Parts Shop MAX ~ ORIGINAL TIE RODS ~ In Stock! FREE shipping, order direct in thread! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

DC Dan MAX USA · 12-07-2010, 03:46 PM

Introducing: Parts Shop MAX original TIE RODS!

You can buy stuff and get live shipping quotes right here in this thread!
Simply click the blue add to cart link to check it out.
VIEW CART

Long and strong! This inner tie rod was created with large diameter, extra long length, and built in 1pc. 7mm angle spacers! The extra length is a must for our super angle kit modded knuckles or for customers widening the track width in front with aftermarket lower control arms. You can still use them with all OEM parts but you have to cut about 3/4" of the threads off. This makes the multi piece design of the Ikeya Formula rods we used to sell is just not necessary. Since it is a one piece design, we are able to give a smoking price on these.

We will also sell matching OEM style strengthened ends just like we have always recommended using (SAK modded knuckles dont need bumpsteer spacers found on all the aftermarket outers)

Max original tie rods are much stronger than OEM because of the increased diameter however in the case of a collision, we have you covered because our special steel alloy is factory tested to bend 180 degrees without breaking!

Although the steering rack angle spacers are built in, and give enough angle without modded knuckles to over center, the thread on the rack end is the same length as other tie rods made for slip on spacers. In other words, you get the same steering angle as other inner tie rods with 7mm slip on spacers like Ikeya, but you have more thread engagement inside the rack.

Optionally if you have a mod that moves the rack forward to prevent over centering there is room to stack on additional angle spacers.

In the MAX original design we have moved the hex adjuster away from the center of the rod to a larger diameter area closer to the ball joint. We did that because we found that in a crash situation, the energy focuses on the sharp edges of the hex adjuster causing a crack or a break, but on the MAX tie rod it can absorb and distribute the energy more evenly to prevent failure.

The diameter is only compatible with S14 outer tie rods (any brand or OEM is OK)
but S13 rod ends are too thin and should be upgraded. The rack threads are the same weather its S13 or S14.

Price is $75 per pair of MAX inner tie rods with free shipping world wide. Limited time introductary offer, no coupon code needed. New stock has just arrived! Limited lifetime warranty.
CLICK HERE TO ADD TO CART & ORDER ONLINE

Here are some pictures of the Inner tie rods installed on my car and attached to our roll center modded Super Angle Knuckles.

VIEW CART

axlegrease · 12-07-2010, 04:42 PM

Damn that angle is sick!!! Lol in the last two pics it looks like that tie rod BARELY clears the wheel.

chiboy002 · 12-07-2010, 05:13 PM

me gusta pero no tengo dinero horita... ffffffuuuuuuuuuu!!
lol translate that bitch!

Are you guys going to run something like cheap or free thread slimming? I have a hack saw at my house and i would not feel comfortable using that to hack threads lol.

LOOKS GOOD AND IM JEALOUS

*TheRealSy90* · 12-07-2010, 05:54 PM

Too bad I'd have to cut the threads if I bought these, might as well wait and get the angle kit

These are SUPER beefy though.

roboticnissan · 12-07-2010, 07:07 PM

Buy now cry later haha^^^^

DC Dan MAX USA · 12-07-2010, 07:18 PM

Quote:

Originally Posted by axlegrease

Damn that angle is sick!!! Lol in the last two pics it looks like that tie rod BARELY clears the wheel.

wheel barely clears the frame too so its just perfect = )

Quote:

Originally Posted by chiboy002

me gusta pero no tengo dinero horita... ffffffuuuuuuuuuu!!
lol translate that bitch!

Are you guys going to run something like cheap or free thread slimming? I have a hack saw at my house and i would not feel comfortable using that to hack threads lol.

LOOKS GOOD AND IM JEALOUS

lol, thanks

This is just about the cheapest mod out there so you are in luck, this is 50% less than the Ikea Formula rods we used to sell, and about the same price as Moog so with the free shipping its quite an amazing deal IMO

you can select in the shopping cart two options:

~ Leave these long so I can run Super Angle Knuckles or wider lower control arms

or

~ Please cut them to OEM length because I am never modding my knuckles or LCA's

there is no additional charge if you wuss out.

onehundredoctane · 12-07-2010, 07:24 PM

stock vs PBM

DC Dan MAX USA · 12-07-2010, 07:34 PM

thanks for posting the pic !

onehundredoctane · 12-07-2010, 07:47 PM

No prob! Now hurry up and release the PBM lower control arm/ tension rod kit!

