Check out my new BIG BRAKES!! anyone else do this yet??? - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Krinkov · 11-01-2005, 05:25 PM

stock rear.

Sti rear Brembo with EVO rear rotor

and it BOLTS RIGHT UP!!

it needs a 3mm spacer here for the correct offset, you need to trim/remove the dust cover thats all, the brembo brake line even screws right in!

For comparison.

I have the fronts going on too, but I need to machine a couple brackets, I had an extra set of the gold STI brembos, but Im close to certain the red EVO brembo calipers use the same bolt spacing. EVO take-off Brembos are pretty cheap, either from wreck part-outs or people upgrading, theres not a big market to sell them since all other EVO guys already have brembos so Ive seen whole sets front and rear sell for around $600! Im making a few sets of front brackets, let me know if anyone wants any

rancid240 · 11-01-2005, 05:28 PM

What you gonna do for ebrake?

Krinkov · 11-01-2005, 05:44 PM

Quote:

Originally Posted by rancid240

What you gonna do for ebrake?

gonna make a bracket to run a secondary wilwood cable E-brake caliper like the Ferraris do.

until then guess I'll be parking in gear like alot of the guys with Z32 rear swaps do that dont swap over the drum brake

THX1138 · 11-01-2005, 05:46 PM

More importantly, how do you plan to bleed them? Unless you're gonna put the car on a rotisserie to bleed the brakes, make sure you switch those things side-to-side before you put it on the road.

Good call on the Wilwood spot caliper. I'm almost definitely gonna go that route whenever I get around to upgrading the rear brakes.

WILDACEX187 · 11-01-2005, 05:48 PM

umm wat about the front?

A Spec Products · 11-01-2005, 06:03 PM

very cool

i was gonna do this with a set of evo 8 brakes we have here, but never had time

keep us updated, thats nice, STI x EVO combined

is it installed upside down, i thought u need to install the bleeder facing up?

OptionZero · 11-01-2005, 06:06 PM

Cool, are STI/EVO brakes identical?

Because i'd have thought that 5x100 bolt pattern would have been a deterrant, but hey cool.

Still alot of work since there's no provision for e-brake, but if you want the bling, it's impressive.

Krinkov · 11-01-2005, 06:33 PM

Quote:

Originally Posted by THX1138

More importantly, how do you plan to bleed them? Unless you're gonna put the car on a rotisserie to bleed the brakes, make sure you switch those things side-to-side before you put it on the road.

Good call on the Wilwood spot caliper. I'm almost definitely gonna go that route whenever I get around to upgrading the rear brakes.

haha, these are just a mock up, only had the one caliper handy today but yes I have the right ones for the right sides, no point in running big rear brakes and stock front brakes untill I get the fronts installed

Krinkov · 11-01-2005, 06:34 PM

Quote:

Originally Posted by WILDACEX187

umm wat about the front?

umm did you even read the post?

Krinkov · 11-01-2005, 06:37 PM

Quote:

Originally Posted by OptionZero

Cool, are STI/EVO brakes identical?

Because i'd have thought that 5x100 bolt pattern would have been a deterrant, but hey cool.

Still alot of work since there's no provision for e-brake, but if you want the bling, it's impressive.

you think having big brakes is is just for "bling"

and yes, you cant run the 04STI rotors since they are 5X100, the 05+ STI run the 5X114 but I dont know what the offset of those are, might get a set of those too to play around with, I'll keep this updated

WILDACEX187 · 11-01-2005, 07:30 PM

Quote:

Originally Posted by Krinkov

umm did you even read the post?

wat i tried to say is that why wont u get a weird brake balance if u have such big brakes in the rear and stock front? wat kind of master cylinder will u use?

SirWarrior · 11-01-2005, 07:43 PM

Nice write up.
But I already went the Z32 route and my S14 came with Z32s already on them.
But its good to see someone out there is actually thinking outside the box

aznpoopy · 11-01-2005, 07:53 PM

Quote:

Originally Posted by WILDACEX187

wat i tried to say is that why wont u get a weird brake balance if u have such big brakes in the rear and stock front? wat kind of master cylinder will u use?

he said it in the first post

Quote:

I have the fronts going on too, but I need to machine a couple brackets, I had an extra set of the gold STI brembos, but Im close to certain the red EVO brembo calipers use the same bolt spacing.

interesting swap. its nice to know we have yet another option.

kingsol · 11-01-2005, 07:55 PM

props for trying something new. can't wait till everything is figured out.

black s13 · 11-01-2005, 07:56 PM

Quote:

Originally Posted by WILDACEX187

wat i tried to say is that why wont u get a weird brake balance if u have such big brakes in the rear and stock front? wat kind of master cylinder will u use?

so you really didnt read the post?

he went over it at least twice.

props, looks good. i was working on my friends STi this evening and wondered how difficult it would be to swap the brakes.

