Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 04-06-2019, 07:16 PM   #1
Albeeeeert
 
Join Date: Apr 2019
Location: North Carolina
Age: 23
Posts: 4
Trader Rating: (0)
Albeeeeert is an unknown quantity at this point
Feedback Score: 0 reviews
S13, 300zx NA VLSD, Questions Before Install

Hey everyone I recently acquired a 1991 Nissan 240sx Hatch. The previous owner installed a welded diff in hopes of drifting I assume. I despise it, I use the car as a weekend cruiser and have plans to maybe track it or autocross it in the future.

With these aspirations for the car I decided to pick up a factory VLSD, and was lucky enough to find a 1992 NA 300zx VLSD at a local junkyard. This differential has different output shaft flanges (right word?) than the 240sx as I was expecting. My plan was to get 96+ J30 output shafts but as I now have a distaste for pulling differentials I've decided to just get new axles. The old ones have probably been ravaged by the welded diff anyways.

My searches have pointed me to 93 J30 axles, but when looking at them on part store websites I notice the driver and passenger side are different lengths and it worries me. This is why I didn't get 300zx axles; apparently the passenger side is too long. Everyone says to use J30 axles, but don't specify if I'm using both sides in their corresponding location or something wild like two driver side axles. Yes it's a dumb question, but I'd just like some assurance before spending the money on axles that I'm not 100% sure will work.

While I have everyone's attention, I have a quick question about the front mounts on the differential. The S13 diff seems to either have no bushings or a lot smaller bushings, whereas the Z32 diff has large holes with a bushing. Is this something I should worry about, buy a solid bushing, or just install and forget about?

I appreciate everyone's time, knowledge, and patience!
Albeeeeert is offline   Reply With Quote
Sponsored Links
Old 04-29-2019, 09:00 AM   #2
Atill93
Leaky Injector
 
Join Date: Jul 2012
Location: Alabama
Age: 28
Posts: 144
Trader Rating: (0)
Atill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-known
Feedback Score: 0 reviews
I've been trying to find a proper axle/differential setup for years and just purchased some new axles from O'Reillys last week and installed them over the weekend.

You're correct, the driver and passenger axles are different lengths.

There are two important measurements that can help reassure you that you might be getting the right axles:
1. measure the length of the axles
2. count the number of splines on the end that slides into the hub

and obviously make sure you get the correct bolt pattern (usually 5 or 6 bolts) to match up to the output shafts of the differential

here's a picture for reference



I actually had to order axles for a 93 infiniti j30 to fit the diff that I put in my s13 but they fit perfectly

good luck!
Atill93 is offline   Reply With Quote
Old 04-29-2019, 10:18 AM   #3
Albeeeeert
 
Join Date: Apr 2019
Location: North Carolina
Age: 23
Posts: 4
Trader Rating: (0)
Albeeeeert is an unknown quantity at this point
Feedback Score: 0 reviews
Thanks for your reply! It looks like I lucked out in that case because I just ordered 93 J30 axles
Albeeeeert is offline   Reply With Quote
Old 04-29-2019, 10:34 AM   #4
Atill93
Leaky Injector
 
Join Date: Jul 2012
Location: Alabama
Age: 28
Posts: 144
Trader Rating: (0)
Atill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-knownAtill93 is making his/her stupidity well-known
Feedback Score: 0 reviews
No problem. Nice!
Atill93 is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:24 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™