I WANT!!

DC Dan MAX USA · 12-07-2010, 08:04 PM

We're trying to release it in February, wish us luck on that goal!

Souljahzs13 · 12-07-2010, 09:10 PM

Quote:

Originally Posted by DC Dan MAX USA

We're trying to release it in February, wish us luck on that goal!

AWW!! I was hoping this will be out in January, I have been saving my money for the complete front and rear kit

gijoe69 · 12-07-2010, 09:32 PM

I have these Inner Tie Rods for S14 on a stock control arm. Make sure you cut & grind about 1/2" off the threads or it will never be centered and unable to get alignment.

DC Dan MAX USA · 12-07-2010, 09:44 PM

Souljah, It's worth the wait because there is a bunch of stuff we have improved upon since the prototype.

chiprez · 12-08-2010, 10:51 AM

With any luck ill be picking tgeese up when the paycheck comes in

Souljahzs13 · 12-09-2010, 09:32 PM

Quote:

Originally Posted by DC Dan MAX USA

Souljah, It's worth the wait because there is a bunch of stuff we have improved upon since the prototype.

I know Dan lol I have new coilovers want to slam my car already but until I have the adjustable control arms to correct my alignment, bumpsteer, and roll center haha

zurud · 12-10-2010, 01:55 AM

any warranty?

lewyS14a · 12-10-2010, 07:53 AM

Just ordered some , wish there was more stuff i could buy with free shipping haha

DC Dan MAX USA · 12-10-2010, 01:20 PM

There is a limited lifetime warranty on this part.

dino6192 · 12-15-2010, 06:14 AM

I love the new design and product!
Looks like I have to add these to the PSM collection on the S13 when I come back in Feb!
lets go to the track and test them out together!

-Steve

satek · 12-20-2010, 03:32 PM

Just ordered mine!!

Bullet01 · 12-25-2010, 10:52 AM

Any pics or info on your OEM modified tie rod ends?

DC Dan MAX USA · 12-30-2010, 04:17 PM

POWERED BY MAX: Forums
see the link for pictures, its OEM style since our super angle kit already spaces down the tie rod end. Also they last longer than ends with the bearing exposed.
those are not released yet.

Datenshi · 01-01-2011, 04:39 PM

Wish these were out when I replaced my tie rods, would have bought them for sure. Good price, amazing guys and amazing products. +1 for PBM can't wait til spring to order full multi-link from you guys to go with these beautiful coils I got from you that I sadly have sitting on my desk to stare at and help winter go by faster. :P

PITCH · 01-01-2011, 05:01 PM

Skid plate... Where can I buy?

nathanong87 · 01-03-2011, 08:18 AM

Quote:

Originally Posted by PITCH

Skid plate... Where can I buy?

u try their website?.....

DC Dan MAX USA · 01-10-2011, 03:39 PM

Quote:

Originally Posted by Datenshi

Wish these were out when I replaced my tie rods, would have bought them for sure. Good price, amazing guys and amazing products. +1 for PBM can't wait til spring to order full multi-link from you guys to go with these beautiful coils I got from you that I sadly have sitting on my desk to stare at and help winter go by faster. :P

thanks for the feedback!

MIKE-240sx · 01-10-2011, 07:35 PM

orderd these a couple days ago, waiting for em to come in. +1 for affordable tie rods with free shipping! everyone should take advantage of this offer

DC Dan MAX USA · 01-26-2011, 03:41 PM

there is too many [free] requests for shortening the tie rods, so we are now charging $15 for the labor to cut the length.

DC Dan MAX USA · 02-01-2011, 04:01 PM

Sold out - We'll have more in march.

eklipse38 · 03-20-2011, 09:43 PM

I have a set of the PBM tie rods paired with the Tein outers. I also have one of these steering spacers http://zilvia.net/f/suspension/36731...new-price.html. I had to cut about an inch off the PBM tie rods and after instaling and centering the rack spacer I have ran out of threads can i have the inners machined with more threads or should i just remove the rack spacer? I was able to set the toe before I instaled the spacer but now both sides are toed-in a ton.

