Another S13 owner with idle problems... - Page 2 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

lilrookz · 07-30-2012, 12:22 AM

I think its in the timing. Not 100% sure on this, I also have a 89' 240 with ka24de and somedays for a couple days or so in a row it will run like complete ass. Idling around 400-800 sometimes it stalls out, sometimes when I give it gas it hesitates. Its done this for as long as I've had the swap.

rbsidewayz · 08-02-2012, 01:12 AM

Quote:

Originally Posted by Hanz41

i have this exact problem as well on my sr.. the car jumps around from like 1000-1600 rpms and keeps going for like 30 seconds then finally settles.. my car died 3 different times on me today at stop lights.... also my car was hesitating at like 2500 rpms when given a little bit of throttle.. like it would start pulling then hesitate for s split second... ill check the mafs for the idle problem but idk wat to do about the sputterness.. i was gonna make a new thread until i saw this so i just wanted to post here

spark plugs

silvia_slider · 08-07-2012, 03:18 AM

im having the same problem, i have a seprate thread so check it out if you can help cheers

http://zilvia.net/f/s-chassis/469716...ease-help.html

silvia_slider · 08-07-2012, 03:20 AM

im having same problem any help would be great!

http://zilvia.net/f/s-chassis/469716...ease-help.html

Keenang · 08-09-2012, 10:20 PM

Almost the same problem any help would be well appreciated http://zilvia.net/f/engine-tech/4700...ml#post4844355

1fastser · 12-03-2012, 09:11 PM

Do you have an update on this?

mr2gons14 · 12-04-2012, 04:17 AM

check ur plug gap with sputtery boost, idle and accel sputtery check ur injectors for leaks (happened to me), check ur maf especially is u upgraded to z32 remember to have a good chassis ground or ull have issues. Checking your timing cant help rent a timing gun from checkers if u dont have access to one

Flako · 12-04-2012, 06:30 AM

My idle issues all were related to vacuum hoses. Its best to replace those.

mr2gons14 · 12-04-2012, 09:23 AM

I was under the impression everyone had a boost/ vac gauge is reccomend one and have an extra if anyone is in need

Con-city_s13 · 12-17-2012, 07:31 PM

Same problem with my KA. Pulled hard and ran fine normally. I found a tiny vacuum line on the back-left side of the engine that had torn. I replaced the line a few months ago and haven't had a problem since. My onboard diagnostic system never threw a code and I did the usual cleaning and unpluging various sensors, etc.

Bottom line, KA's have tons of vacuum lines and they're all old. There's bound to be a leak somewhere.

TypeXFan · 12-25-2012, 12:34 PM

Just wanted to update an OLD thread, havent been on the forums for a while. I had done a full replacement on the vacuum lines and still had the problems, for a long time I had no other solutions. My only other conclusion was that I may have a bad harness. So I took the spare harness I had, sodered on new plugs where they were bad, heat wrapped sensitive areas, was a new and better harness ready to swap in. So while removing my old harness I spotted a fuel line that was pinched in a area that would not have been visible to me if I had not removed the harness. Fixed the pinched line and put in the new harness, and the car runs smooth as hell with a perfect 700 idle.

Took forever to figure it out, I reccomend that everyone checks their vacuum and fuel lines since these cars are 20(give or take) years old.

dkim1985 · 12-25-2012, 02:23 PM

Quote:

Originally Posted by TypeXFan

Just wanted to update an OLD thread, havent been on the forums for a while. I had done a full replacement on the vacuum lines and still had the problems, for a long time I had no other solutions. My only other conclusion was that I may have a bad harness. So I took the spare harness I had, sodered on new plugs where there were bad, heat wrapped sensitive areas, was a new and better harnes ready to swap in. So while removing my old harness I spotted a fuel line that was pinched in a area that would not have been visible to me if I had not removed the harness. Fixed the pinched line and put in the new harness, and the car runs smooth as hell with a perfect 700 idle.

Took forever to figure it out, I reccomend that everyone checks their vacuum and fuel lines since these cars are 20(give or take) years old.

sweet! congrats!
where was the pinch located at?

TypeXFan · 12-25-2012, 02:46 PM

Quote:

Originally Posted by dkim1985

sweet! congrats!
where was the pinch located at?

The line running below the fuel filter going down towards the chasis.

