engine/engine bay photos - Page 2 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

*fliprayzin240sx* · 12-01-2006, 01:43 PM

I actually miss working on that piece of shiet....

lucky7 · 12-02-2006, 12:51 PM

like 2 months ago. not much has changed...

the harness has been pulled... its being re-done. mother fuck.

*MELLO*SOS* · 12-05-2006, 11:39 AM

RB20DET.. One day it'll be done and installed, hopefully in Q1 2007. Still need a bazillion small things...

Here is a close up of the Injector "block offs" I used for intake manifold leak down test. Made from home depot supplies: 1/2" rubber stoppers & some shelving screws 3" long with 1/2" heads, worked great. Set #1 to TDC, use leak down tester threaded into cyl #3 to pressurize manifolds to 2 bar/30psi... Spray down RTV'd areas on lower & upper mani's with soapy water. Not shown is TB blockoff plate made from a 5"x5" smooth wooden peice, drilled for tb bolts & with an improvised RTV gasket to seal with.

driftstyre · 12-10-2006, 09:21 PM

I wish it was even remotely this clean still.

LXU55 · 12-10-2006, 09:32 PM

Just a few of my R32 with rb25 conversion and numerous other mod’s, functional more so then pretty looking

We had this S13 built about 5 years ago, rb25 conversion with lots of mod’s including custom Twin Turbo manifolds, made 600rwhp on C16 and laid down 10.8 @ 128mph.

The Australian’s on here should remember the magazine coverage on this car

zipman72 · 12-10-2006, 10:10 PM

kuramaya · 12-10-2006, 10:31 PM

Just like now except for the new APEXi Boost Sensor..

amplifi3d · 12-11-2006, 01:44 AM

my friends v mount

redsuns3838 · 12-11-2006, 05:23 PM

theres mine.. Pretty messy. Im not big into dressup but i admit it is nice to have a nice looking engine bay. I really need to clean it up but does anyone have any tips on where to start?

Im thinkin
1)golden eagle vac manifold
2)alumi intake pipe,
3)remove the ABS actuator and change over to non abs. have all the parts just no time.
4) relocate battery to trunk. have most of the hardware just need to pick up a circuit breaker
any other tips besides those?

Id like to relocate fusebox but I dont know if Im up for all that extending of wires =/

aNskY · 12-11-2006, 06:07 PM

guess ill play, not very impressive,,,,.

-=RS13=- · 12-15-2006, 10:53 PM

Well i will add. There is about 1 foot of snow up here so my cars not going anywhere. Its time for a good cleaning and then paint. No more abs and bracketry everwhere

This was it before a little dirty

Slidin240Wayz · 12-16-2006, 12:06 PM

My old kuruma.

Carlos

kuruptR · 12-16-2006, 01:01 PM

hard to see but only pic i got, s14 with tucked wiring harness

LookOut Nick · 12-18-2006, 12:22 PM

refill!

vrooompssssht · 12-18-2006, 02:24 PM

*holemilk00* · 12-18-2006, 03:56 PM

I know you're all jealous of my stockness. But concidering the dirt pile this car was when I bought it its in heaven now with me, plus its getting stripped down like a broke hooker the night before rents due right after christmas, finally got most of my stuff for the swap.

LukeDogg316 · 12-18-2006, 05:31 PM

This thread is awesome

here's my contribution

before

newer pic but still kinda old

dannysr20 · 12-18-2006, 05:49 PM

this is mine.

klattr1 · 01-01-2007, 02:45 AM

my ka-t:

rico05 · 01-01-2007, 10:25 AM

Dousan_PG · 01-01-2007, 01:04 PM

painted my IC piping and did some polishing
and im tired.
that is all for now

valve cover gets painted next week i think. sick of it being so bland and boring.
my engine looks like shit compared with everyone else's. too busy busy.

s13silady · 01-14-2007, 08:29 PM

got some more cleaning to do...its filthy.. but knowing me its probably gonna stay that way.