12-07-2010, 03:46 PM	#1
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	Parts Shop MAX ~ ORIGINAL TIE RODS ~ In Stock! FREE shipping, order direct in thread! Introducing: Parts Shop MAX original TIE RODS! You can buy stuff and get live shipping quotes right here in this thread! Simply click the blue add to cart link to check it out. VIEW CART Long and strong! This inner tie rod was created with large diameter, extra long length, and built in 1pc. 7mm angle spacers! The extra length is a must for our super angle kit modded knuckles or for customers widening the track width in front with aftermarket lower control arms. You can still use them with all OEM parts but you have to cut about 3/4" of the threads off. This makes the multi piece design of the Ikeya Formula rods we used to sell is just not necessary. Since it is a one piece design, we are able to give a smoking price on these. We will also sell matching OEM style strengthened ends just like we have always recommended using (SAK modded knuckles dont need bumpsteer spacers found on all the aftermarket outers) Max original tie rods are much stronger than OEM because of the increased diameter however in the case of a collision, we have you covered because our special steel alloy is factory tested to bend 180 degrees without breaking! Although the steering rack angle spacers are built in, and give enough angle without modded knuckles to over center, the thread on the rack end is the same length as other tie rods made for slip on spacers. In other words, you get the same steering angle as other inner tie rods with 7mm slip on spacers like Ikeya, but you have more thread engagement inside the rack. Optionally if you have a mod that moves the rack forward to prevent over centering there is room to stack on additional angle spacers. In the MAX original design we have moved the hex adjuster away from the center of the rod to a larger diameter area closer to the ball joint. We did that because we found that in a crash situation, the energy focuses on the sharp edges of the hex adjuster causing a crack or a break, but on the MAX tie rod it can absorb and distribute the energy more evenly to prevent failure. The diameter is only compatible with S14 outer tie rods (any brand or OEM is OK) but S13 rod ends are too thin and should be upgraded. The rack threads are the same weather its S13 or S14. Price is $75 per pair of MAX inner tie rods with free shipping world wide. Limited time introductary offer, no coupon code needed. New stock has just arrived! Limited lifetime warranty. CLICK HERE TO ADD TO CART & ORDER ONLINE Here are some pictures of the Inner tie rods installed on my car and attached to our roll center modded Super Angle Knuckles. VIEW CART __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business! Last edited by DC Dan MAX USA; 12-10-2010 at 01:19 PM..

12-07-2010, 05:13 PM	#3
chiboy002 Post Whore! Join Date: Mar 2010 Location: ◙ Posts: 4,416 Trader Rating: (21) Feedback Score: 21 reviews	me gusta pero no tengo dinero horita... ffffffuuuuuuuuuu!! lol translate that bitch! Are you guys going to run something like cheap or free thread slimming? I have a hack saw at my house and i would not feel comfortable using that to hack threads lol. LOOKS GOOD AND IM JEALOUS __________________ street dancer.

12-07-2010, 07:07 PM	#5
roboticnissan Nissanaholic! Join Date: Mar 2007 Location: SOCAL/NORCAL Age: 32 Posts: 1,867 Trader Rating: (12) Feedback Score: 12 reviews	Buy now cry later haha^^^^ __________________

12-07-2010, 07:34 PM	#8
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	thanks for posting the pic ! __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

12-07-2010, 08:04 PM	#10
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	We're trying to release it in February, wish us luck on that goal! __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

12-07-2010, 04:42 PM	#2
axlegrease Join Date: Jul 2010 Location: Atlanta, GA Age: 34 Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	Damn that angle is sick!!! Lol in the last two pics it looks like that tie rod BARELY clears the wheel.

12-07-2010, 07:24 PM	#7
onehundredoctane Post Whore! Join Date: Oct 2006 Location: Greensborough, NC Posts: 2,783 Trader Rating: (3) Feedback Score: 3 reviews	stock vs PBM

12-07-2010, 07:47 PM	#9
onehundredoctane Post Whore! Join Date: Oct 2006 Location: Greensborough, NC Posts: 2,783 Trader Rating: (3) Feedback Score: 3 reviews	No prob! Now hurry up and release the PBM lower control arm/ tension rod kit! I WANT!!

12-07-2010, 09:32 PM	#12
gijoe69 Zilvia Junkie Join Date: May 2003 Location: San Francisco, CA Age: 36 Posts: 366 Trader Rating: (1) Feedback Score: 1 reviews	I have these Inner Tie Rods for S14 on a stock control arm. Make sure you cut & grind about 1/2" off the threads or it will never be centered and unable to get alignment.