Krinkov · 11-01-2005, 08:13 PM

Quote:

Originally Posted by SirWarrior

Nice write up.
But I already went the Z32 route and my S14 came with Z32s already on them.
But its good to see someone out there is actually thinking outside the box

thanks, this inst quite a "write up" just yet, just excited and thought I would post this first, I'll probably do a full write up when I get the fronts sorted and figure out what Im going to do for an E-brake. I was looking at front/rear Z32s to begin with but if all goes well I might be able to pull this off for close to what you could usually find Z32 front/rears for, and since both my other two cars run these same Brembos, Im a bit partial to them

theicecreamdan · 11-01-2005, 08:37 PM

*subscribes*

wow, good to know.

NZO · 11-02-2005, 12:16 AM

Uh oh Jeremy is into nissans now. Dangerous...

DP_Michelle G · 11-02-2005, 12:21 AM

very nice keep us updated

Supreme · 11-02-2005, 01:11 AM

Other than the bolt pattern of the 04 sti, evo/sti brembos are the same. Only thing is EVO brembos are easier to find, the sti brembos sell FAST to ej20 owners. They both use the same exact pads with 4 pot front/2 pot rear.

Ritz S14 · 11-02-2005, 01:11 AM

Looks like you'd need a rotor eccentric ring. What size pison are those in comparison with z32 rears? and weight?

Supreme · 11-02-2005, 01:16 AM

Oh and if your able, replace those rotors with Powerslot/Rotora/StopTech/Endless/P.MU or whichever floats your boat, their not the best durability wise and youll have to do it later anyway.

Krinkov · 11-02-2005, 02:15 AM

Quote:

Originally Posted by Supreme

Other than the bolt pattern of the 04 sti, evo/sti brembos are the same. Only thing is EVO brembos are easier to find, the sti brembos sell FAST to ej20 owners. They both use the same exact pads with 4 pot front/2 pot rear.

well they are very close but there are slight differences,
EVO rotors
Front = 320mm
Rear = 300mm

STI
Front = 326mm
Rear = 316mm

another interesting note is that the EVO front rotors are 32mm wide whereas the STI fronts are 30mm wide. They use the same Brembo caliper but the EVO actually uses 1mm skinnier brake pads! so you can use EVO pads on STI and just be short a bit of pad life(Ive dont this on my STI) but you cant use STI pads on an EVO unless you turn the rotors down 2mm. Some companies, Like EBC, only make one part number for EVO and STI pads and just cheat STI guys out of 1mm on each pad, lol.

One other difference in the fronts, besides the diameter, is the hat height(offset) the STI(53mm) is almost identical to the 300ZX(54mm) whereas the EVO is 43.5mm. Since Im designing custom brackets anyways, I can make them to whatever offseet they need to be to fit, though all things being equal, the EVO rotors will move the Brembo caliper about 10mm closer to the wheel than the STI or Z32 rotors, so that could be a clearance problem depending on what wheel your running, the best combo might be EVO rear rotors and 05+ STI(%X114) front calipers to keep the offset as close to stock as possible, and they're 6mm bigger to boot!

Angel · 11-02-2005, 07:36 AM

Just subscribed.
Kepp us updated for sure. Now to make off with the brakes from one of my coworker's evos here at the shop

**mrmephistopheles** · 11-02-2005, 07:45 AM

Quote:

Originally Posted by Krinkov

stock rear.

Sweet Jeebus that's a skinny exhaust!

Good work with the install.

BigVinnie · 11-02-2005, 07:56 AM

Quote:

Originally Posted by Krinkov

gonna make a bracket to run a secondary wilwood cable E-brake caliper like the Ferraris do.

until then guess I'll be parking in gear like alot of the guys with Z32 rear swaps do that dont swap over the drum brake

It seems like this company is way ahead of you...
http://arizonazcar.com/240sxbrakes.html

HyperTek · 11-02-2005, 08:33 AM

id hope the hat area is sitting againts the hubs or thats some nasty flemingo action..

