FL Huge SR Partout HKS, Greddy, Apexi, CS, OEM Almost all new - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

92RMS13 · 07-28-2010, 07:44 PM

UPDATED!!!

All parts are new except where noted, parts are available for local pickup, can ship at buyers expense, payment - Cash, Postal Money Order, or Paypal, if paypal please include 3% fee.

SR20DET Longblock, started as good running kouki S13 engine, reassembled with ACL race bearings rod/main/thrust, Mazworx head stud kit, Cosworth MHG, Tomei 256 Poncams, S14 Oil pickup, RAS, Block and head both hot tanked and decked, S14 Water pump, Enjuku Racing exhaust manifold stud/nut kit, new oem valve cover studs, will include bare intake manifold-no electronics, and valve cover.

$2100

Garrett GT2871R, 52Trim "28R" style compressor housing, exhaust housing is .64a/r and has been ceramic coated, includes stainless studs and nuts on exhaust outlet side and new studs for compressor inlet, as well as oil drain kit. $1150

Circuit Sports billet aluminum fuel rail $150

Dif "forged" turbo lines $150

E5 Ecu, tuned for 740cc injectors and Zmaf by RSEnthalpy $400

HKS 740cc Injectors, new except for now having O-rings installed on them. $500

Blitz SE FMIC S13 Kit, $490

Fidanza aluminum flywheel with ACT 6 puck sprung clutch kit, includes new act throwout bearing, was installed and broken in, an awesome setup $450

Apexi pen type turbo timer with CS harness $100

Greddy aluminum oil pan $340

Flex-A-Lite Dual 12" puller fan setup $275

Enjuku Racing hotpipe with greddy type RS BOV $250

Hotpipe for Greddy bov, one pictured above with no bov $40

Greddy "suction kit" for installing T28 with Z32 maf into S13 with no poor fitment, everything but the foamie filter $220

Dakota Digital Electronic fan controller $120

New Nabco slave cylinder $20

SR Coil Pack Harness $20

New OEM Thermostat $20

OEM Z32 MAF, almost new $100

SR CAS $100

New ECU Coolant Temp Sensor $20

New OEM Fat Oxygen Sensor $80

SR Ignitor $80

SR TPS $50

SR Coil Pack set $85

Turbo locking tabs: 2 SOLD, 2 left $10

Stock T25 inlet/outlet elbows $20

Bando SR belt set, ac, alt/wp, ps $30

OEM exhaust manifold gasket $5

duynguyenn240 · 07-28-2010, 09:05 PM

ill take the greddy oil cap $35 shipped to 76014 pm me your paypal ?

240Zfunahollic · 07-28-2010, 09:53 PM

pm'd msglngth

1gr8bar10der · 07-28-2010, 11:46 PM

I also PM'd you on TR about some parts. Can pick it up as soon as tomorrow. LMK

240ND · 07-29-2010, 12:08 AM

how much for the DSS driveshaft shipped to 58701? I can paypal anytime and need that driveshaft!
shoot me a pm thanks!

duynguyenn240 · 07-29-2010, 12:22 AM

money send for the oil cap thanks

Hyphymode · 07-29-2010, 12:23 AM

pm about clutch/flywheel kit and greddy oil cap. Need asap.

chituntang · 07-29-2010, 01:52 PM

Dif stainless clutch hose $20
New OEM exhaust manifold nuts and spacers $25
Turbo to manifold gaskets $10
Turbo Hardware Assortment, 7 studs, 10 copper locking nuts, 2 stainless nuts $30
Turbo outlet gasket $10
Turbo locking tabs $20 for all 4 ($10 for 2?)
Fuel rail to intake manifold orings $15
New OEM PCV Valve $10

Maybe interested:
Nismo Clutch Fork Pivot $25
Greddy Oil Cap $35

Shipping to GA,30044. Will buy the interested parts if we can make a good deal.
Can I get the gasket that you have form the 2871R your are selling?

92RMS13 · 07-31-2010, 04:27 PM

BUMP #1

need this stuff gone!

hulkster_s13 · 08-14-2010, 03:09 AM

ill take the hotpipe w/o bov with flange if you still got it. pm shipped to 96744 and paypal

vqboodah · 08-17-2010, 03:02 PM

how many miles have you put on it?

*handinpants* · 08-25-2010, 02:28 AM

whats up with the inkectors

penco · 08-25-2010, 05:47 AM

Could you update it with the parts that were sold..im interested in a few things.

*racerx2k1* · 08-25-2010, 08:04 AM

Last Activity: 08-15-2010 10:18 PM

07-28-2010, 09:53 PM	#3
240Zfunahollic Zilvia Junkie Join Date: Aug 2003 Location: South Carolina Age: 35 Posts: 593 Trader Rating: (35) Feedback Score: 35 reviews	pm'd msglngth __________________ Visit My Trader rating page http://zilvia.net/f/traderratings.html?u=15347

08-17-2010, 03:02 PM	#11
vqboodah Zilvia Addict Join Date: Apr 2006 Location: MA Posts: 601 Trader Rating: (20) Feedback Score: 20 reviews	how many miles have you put on it? Last edited by vqboodah; 08-17-2010 at 10:30 PM..