12-04-2012, 04:17 AM	#37
mr2gons14 Zilvia Addict Join Date: Jun 2011 Location: Phoenix, AZ Age: 30 Posts: 639 Trader Rating: (7) Feedback Score: 7 reviews	check ur plug gap with sputtery boost, idle and accel sputtery check ur injectors for leaks (happened to me), check ur maf especially is u upgraded to z32 remember to have a good chassis ground or ull have issues. Checking your timing cant help rent a timing gun from checkers if u dont have access to one __________________ zilvia.net/f/cars-sale/517359-95-240sx-sr20-swap-uras-greddy-apexi-ect.html

12-04-2012, 09:23 AM	#39
mr2gons14 Zilvia Addict Join Date: Jun 2011 Location: Phoenix, AZ Age: 30 Posts: 639 Trader Rating: (7) Feedback Score: 7 reviews	I was under the impression everyone had a boost/ vac gauge is reccomend one and have an extra if anyone is in need __________________ zilvia.net/f/cars-sale/517359-95-240sx-sr20-swap-uras-greddy-apexi-ect.html

12-25-2012, 12:34 PM	#41
TypeXFan Leaky Injector Join Date: Jun 2010 Location: Fresno, CA Age: 39 Posts: 84 Trader Rating: (1) Feedback Score: 1 reviews	Just wanted to update an OLD thread, havent been on the forums for a while. I had done a full replacement on the vacuum lines and still had the problems, for a long time I had no other solutions. My only other conclusion was that I may have a bad harness. So I took the spare harness I had, sodered on new plugs where they were bad, heat wrapped sensitive areas, was a new and better harness ready to swap in. So while removing my old harness I spotted a fuel line that was pinched in a area that would not have been visible to me if I had not removed the harness. Fixed the pinched line and put in the new harness, and the car runs smooth as hell with a perfect 700 idle. Took forever to figure it out, I reccomend that everyone checks their vacuum and fuel lines since these cars are 20(give or take) years old. Last edited by TypeXFan; 12-25-2012 at 02:50 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-30-2012, 12:22 AM	#31
lilrookz Leaky Injector Join Date: Aug 2011 Location: DFW, Texas Age: 31 Posts: 53 Trader Rating: (0) Feedback Score: 0 reviews	I think its in the timing. Not 100% sure on this, I also have a 89' 240 with ka24de and somedays for a couple days or so in a row it will run like complete ass. Idling around 400-800 sometimes it stalls out, sometimes when I give it gas it hesitates. Its done this for as long as I've had the swap.

08-07-2012, 03:18 AM	#33
silvia_slider Join Date: Mar 2011 Location: whangarei new zealand Posts: 4 Trader Rating: (0) Feedback Score: 0 reviews	im having the same problem, i have a seprate thread so check it out if you can help cheers http://zilvia.net/f/s-chassis/469716...ease-help.html

08-07-2012, 03:20 AM	#34
silvia_slider Join Date: Mar 2011 Location: whangarei new zealand Posts: 4 Trader Rating: (0) Feedback Score: 0 reviews	im having same problem any help would be great! http://zilvia.net/f/s-chassis/469716...ease-help.html

08-09-2012, 10:20 PM	#35
Keenang Leaky Injector Join Date: Jul 2012 Location: Greenville SC/ Fort stewart GA Posts: 71 Trader Rating: (1) Feedback Score: 1 reviews	Almost the same problem any help would be well appreciated http://zilvia.net/f/engine-tech/4700...ml#post4844355

12-03-2012, 09:11 PM	#36
1fastser Leaky Injector Join Date: Dec 2008 Location: Texas Posts: 125 Trader Rating: (2) Feedback Score: 2 reviews	Do you have an update on this?

12-04-2012, 06:30 AM	#38
Flako Leaky Injector Join Date: Nov 2011 Location: VA Posts: 77 Trader Rating: (0) Feedback Score: 0 reviews	My idle issues all were related to vacuum hoses. Its best to replace those.

12-17-2012, 07:31 PM	#40
Con-city_s13 Join Date: Jan 2012 Location: Concord, NC Posts: 43 Trader Rating: (0) Feedback Score: 0 reviews	Same problem with my KA. Pulled hard and ran fine normally. I found a tiny vacuum line on the back-left side of the engine that had torn. I replaced the line a few months ago and haven't had a problem since. My onboard diagnostic system never threw a code and I did the usual cleaning and unpluging various sensors, etc. Bottom line, KA's have tons of vacuum lines and they're all old. There's bound to be a leak somewhere.