I say screw the wilwood brakes, tahts extra crap to put in the conversion, *not to mention added weight and lines* just put a hydrolic ebrake level that connects to the rear brake lines.

So what brake master cylinder are you going to swap? Id asume u where going to change that too... I wonder how bad the brake bias will be...

projectRDM · 11-02-2005, 08:35 AM

Quote:

Originally Posted by BigVinnie

It seems like this company is way ahead of you...
http://arizonazcar.com/240sxbrakes.html

That has nothing to do with what he has planned. His idea was to use Wilwoods strictly as a secondary caliper for the ebrake, not the replace the OE caliper.

BigVinnie · 11-02-2005, 08:53 AM

Quote:

Originally Posted by R240NA

That has nothing to do with what he has planned. His idea was to use Wilwoods strictly as a secondary caliper for the ebrake, not the replace the OE caliper.

My bad didn't notice he was going to use it for strictly E-Braking.......

Krinkov · 11-02-2005, 11:15 AM

Quote:

Originally Posted by NZO

Uh oh Jeremy is into nissans now. Dangerous...

LOL, thought I would find you over here!

I'll still keep a flying Subaru or two though, lol

11-01-2005, 05:25 PM	#1
Krinkov Leaky Injector Join Date: Sep 2005 Location: SF Bay Area Age: 47 Posts: 89 Trader Rating: (0) Feedback Score: 0 reviews	Check out my new BIG BRAKES!! anyone else do this yet??? stock rear. Sti rear Brembo with EVO rear rotor and it BOLTS RIGHT UP!! it needs a 3mm spacer here for the correct offset, you need to trim/remove the dust cover thats all, the brembo brake line even screws right in! For comparison. I have the fronts going on too, but I need to machine a couple brackets, I had an extra set of the gold STI brembos, but Im close to certain the red EVO brembo calipers use the same bolt spacing. EVO take-off Brembos are pretty cheap, either from wreck part-outs or people upgrading, theres not a big market to sell them since all other EVO guys already have brembos so Ive seen whole sets front and rear sell for around $600! Im making a few sets of front brackets, let me know if anyone wants any

11-01-2005, 05:48 PM	#5
WILDACEX187 Post Whore! Join Date: Jan 2003 Location: QUEENZ, NYC Age: 38 Posts: 3,103 Trader Rating: (4) Feedback Score: 4 reviews	umm wat about the front? __________________ SR POWA COUPE LUVVV!!!

11-01-2005, 06:03 PM	#6
A Spec Products Post Whore! Join Date: Mar 2005 Location: Socal! Off 60/605 Posts: 7,256 Trader Rating: (27) Feedback Score: 27 reviews	very cool i was gonna do this with a set of evo 8 brakes we have here, but never had time keep us updated, thats nice, STI x EVO combined is it installed upside down, i thought u need to install the bleeder facing up? __________________ A SPEC PRODUCTS CORP AME Wheels, Advan, ARC, Gram Lights, Nardi, Personal, Recaro, Works Bell, Work Wheels, Volk Racing, 5Zigen, & more! 626.618.1100 x 103 / aim: aspectuan Advertiser's Specials! Read / Give Feedback! Please Rate Us!

11-01-2005, 07:43 PM	#12
SirWarrior Zilvia Addict Join Date: May 2004 Location: Chicagoland Posts: 762 Trader Rating: (0) Feedback Score: 0 reviews	Nice write up. But I already went the Z32 route and my S14 came with Z32s already on them. But its good to see someone out there is actually thinking outside the box __________________ 92 FastBack - Project 98 SE - Daily Driver

11-01-2005, 07:55 PM	#14
kingsol Zilvia FREAK! Join Date: Jun 2003 Location: Berkeley/San Francisco Posts: 1,435 Trader Rating: (0) Feedback Score: 0 reviews	props for trying something new. can't wait till everything is figured out. __________________ There is a time in every man's education when he arrives at the conviction that envy is ignorance; that imitation is suicide; that he must take himself for better for worse as his portion; that though the wide universe is full of good, no kernel of nourishing corn can come to him but through his toil bestowed on that plot of ground which is given to him to till. -Emerson

11-01-2005, 05:28 PM	#2
rancid240 Post Whore! Join Date: Jan 2002 Location: Irvine CA Posts: 2,770 Trader Rating: (72) Feedback Score: 72 reviews	What you gonna do for ebrake?