08-25-2010, 02:28 AM	#12
handinpants FreshColdBeer.com Join Date: Feb 2008 Location: California Age: 38 Posts: 2,665 Trader Rating: (48) Rides Gallery: handinpants Feedback Score: 48 reviews	whats up with the inkectors __________________

08-25-2010, 08:04 AM	#14
racerx2k1 460 Join Date: Jan 2004 Location: Nowhere Posts: 17,704 Trader Rating: (0) Feedback Score: 0 reviews	Last Activity: 08-15-2010 10:18 PM __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-28-2010, 07:44 PM	#1
92RMS13 Leaky Injector Join Date: Sep 2009 Location: Tampa, Fl Age: 31 Posts: 135 Trader Rating: (13) Feedback Score: 13 reviews	Huge SR Partout HKS, Greddy, Apexi, CS, OEM Almost all new UPDATED!!! All parts are new except where noted, parts are available for local pickup, can ship at buyers expense, payment - Cash, Postal Money Order, or Paypal, if paypal please include 3% fee. SR20DET Longblock, started as good running kouki S13 engine, reassembled with ACL race bearings rod/main/thrust, Mazworx head stud kit, Cosworth MHG, Tomei 256 Poncams, S14 Oil pickup, RAS, Block and head both hot tanked and decked, S14 Water pump, Enjuku Racing exhaust manifold stud/nut kit, new oem valve cover studs, will include bare intake manifold-no electronics, and valve cover. $2100 Garrett GT2871R, 52Trim "28R" style compressor housing, exhaust housing is .64a/r and has been ceramic coated, includes stainless studs and nuts on exhaust outlet side and new studs for compressor inlet, as well as oil drain kit. $1150 Circuit Sports billet aluminum fuel rail $150 Dif "forged" turbo lines $150 E5 Ecu, tuned for 740cc injectors and Zmaf by RSEnthalpy $400 HKS 740cc Injectors, new except for now having O-rings installed on them. $500 Blitz SE FMIC S13 Kit, $490 Fidanza aluminum flywheel with ACT 6 puck sprung clutch kit, includes new act throwout bearing, was installed and broken in, an awesome setup $450 Apexi pen type turbo timer with CS harness $100 Greddy aluminum oil pan $340 Flex-A-Lite Dual 12" puller fan setup $275 Enjuku Racing hotpipe with greddy type RS BOV $250 Hotpipe for Greddy bov, one pictured above with no bov $40 Greddy "suction kit" for installing T28 with Z32 maf into S13 with no poor fitment, everything but the foamie filter $220 Dakota Digital Electronic fan controller $120 New Nabco slave cylinder $20 SR Coil Pack Harness $20 New OEM Thermostat $20 OEM Z32 MAF, almost new $100 SR CAS $100 New ECU Coolant Temp Sensor $20 New OEM Fat Oxygen Sensor $80 SR Ignitor $80 SR TPS $50 SR Coil Pack set $85 Turbo locking tabs: 2 SOLD, 2 left $10 Stock T25 inlet/outlet elbows $20 Bando SR belt set, ac, alt/wp, ps $30 OEM exhaust manifold gasket $5 Last edited by 92RMS13; 07-31-2010 at 04:26 PM..

07-28-2010, 09:05 PM	#2
duynguyenn240 Leaky Injector Join Date: Dec 2007 Location: arlington Age: 32 Posts: 143 Trader Rating: (6) Feedback Score: 6 reviews	ill take the greddy oil cap $35 shipped to 76014 pm me your paypal ?

07-28-2010, 11:46 PM	#4
1gr8bar10der Post Whore! Join Date: Aug 2009 Location: Tampa/Bangkok Posts: 3,431 Trader Rating: (77) Feedback Score: 77 reviews	I also PM'd you on TR about some parts. Can pick it up as soon as tomorrow. LMK

07-29-2010, 12:08 AM	#5
240ND Leaky Injector Join Date: Jun 2009 Location: North Dakota Age: 30 Posts: 120 Trader Rating: (4) Feedback Score: 4 reviews	how much for the DSS driveshaft shipped to 58701? I can paypal anytime and need that driveshaft! shoot me a pm thanks!

07-29-2010, 12:22 AM	#6
duynguyenn240 Leaky Injector Join Date: Dec 2007 Location: arlington Age: 32 Posts: 143 Trader Rating: (6) Feedback Score: 6 reviews	money send for the oil cap thanks

07-29-2010, 12:23 AM	#7
Hyphymode Leaky Injector Join Date: Mar 2009 Location: Las Vegas Posts: 62 Trader Rating: (3) Feedback Score: 3 reviews	pm about clutch/flywheel kit and greddy oil cap. Need asap.

07-29-2010, 01:52 PM	#8
chituntang Zilvia Junkie Join Date: Sep 2005 Location: ATL Age: 35 Posts: 505 Trader Rating: (13) Feedback Score: 13 reviews	Dif stainless clutch hose $20 New OEM exhaust manifold nuts and spacers $25 Turbo to manifold gaskets $10 Turbo Hardware Assortment, 7 studs, 10 copper locking nuts, 2 stainless nuts $30 Turbo outlet gasket $10 Turbo locking tabs $20 for all 4 ($10 for 2?) Fuel rail to intake manifold orings $15 New OEM PCV Valve $10 Maybe interested: Nismo Clutch Fork Pivot $25 Greddy Oil Cap $35 Shipping to GA,30044. Will buy the interested parts if we can make a good deal. Can I get the gasket that you have form the 2871R your are selling?

07-31-2010, 04:27 PM	#9
92RMS13 Leaky Injector Join Date: Sep 2009 Location: Tampa, Fl Age: 31 Posts: 135 Trader Rating: (13) Feedback Score: 13 reviews	BUMP #1 need this stuff gone!

08-14-2010, 03:09 AM	#10
hulkster_s13 Zilvia Member Join Date: Nov 2005 Location: down by da beach Posts: 276 Trader Rating: (9) Feedback Score: 9 reviews	ill take the hotpipe w/o bov with flange if you still got it. pm shipped to 96744 and paypal

08-25-2010, 05:47 AM	#13
penco Zilvia Member Join Date: Feb 2008 Location: Milwaukee Age: 36 Posts: 248 Trader Rating: (1) Feedback Score: 1 reviews	Could you update it with the parts that were sold..im interested in a few things.