12-07-2010, 09:44 PM	#13
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	Souljah, It's worth the wait because there is a bunch of stuff we have improved upon since the prototype. __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

12-08-2010, 10:51 AM	#14
chiprez Join Date: Sep 2008 Location: Vancouver,Wa Age: 30 Posts: 28 Trader Rating: (0) Feedback Score: 0 reviews	With any luck ill be picking tgeese up when the paycheck comes in

12-10-2010, 01:55 AM	#16
zurud Zilvia Junkie Join Date: Aug 2009 Location: evansville, in Posts: 391 Trader Rating: (4) Feedback Score: 4 reviews	any warranty?

12-10-2010, 07:53 AM	#17
lewyS14a Join Date: Dec 2009 Location: UK Posts: 44 Trader Rating: (0) Feedback Score: 0 reviews	Just ordered some , wish there was more stuff i could buy with free shipping haha

12-10-2010, 01:20 PM	#18
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	There is a limited lifetime warranty on this part. __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

12-15-2010, 06:14 AM	#19
dino6192 Zilvia Addict Join Date: May 2008 Location: California Posts: 770 Trader Rating: (8) Feedback Score: 8 reviews	I love the new design and product! Looks like I have to add these to the PSM collection on the S13 when I come back in Feb! lets go to the track and test them out together! -Steve __________________ Tsuiso.Style @ Instagram

12-20-2010, 03:32 PM	#20
satek Leaky Injector Join Date: Jan 2010 Location: Vancouver BC Age: 30 Posts: 132 Trader Rating: (0) Feedback Score: 0 reviews	Just ordered mine!!

12-25-2010, 10:52 AM	#21
Bullet01 Zilvia Junkie Join Date: Apr 2005 Location: York, Pa Posts: 440 Trader Rating: (24) Feedback Score: 24 reviews	Any pics or info on your OEM modified tie rod ends?

12-30-2010, 04:17 PM	#22
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	POWERED BY MAX: Forums see the link for pictures, its OEM style since our super angle kit already spaces down the tie rod end. Also they last longer than ends with the bearing exposed. those are not released yet. __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

01-01-2011, 04:39 PM	#23
Datenshi Leaky Injector Join Date: Jul 2010 Location: Toronto Posts: 91 Trader Rating: (0) Feedback Score: 0 reviews	Wish these were out when I replaced my tie rods, would have bought them for sure. Good price, amazing guys and amazing products. +1 for PBM can't wait til spring to order full multi-link from you guys to go with these beautiful coils I got from you that I sadly have sitting on my desk to stare at and help winter go by faster. :P

01-01-2011, 05:01 PM	#24
PITCH Zilvia FREAK! Join Date: Jan 2006 Location: GA Age: 40 Posts: 1,103 Trader Rating: (5) Feedback Score: 5 reviews	Skid plate... Where can I buy? __________________

01-10-2011, 07:35 PM	#27
MIKE-240sx Join Date: Apr 2009 Location: Tdot Ohhhhhhhhh Age: 30 Posts: 27 Trader Rating: (1) Feedback Score: 1 reviews	orderd these a couple days ago, waiting for em to come in. +1 for affordable tie rods with free shipping! everyone should take advantage of this offer __________________ 1992 Nissan 240sx Project

01-26-2011, 03:41 PM	#28
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	there is too many [free] requests for shortening the tie rods, so we are now charging $15 for the labor to cut the length. __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

02-01-2011, 04:01 PM	#29
DC Dan MAX USA Zilvia.net Advertiser Join Date: Aug 2005 Location: San Diego Posts: 2,478 Trader Rating: (79) Feedback Score: 79 reviews	Sold out - We'll have more in march. __________________ How To order: You can order directly from our zilvia advertiser threads. When you add to cart, you get an instant shipping estimate, & the cart will remember all of your items as you move between forum threads and our website www.poweredbymax.net until you remove them or check out. I can also calculate estimates manually for you but the cart's estimates are way faster and more accurate. Order Inquiry: IM me your real name and paypal address. Thanks for your business!

03-20-2011, 09:43 PM	#30
eklipse38 Leaky Injector Join Date: Sep 2008 Location: tennessee Posts: 65 Trader Rating: (7) Feedback Score: 7 reviews	I have a set of the PBM tie rods paired with the Tein outers. I also have one of these steering spacers http://zilvia.net/f/suspension/36731...new-price.html. I had to cut about an inch off the PBM tie rods and after instaling and centering the rack spacer I have ran out of threads can i have the inners machined with more threads or should i just remove the rack spacer? I was able to set the toe before I instaled the spacer but now both sides are toed-in a ton.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode