Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 01-31-2020, 01:20 AM   #31
Presto
Leaky Injector
 
Presto's Avatar
 
Join Date: Mar 2019
Location: USA
Posts: 96
Trader Rating: (0)
Presto is an unknown quantity at this point
Feedback Score: 0 reviews
Got a 240sx it’s my first car I’m working on I’m replacing the gas tank which was rusted out again after I tried cleaning the rust the first time, and I just ordered new pump,sending unit, and tank, Previous owner deleted charcoal canister, I’m trying to avoid future rusting of my new parts

These are my options:

1.If I have fuel tank evap nipple>check valve>hard line that runs up To engine bay and cut where I think the charcoal canister might have been (previous owner deleted) + s14 gas cap, am I good on the explosion/implosion/rusting?

2.What if I removed the check valve, capped the line from the evap nipple and buy an s14 gas cap? Am I risking rust and issues still?

3.Can I run a hose from the evap nipple to a filter like in this thread, and buy an s14 gas cap? Or would this let moisture and things into the tank?

I’m just confused but please help me if no one replies I’ll probably just go with option 1 or 2 and hope I don’t blow up or waste $1000

Last edited by Presto; 01-31-2020 at 02:10 AM..
Presto is offline   Reply With Quote
Sponsored Links
Old 02-07-2020, 10:19 PM   #32
Dsmguy1993
Leaky Injector
 
Join Date: Aug 2019
Location: Illinois
Age: 27
Posts: 135
Trader Rating: (0)
Dsmguy1993 is an unknown quantity at this point
Feedback Score: 0 reviews
I had to do this on my old s13 because I live in the midwest so the old fuel lines got rusted out, sourced the hardlines off another s13 and make shifted my own underbody mounts. What I do with that line is let it vent to atmosphere, but I did not think about using a filter to keep debris out very good idea. Good write up always knew venting was critical, but never knew how much of a safety problem it is too.
Dsmguy1993 is offline   Reply With Quote
Old 02-13-2020, 04:35 AM   #33
ph1tnessjunk1e
 
Join Date: Jul 2016
Location: Columbus, OH
Age: 34
Posts: 33
Trader Rating: (0)
ph1tnessjunk1e is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by KiLLeR2001 View Post
As I expected I knew some information would be flawed.

The fuel check valve works as an equalizer for the fuel tank. On hot summer days, there will actually be positive pressure that will accumulate inside the tank. If you only install a one-way valve (vacuum) or keep the fuel check valve but block off the fuel vent, you will have problems. And by problems I mean premature fuel pump failure.

The fuel check valve will release a little bit of fuel vapor when the pressure exceeds X amount of psi. The fuel cap is vacuum only for S13's. If you vent to atmosphere with no fuel check valve installed, then you basically have an open system and moisture will creep into the tank and then you can say hello to a rusty S13 fuel tank for me.

If you want to block off the fuel vent, you can, but you must install an OEM S14 fuel cap because that acts as a two-way valve just like the fuel check valve.

Personally, I have an S14 fuel cap and a functioning fuel check valve so that way if one fails, the other is there as a fail-safe. I left the factory hard lines alone so it vents out right where the charcoal canister was. Been running it like this for 6 years and no IMPLOSION/EXPLOSION has occurred (like you are implying).

Ok, I want to make sure I do this right so I want to confirm my understanding.

Venting to the atmosphere, even with a filter like the original post says, is not good. In order to properly do this, we must use a S14 fuel cap and fuel check valve that releases pressure at a certain PSI - both are needed if redundancy is desired.

Is that right? If yes, what fuel check valve did you use? Do you know the PSI at which the factory valve releases pressure?
ph1tnessjunk1e is offline   Reply With Quote
Old 05-22-2020, 11:46 AM   #34
Bleakley
Zilvia Addict
 
Join Date: Apr 2011
Location: Near Pittsburgh, PA
Posts: 634
Trader Rating: (1)
Bleakley is an unknown quantity at this point
Feedback Score: 1 reviews
Speaking for S13’s:
I set up SOHC’s and DOHC’s the same way when you’re stock or N/A and retaining EVAP or just trying to capture fuel vapors (some places are UBER F***ing anal about looking for this).

-I run the 1/4” line from manifold to canister. (Vacuum source between throttle body and engine)
-I run 5/32” line (w/ the factory restrictor installed in the line!) from any source between throttle body and MAFS. Preferably the throttle body nipple. This ensures purge during partial throttle / cruise situations as intended.
—> Retain OEM check valve.

I have ran multiple cars like this for 8-9 years.

Once you go turbo it’s up to you what you want to do as shuttle changes must take place.
What I do for simplicity is delete canister, EVAP, and all the bullshit. I utilize the existing hardline under the car, hook it up to tank vent, then at the other end I put a hose on it and either a) run it to turbo intake or b) put a filter on the end of hose and lay it REALLY close to air filter for turbo intake. Both methods work.
The potential for fuel vapors to gather under hood are slim, but DO exist. I’ve ran it this way for a year or two.
The other simpler option is running the filter to rear bumper or some location out from under car but preferably higher than fuel tank.
Bleakley is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:11 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™