11-01-2005, 05:46 PM	#4
THX1138 Zilvia Member Join Date: Sep 2002 Location: Clemson, SC Posts: 264 Trader Rating: (0) Feedback Score: 0 reviews	More importantly, how do you plan to bleed them? Unless you're gonna put the car on a rotisserie to bleed the brakes, make sure you switch those things side-to-side before you put it on the road. Good call on the Wilwood spot caliper. I'm almost definitely gonna go that route whenever I get around to upgrading the rear brakes.

11-01-2005, 06:06 PM	#7
OptionZero Post Whore! Join Date: Jul 2003 Location: Norcal Age: 37 Posts: 6,262 Trader Rating: (2) Rides Gallery: OptionZero Feedback Score: 2 reviews	Cool, are STI/EVO brakes identical? Because i'd have thought that 5x100 bolt pattern would have been a deterrant, but hey cool. Still alot of work since there's no provision for e-brake, but if you want the bling, it's impressive.

11-02-2005, 12:16 AM	#18
NZO Zilvia FREAK! Join Date: Mar 2002 Location: Reno, NV Age: 38 Posts: 1,424 Trader Rating: (0) Rides Gallery: NZO Feedback Score: 0 reviews	Uh oh Jeremy is into nissans now. Dangerous... __________________ sentinelguild.com/nzo/PFCDB/

11-02-2005, 12:21 AM	#19
DP_Michelle G Zilvia Addict Join Date: Aug 2005 Location: Anaheim/OC Age: 38 Posts: 666 Trader Rating: (0) Feedback Score: 0 reviews	very nice keep us updated Last edited by DP_Michelle G; 11-02-2005 at 12:22 AM.. Reason: i can't spell for shit tonite sleepie

11-02-2005, 01:11 AM	#20
Supreme Leaky Injector Join Date: Sep 2005 Location: Queens SQC Posts: 55 Trader Rating: (0) Feedback Score: 0 reviews	Other than the bolt pattern of the 04 sti, evo/sti brembos are the same. Only thing is EVO brembos are easier to find, the sti brembos sell FAST to ej20 owners. They both use the same exact pads with 4 pot front/2 pot rear. __________________ Signature Exceeds Forum Limits

11-02-2005, 01:11 AM	#21
Ritz S14 Post Whore! Join Date: Jul 2004 Location: C A L I F O R N I A Age: 39 Posts: 3,586 Trader Rating: (0) Feedback Score: 0 reviews	Looks like you'd need a rotor eccentric ring. What size pison are those in comparison with z32 rears? and weight?

11-02-2005, 01:16 AM	#22
Supreme Leaky Injector Join Date: Sep 2005 Location: Queens SQC Posts: 55 Trader Rating: (0) Feedback Score: 0 reviews	Oh and if your able, replace those rotors with Powerslot/Rotora/StopTech/Endless/P.MU or whichever floats your boat, their not the best durability wise and youll have to do it later anyway. __________________ Signature Exceeds Forum Limits

11-02-2005, 07:36 AM	#24
Angel Zilvia Junkie Join Date: Jan 2005 Location: Orlando Posts: 319 Trader Rating: (0) Feedback Score: 0 reviews	Just subscribed. Kepp us updated for sure. Now to make off with the brakes from one of my coworker's evos here at the shop __________________ S13 redtop 2871R.64 377 rwhp 322 rwtq 11.5 @ 117

11-02-2005, 08:33 AM	#27
HyperTek Post Whore! Join Date: Mar 2003 Location: Cali Posts: 13,222 Trader Rating: (3) Feedback Score: 3 reviews	id hope the hat area is sitting againts the hubs or thats some nasty flemingo action.. I say screw the wilwood brakes, tahts extra crap to put in the conversion, not to mention added weight and lines just put a hydrolic ebrake level that connects to the rear brake lines. So what brake master cylinder are you going to swap? Id asume u where going to change that too... I wonder how bad the brake bias will be... __________________ Keep it Classy

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode