be/5mzNdozktZs)

[EvoVIII808]

Nice! you going to be at open drift this weekend??

[MC.Understeer]

Nice! you going to be at open drift this weekend??

Maybe. I'll be at the grassroots event Sunday I hope.

[MC.Understeer]

Thought I'd update my build thread a little now that I'm close to getting twards the end of finishing everything including repainting the front end.
http://i49.photobucket.com/albums/f286/vr_sex/1000493_599426880088035_539983306_n_zpsc9285bd7.jp g (http://s49.photobucket.com/user/vr_sex/media/1000493_599426880088035_539983306_n_zpsc9285bd7.jp g.html)
http://i49.photobucket.com/albums/f286/vr_sex/1048861_599452670085456_2046191266_o_zps98dc879c.j pg (http://s49.photobucket.com/user/vr_sex/media/1048861_599452670085456_2046191266_o_zps98dc879c.j pg.html)
http://i49.photobucket.com/albums/f286/vr_sex/1014645_599509723413084_2117804649_o_zps19c6d4ee.j pg (http://s49.photobucket.com/user/vr_sex/media/1014645_599509723413084_2117804649_o_zps19c6d4ee.j pg.html)
http://i49.photobucket.com/albums/f286/vr_sex/1014886_603114363052620_893481941_o_zps1f740e39.jp g (http://s49.photobucket.com/user/vr_sex/media/1014886_603114363052620_893481941_o_zps1f740e39.jp g.html)
In action...sorta.
Jeff Woodruff 2jzgte EVD 100 Evergreen drift S13.5 - YouTube (http://youtu.be/1Jpq_jqKxBs)

[driftlife.son]

can i pay you to reproduce those brackets to fit the cts-v brakes

[MC.Understeer]

can i pay you to reproduce those brackets to fit the cts-v brakes

for the 4 or 6 piston?

[driftlife.son]

for the 4 or 6 piston?

preferably the 6 piston but i dont mind the 4 either. and what rotor did you use as well

[MC.Understeer]

preferably the 6 piston but i dont mind the 4 either. and what rotor did you use as well

They already make a 4 piston caliper bracket you can get through chase bays. These ones have to have tubular LCA's or the calipers will hit the stock control arm even with roll center correction ball joints. I'm using the infinity FX50 front rotors.

[MC.Understeer]

Some action from this weekends event
Jeff Woodruff 2jz Evergreen drift EVD 102 - YouTube (http://www.youtube.com/watch?v=oSLHv74Ckaw)
Jeff Woodruff Evergreen drift EVD 101 2jz s13.5 - YouTube (http://www.youtube.com/watch?v=l9UwIFGnXtA)
http://i49.photobucket.com/albums/f286/vr_sex/facebook_-168463495_zpsbd4d698f.jpg (http://s49.photobucket.com/user/vr_sex/media/facebook_-168463495_zpsbd4d698f.jpg.html)

[JohanM]

glad to to see you out there man, i my self finally finish mine and went to my second event this past weekend, motor feels great with the twins.

is it still cutting out at 5,300 rpms?

[MC.Understeer]

glad to to see you out there man, i my self finally finish mine and went to my second event this past weekend, motor feels great with the twins.

is it still cutting out at 5,300 rpms?

No its fine now, I had to mess with resistors in line of the crank position sensor. Was getting too much noise in the signal.