Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk

Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 11-24-2017, 04:30 PM   #1
unicoder
Zilvia Member
 
unicoder's Avatar
 
Join Date: Apr 2017
Location: Alabama
Posts: 160
Trader Rating: (2)
unicoder is an unknown quantity at this point
Feedback Score: 2 reviews
s14 Z32 MAF question

Just installed turbo kit onto KA24DE S14

Car runs, but falls on its face when you hit the gas for a second then revs. I can drive it but if you give any force to the gas it will bog before taking off. Also when idling every minute or so it will drop RPM's about to die and then catch back up.

While going through all of the troubleshooting steps I found while searching this forum, I get to the Z32 MAF. Now according to that popular JWT diagram floating around I should have .5v on the left pin of the harness(B), and 12V on the right of the harness(E), mine were backwards

link to said diagram

Questions:
- Why was it semi-running when the 12v and .5v were backwards?
- Why is it in limp mode now that I have corrected it? Wont rev past 2500.
- Was the MAF bad the whole time? I am going to just buy a new one tomorrow and test it, but wanted to make sure I had my ducks in a row first.

additional info
- injectors tested ok
- TPS tested ok
- no vacuum leaks
- brand new 255lph fuel pump
- new wires, plugs
- new battery
__________________

5.3 V8 Swap w/ Nitrous
unicoder is offline   Reply With Quote
Sponsored Links
Old 11-24-2017, 06:08 PM   #2
derass
Zilvia FREAK!
 
Join Date: Jun 2010
Location: Toronto, ON
Age: 33
Posts: 1,182
Trader Rating: (0)
derass is making a name for him/her selfderass is making a name for him/her self
Feedback Score: 0 reviews
What ECU?

msglngth
derass is offline   Reply With Quote
Old 11-24-2017, 06:28 PM   #3
unicoder
Zilvia Member
 
unicoder's Avatar
 
Join Date: Apr 2017
Location: Alabama
Posts: 160
Trader Rating: (2)
unicoder is an unknown quantity at this point
Feedback Score: 2 reviews
RS-Enthalpy

Just realized that diagram pdf is from the BACK side of the harness plug where the wires go in. Turns out i had it wired correctly from the start.

Swapped them back and started the car again, luckily once it warmed up it wasn't idle surging or bogging. Man I hope it was all a fluke..

I will ground the extra brown wire from the ISR Pigtail to chassy instead of the harness in the morning. Hopefully all is well then.

**also, i havent filled the car with the 91 octane it's tuned for, still have about a 1/4 tank of 87 in it, would that do the bogging?idle surging?
__________________

5.3 V8 Swap w/ Nitrous
unicoder is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 04:12 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™