c-los13

motor is a sr20det s13 blactop on s13 hatch, stock everything. i parked the car about 2 weeks since i was selling some old parts and getting new ones. before i parked the car it ran great. good idle, good mpg. i finally turned on the car last night. it turned on fine but a few minutes later it started throwning black smoke running super rich and shaking. i unplugged the maf and the BLACK smoke and shaking WAS gone. since i dont have an extra sr20 maf i did some rewiring and installed a sohc maf. Installed the sohc maf and same shit, throws smokes when plugged, stops when unplugged. PLEASEEEEEEEEEEEEEEEEEEEEEEEEEEE HHHHELLLLLPPPP. ANY INPUT WOULD BE GOOD.....

c-los13

Come on somebodys gotta know!!!

c-los13

Bbbbbbbuuuuummmmmmmmmmmmmmmpppppppppp

conrad_s13.5

without being able to source a known good maf its hard to say.

have any friends / locals that could drive over and lone u theirs for the 5mins itd take to check?

when its plugged in and all,. where do your rpms drop?

__________________
cONtRol FReAkS

sharpe_corners

I have a maf, 80 shipped 4 days to your door.

905 962 7498

[email protected]


Send me a text when your ready, I can ship out TODAY

!Zar!

Did you check for a leak in your intercooler pipes?

There is still a chance it could be a bad maf.

__________________

c-los13

Ima check the intercoller piping, also a mechanic said my air intake could have leak throwing off the readings. I hope I can get one of my friends to let me borrow his for a lil while. And to guy trynna sell me one, thanks and ill def let you know if I need it. Thanks a lot for the input everyone.

JDMRIDDAZ

coolant temp sensor..can do this
also a boost leak can do this

__________________
シチサｎ w/ka20det:in progress
シチサｎw/sr20det:stolen

Drft_S14

Ive had the same problem, I changed my MAF and it went away

__________________
I never narc'd on nobody

c-los13

Coolant temp sensor is fairly brand new. I got a friend stopping by today to let me borrow his maf. Ill update tonight.

RB24_S14

A bad ecu can do it too. Maybe moisture got on it or water drip down to the ecu. But the Maff could be it.

__________________
460whp 350Z

c-los13

Only thing in the back of my mind its the SOHC maf not working, I mean what are the odd ya know?? :/

c-los13

I forgot to mentioned that over the time I didn't drive the car it rained a lot and my windshield isn't sealed right. I thought about moisture too. Ima go home and open up the ecu to make sure is all dried as well. Would a bit of moisture ruin the ecu or can I fix it just by drying it up???? I can't wait to get outta work and do some test on the car

c-los13

Fml. I tried my friends maf (same motor). And the problem was still there. Decided to check out the ecu for any type of moisture and there it was! On one of the corners of the ecu there was some kinda dried up moisture where water may have landed. On the ecu connector and a small part on the pin out. I tried cleaning it up w an 'electrical cleaner' spray can. It looked good after the cleaning, I plugged it back in and same shit. FMFL. My ecu number is J4, I asked my friend to try out his ecu E5. The car would barely stay on. So now I can't tell if the ecu is bad or if maybe the water created a bad connection and burned out the wire that reads the maf since everything works fine unless the maf is plugged. I know this is long but I really need some help. A used J4 ecu is 250 bucks

c-los13

How can I check if the maf is getting any voltage??? I'm not sure if the ecu is bad or if the harness is.. Any input will be greatly appreciate

c-los13

I talked to one of guys at enthalphy (really nice ppl btw) he said to check voltage on the maf and on the ecu. I'm not experienced at all when it comes to wiring so I'm a bit confused. He said the 'black and white ' wire goin to the maf should read 12v. But what doesn't? Does it mean that the ecu is bad? Or maybe the ground for the maf got messed up?? I'm fucking clueless.

JDMRIDDAZ

Maf has 3 wires
12v
ground
ecu control wire...
TRY JDM OF MIAMI FOR ECU
LEGIT SELLER AND HAS EBAY STORE

__________________
シチサｎ w/ka20det:in progress
シチサｎw/sr20det:stolen

Darren

Make sure your maf plug is not plugged in backwards...

also.. if there WAS a problem and you FIXED it, you may want to pull your plugs and make sure they're not still SOILED, and that's what's currently causing the problems.

Good luck with the fix

c-los13

My only concern is what if is not the ecu? What if its the harness? Will do dome work on the car later today. Thanks

Darren

You could look into Wiring Specialties, they are reasonable and have a great product, they also have a harness repair service

Kingtal0n

What if the maf sensor is good but it is reading airflow that is not entering the engine?

I would do a boost leak check before buying any parts.

VNG704

Theres a j4 on zilvia right now for $50 or so. Though I haven't read the actual fs thread. An e5 wont work on your car if you need a j4. I think the mafs wiring are the same, have him use your mafs.

c-los13

I checked the plugs today and they were hella black. That explains why my friends maf didn't work. I put some old spark plugs and the car actually stayed on for a lil while without smoking. I tried revving in and it started smoking. I'm gonna buy new plug and try my friend maf again. Wish me luck. I got quote 300 from wiring specialist for a new harness to fit redtop ecus, just in case my ecu is fried. Gonna take off bumber and get a compressor to do a boost leak test as well. Damn I miss my car. I had just gotten stance coilovers and new wheels and this shit happened. Bummer from hell.

c-los13

Update: i got new spark plugs andrewired the single cam maf. Turned on car and let it idle for a while. No smoke til now. As soon as i revved it the black smoke started coming out again. I turned off the car right away cuz i didnt wann messed up my spark plugs again. So Pparently itsnot the maf help.

reallygood101

got the same problem wit my s14 sr20, i still havent found out wat it was and i put in new plugs, wrking maf, new tps, way better BOV, checked for leaks and still the same shit, i just got a wrking ecu in yesterday so im gonna b throwing that in and hopfully it wrks

c-los13

Sorry to hear that, i got better bov too (synapse), lmk if a new ecu fixes your problem since thats what im trying next. Thanks

reallygood101

update brotha, i put in the ecu i just got and the car is idling WAY better, no blck smoke and doesnt shake anymore and no breaks or back firing when reving it, so i would say get a new ecu... oh and also i replaced the IACV

c-los13

Alright. Yeah my iacv had calcium builup when i got the motor but i got it pretty cleaned up. I guess its time for a new ecu. I will update soon. Where did you get a new iacv?

reallygood101

i buy 95% of the stuff for my 240sx off the FS section so take some time and check it out you should find one fairly quick

c-los13

Update. Nobody around here had a j4 ecu so i ended up buying a brand new harness from wiring specialist ( yuri is great btw), and getting a redtop ecu from a friend. I installed evevything and turned on the car. It idled perfect for a lil whie and then it started again the damn black smoke again. I turned off the car because i didnt wanna ruin my brand new spark plugs (3rd ones). i also put a fuel gauge and the pressure its a 38 at idle. Wtf is going on? Im about to give up. When i took off one of the plugs i could see a bit of black smokecoming out still. What could it be? I pull the codes from the ecu and it gave me 55. Help please. I need my car really bad