ni5mo240 · 01-14-2007, 10:57 PM

This is mine, looks stealthy with the factory airbox cut out with HKS drop in filter and GT2530 turbo on the stock manifold!

brainfood · 01-14-2007, 11:23 PM

stuntman240 · 01-18-2007, 03:43 PM

WhiteGLX · 01-19-2007, 01:20 PM

Original Swap

Rebuilt Motor

V-mount

Ducted V-Mount

xxchurroxx · 01-19-2007, 01:47 PM

liv2drift045 · 01-20-2007, 06:04 AM

i hope to do a v-mount setup on the cefiro when i go sr... only time will tell... here's the current trash pit

LookOut Nick · 01-25-2007, 12:54 PM

12-01-2006, 01:43 PM	#32
fliprayzin240sx Man w/ CTSV & a Car Seat Join Date: Aug 2002 Location: Tampa Posts: 17,998 Trader Rating: (19) Rides Gallery: fliprayzin240sx Feedback Score: 19 reviews	I actually miss working on that piece of shiet.... __________________ If you think Zilvia has too many assholes... CLICK HERE!!!

12-02-2006, 12:51 PM	#33
lucky7 Post Whore! Join Date: Mar 2005 Location: Oakland (OT) Michigan Age: 36 Posts: 3,353 Trader Rating: (0) Rides Gallery: lucky7 Feedback Score: 0 reviews	like 2 months ago. not much has changed... the harness has been pulled... its being re-done. mother fuck. __________________ -Dane

12-10-2006, 09:32 PM	#36
LXU55 Join Date: Dec 2006 Location: Australia Posts: 6 Trader Rating: (0) Feedback Score: 0 reviews	Just a few of my R32 with rb25 conversion and numerous other mod’s, functional more so then pretty looking We had this S13 built about 5 years ago, rb25 conversion with lots of mod’s including custom Twin Turbo manifolds, made 600rwhp on C16 and laid down 10.8 @ 128mph. The Australian’s on here should remember the magazine coverage on this car __________________ Past: 490rwhp super happy fun R32. Now: super happy slow LS400 I have a Nissan fetish! 2 x S13’s and 4 x R32’s down, time for another S13

12-10-2006, 10:10 PM	#37
zipman72 Leaky Injector Join Date: May 2006 Location: orange Posts: 62 Trader Rating: (0) Feedback Score: 0 reviews	__________________ I Give Up.

12-10-2006, 10:31 PM	#38
kuramaya Nissanaholic! Join Date: Dec 2004 Location: 沖縄 , Japan Age: 48 Posts: 1,677 Trader Rating: (1) Rides Gallery: kuramaya Feedback Score: 1 reviews	Just like now except for the new APEXi Boost Sensor.. __________________ ZEROYON WEBSITE IS HOMO NEW SITE: blacklinux.com/innersanctum/index.php

12-01-2006, 11:43 AM	#31
TokyoNights Zilvia FREAK! Join Date: Dec 2002 Location: garage Age: 38 Posts: 1,215 Trader Rating: (2) Rides Gallery: TokyoNights Feedback Score: 2 reviews

12-05-2006, 11:39 AM	#34
MELLOSOS* LAID OUT Join Date: Mar 2004 Location: LAS VEGAS Age: 39 Posts: 2,015 Trader Rating: (1) Rides Gallery: MELLO*SOS Feedback Score: 1 reviews	RB20DET.. One day it'll be done and installed, hopefully in Q1 2007. Still need a bazillion small things... Here is a close up of the Injector "block offs" I used for intake manifold leak down test. Made from home depot supplies: 1/2" rubber stoppers & some shelving screws 3" long with 1/2" heads, worked great. Set #1 to TDC, use leak down tester threaded into cyl #3 to pressurize manifolds to 2 bar/30psi... Spray down RTV'd areas on lower & upper mani's with soapy water. Not shown is TB blockoff plate made from a 5"x5" smooth wooden peice, drilled for tb bolts & with an improvised RTV gasket to seal with.

12-10-2006, 09:21 PM	#35
driftstyre Zilvia.net Advertiser Join Date: Jul 2003 Location: Boston Age: 42 Posts: 748 Trader Rating: (4) Feedback Score: 4 reviews	I wish it was even remotely this clean still.

12-11-2006, 01:44 AM	#39
amplifi3d Leaky Injector Join Date: Jun 2006 Location: honolulu Posts: 122 Trader Rating: (0) Feedback Score: 0 reviews	my friends v mount

12-11-2006, 05:23 PM	#40
redsuns3838 Zilvia Addict Join Date: Nov 2004 Location: dog town Posts: 969 Trader Rating: (0) Feedback Score: 0 reviews	theres mine.. Pretty messy. Im not big into dressup but i admit it is nice to have a nice looking engine bay. I really need to clean it up but does anyone have any tips on where to start? Im thinkin 1)golden eagle vac manifold 2)alumi intake pipe, 3)remove the ABS actuator and change over to non abs. have all the parts just no time. 4) relocate battery to trunk. have most of the hardware just need to pick up a circuit breaker any other tips besides those? Id like to relocate fusebox but I dont know if Im up for all that extending of wires =/ Last edited by redsuns3838; 12-11-2006 at 05:46 PM..

12-11-2006, 06:07 PM	#41
aNskY Nissanaholic! Join Date: Apr 2005 Location: NY Age: 37 Posts: 1,604 Trader Rating: (10) Feedback Score: 10 reviews	guess ill play, not very impressive,,,,.

12-15-2006, 10:53 PM	#42
-=RS13=- Leaky Injector Join Date: Jan 2004 Location: Canada Age: 34 Posts: 122 Trader Rating: (0) Feedback Score: 0 reviews	Well i will add. There is about 1 foot of snow up here so my cars not going anywhere. Its time for a good cleaning and then paint. No more abs and bracketry everwhere This was it before a little dirty __________________ Built by myself, Not by a shop and defintaly not bought. FTUW

12-16-2006, 12:06 PM	#43
Slidin240Wayz Post Whore! Join Date: Jan 2005 Location: Everywhere Age: 36 Posts: 5,427 Trader Rating: (9) Feedback Score: 9 reviews	My old kuruma. Carlos __________________ Support Zilvia by purchasing a sticker!

12-16-2006, 01:01 PM	#44
kuruptR Zilvia FREAK! Join Date: Jan 2003 Location: UpNorth Posts: 1,046 Trader Rating: (1) Feedback Score: 1 reviews	hard to see but only pic i got, s14 with tucked wiring harness __________________ @woooster on instagram

12-18-2006, 12:22 PM	#45
LookOut Nick Zilvia Addict Join Date: Aug 2006 Location: East Coast Age: 36 Posts: 816 Trader Rating: (0) Rides Gallery: LookOut Nick Feedback Score: 0 reviews	refill! __________________ *Team Pterodactyl*

12-18-2006, 02:24 PM	#46
vrooompssssht Leaky Injector Join Date: Dec 2006 Location: socal Posts: 138 Trader Rating: (0) Feedback Score: 0 reviews

12-18-2006, 03:56 PM	#47
holemilk00 Premium Member Join Date: Oct 2006 Location: Cape Coral, FL Posts: 2,485 Trader Rating: (33) Feedback Score: 33 reviews	I know you're all jealous of my stockness. But concidering the dirt pile this car was when I bought it its in heaven now with me, plus its getting stripped down like a broke hooker the night before rents due right after christmas, finally got most of my stuff for the swap.

12-18-2006, 05:31 PM	#48
LukeDogg316 Zilvia Member Join Date: May 2005 Location: San Diego Posts: 235 Trader Rating: (0) Feedback Score: 0 reviews	This thread is awesome here's my contribution before newer pic but still kinda old __________________

01-01-2007, 02:45 AM	#50
klattr1 Leaky Injector Join Date: Dec 2002 Location: SC and NC Age: 38 Posts: 112 Trader Rating: (0) Feedback Score: 0 reviews	my ka-t: __________________ KA24DER.com - Buy your supercharged KA24DER kits here!

01-01-2007, 10:25 AM	#51
rico05 Leaky Injector Join Date: Sep 2003 Location: College Station, Tx Posts: 83 Trader Rating: (0) Feedback Score: 0 reviews

01-01-2007, 01:04 PM	#52
Dousan_PG Post Whore! Join Date: May 2002 Location: Orange County, California Age: 42 Posts: 16,640 Trader Rating: (23) Rides Gallery: Dousan_PG Feedback Score: 23 reviews	painted my IC piping and did some polishing and im tired. that is all for now valve cover gets painted next week i think. sick of it being so bland and boring. my engine looks like shit compared with everyone else's. too busy busy. __________________ Aaron Pink GodziRa www.geocities.com/pink_godzira

01-14-2007, 08:29 PM	#53
s13silady Nissanaholic! Join Date: May 2002 Location: Bay Area, San Jose Posts: 1,804 Trader Rating: (0) Feedback Score: 0 reviews	got some more cleaning to do...its filthy.. but knowing me its probably gonna stay that way. __________________

01-14-2007, 10:57 PM	#54
ni5mo240 Zilvia Addict Join Date: Nov 2003 Location: Sacramento/Elk Grove, CA Age: 35 Posts: 908 Trader Rating: (11) Feedback Score: 11 reviews	This is mine, looks stealthy with the factory airbox cut out with HKS drop in filter and GT2530 turbo on the stock manifold! __________________ TUNAS. Jalostotitlan Jalisco Last edited by ni5mo240; 01-14-2007 at 11:51 PM..

01-14-2007, 11:23 PM	#55
brainfood Post Whore! Join Date: Jun 2004 Location: Eagle Rock, CA Age: 38 Posts: 2,957 Trader Rating: (18) Feedback Score: 18 reviews	__________________ Bryan Rogers http://www.seriousbadass.com

01-18-2007, 03:43 PM	#56
stuntman240 Leaky Injector Join Date: Feb 2003 Location: Cedar Rapids, Iowa Age: 36 Posts: 130 Trader Rating: (1) Feedback Score: 1 reviews	__________________ www.ClubFR.net

01-19-2007, 01:20 PM	#57
WhiteGLX Zilvia Addict Join Date: Jan 2003 Location: Baltimore, MD Age: 37 Posts: 872 Trader Rating: (7) Feedback Score: 7 reviews	Original Swap Rebuilt Motor V-mount Ducted V-Mount __________________ *NASA HPDE Instructor*

01-19-2007, 01:47 PM	#58
xxchurroxx Zilvia Member Join Date: Oct 2003 Location: NorCal Age: 37 Posts: 239 Trader Rating: (0) Rides Gallery: xxchurroxx Feedback Score: 0 reviews	__________________ v-mount ftmfw.

01-20-2007, 06:04 AM	#59
liv2drift045 Zilvia FREAK! Join Date: Feb 2005 Location: Chicagoland Age: 38 Posts: 1,483 Trader Rating: (7) Rides Gallery: liv2drift045 Feedback Score: 7 reviews	i hope to do a v-mount setup on the cefiro when i go sr... only time will tell... here's the current trash pit __________________ StreetSliders.Blogspot.com

01-25-2007, 12:54 PM	#60
LookOut Nick Zilvia Addict Join Date: Aug 2006 Location: East Coast Age: 36 Posts: 816 Trader Rating: (0) Rides Gallery: LookOut Nick Feedback Score: 0 reviews	__________________ *Team Pterodactyl*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode