180sx position/bumper light install - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

ALEXTHESUS*PECT · 12-26-2007, 03:37 PM

when you get a kit or change to a type x front bumper you will need to wire in the front bumper turn signals. here is everthing needed:

housings:

new bulb harnesses:

you will also need wire cutters, electrical tape, and soldering gun if you have one.

start off by pulling out the harness on the car for the bumper light and cut it off.

as you can see there are 3 wires; black, green/yellow, red/blue. strip the covering from the two colored wires, and then again on the new light harness. i trimmed the black and taped it over by itself with the electrical tape. then coneect the old light harness and then new one:

plug in the bulb and make sure it works for the driving lights and blinks for turn signals.

Tape everything back up, and tuck back in the harness into the bumper. put the new bulb into the new bumper light, and you are all done!

mr_240sx · 12-26-2007, 09:36 PM

are you serious? i thought i could only have either turn signal or running lights.... you sure it works with the ground un hooked?

tks a bunch, ill go try that next time im working on the car!

ALEXTHESUS*PECT · 12-26-2007, 09:39 PM

yeah i'm sure. if you use the black/ground then only one will work. but if use both the colored wires then they both work.

mr_240sx · 12-26-2007, 09:50 PM

tks Alex, ill try this out next time i work on the car!

A Spec Products · 12-27-2007, 08:45 PM

Yeah

I did it the same way

So it lights up in on position but still blinks when turn signals are on

I didn't buy the actual harnesses though (Origin markers only come with the housings, no bulbs/sockets/harness), I just used rear side marker bulb socket/harness that I trimmed to fit

mr_240sx · 12-28-2007, 12:02 AM

i hooked it up this way tonight and its true, it works for both positioning lights and flashers.....the only thing is i found it flashed differently now. how can i say it, it has some sort of unpredictable flashing now. itll flash 4 imes the same speed then 1-2 times really quick and then goes back to normal and it continues doing that. i found it only does that when i have lights turned on. when lights are off the signals are fine!

ALEXTHESUS*PECT · 01-07-2008, 10:03 PM

Quote:

Originally Posted by mr_240sx

i hooked it up this way tonight and its true, it works for both positioning lights and flashers.....the only thing is i found it flashed differently now. how can i say it, it has some sort of unpredictable flashing now. itll flash 4 imes the same speed then 1-2 times really quick and then goes back to normal and it continues doing that. i found it only does that when i have lights turned on. when lights are off the signals are fine!

not sure why. i didn't have this problem.

btw how come this isn't approved yet?

mr_240sx · 01-07-2008, 11:18 PM

all i know is this has been performed and it works! youve got my thumbs up for you Alex!

powersteeringless180sx · 02-11-2008, 11:26 AM

aww shit i never knew you could do this.... i just spliced the wires from the front sidemarkers but i'm gonna do this instead cuz i don't have blinkers in the front. +1!!

kousuke180sx · 03-14-2008, 04:38 PM

I tried this today and it worked perfectly, thanks alot!

12-26-2007, 03:37 PM	#1
ALEXTHESUSPECT Post Whore! Join Date: Oct 2005 Location: Soul cal!! Age: 43 Posts: 4,387 Trader Rating: (5) Rides Gallery: ALEXTHESUSPECT Feedback Score: 5 reviews	180sx position/bumper light install when you get a kit or change to a type x front bumper you will need to wire in the front bumper turn signals. here is everthing needed: housings: new bulb harnesses: you will also need wire cutters, electrical tape, and soldering gun if you have one. start off by pulling out the harness on the car for the bumper light and cut it off. as you can see there are 3 wires; black, green/yellow, red/blue. strip the covering from the two colored wires, and then again on the new light harness. i trimmed the black and taped it over by itself with the electrical tape. then coneect the old light harness and then new one: plug in the bulb and make sure it works for the driving lights and blinks for turn signals. Tape everything back up, and tuck back in the harness into the bumper. put the new bulb into the new bumper light, and you are all done! __________________ *TEAM SUSPECT**

12-26-2007, 09:39 PM	#3
ALEXTHESUSPECT Post Whore! Join Date: Oct 2005 Location: Soul cal!! Age: 43 Posts: 4,387 Trader Rating: (5) Rides Gallery: ALEXTHESUSPECT Feedback Score: 5 reviews	yeah i'm sure. if you use the black/ground then only one will work. but if use both the colored wires then they both work. __________________ *TEAM SUSPECT**

12-27-2007, 08:45 PM	#5
A Spec Products Post Whore! Join Date: Mar 2005 Location: Socal! Off 60/605 Posts: 7,256 Trader Rating: (27) Feedback Score: 27 reviews	Yeah I did it the same way So it lights up in on position but still blinks when turn signals are on I didn't buy the actual harnesses though (Origin markers only come with the housings, no bulbs/sockets/harness), I just used rear side marker bulb socket/harness that I trimmed to fit __________________ A SPEC PRODUCTS CORP AME Wheels, Advan, ARC, Gram Lights, Nardi, Personal, Recaro, Works Bell, Work Wheels, Volk Racing, 5Zigen, & more! 626.618.1100 x 103 / aim: aspectuan Advertiser's Specials! Read / Give Feedback! Please Rate Us!

03-14-2008, 04:38 PM	#10
kousuke180sx Zilvia Junkie Join Date: Oct 2004 Location: SOCAL 714 Posts: 304 Trader Rating: (3) Feedback Score: 3 reviews	I tried this today and it worked perfectly, thanks alot! __________________ *Signature exceeds forum limit

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-26-2007, 09:36 PM	#2
mr_240sx Post Whore! Join Date: Nov 2004 Location: Ottawa Age: 35 Posts: 6,320 Trader Rating: (4) Rides Gallery: mr_240sx Feedback Score: 4 reviews	are you serious? i thought i could only have either turn signal or running lights.... you sure it works with the ground un hooked? tks a bunch, ill go try that next time im working on the car!

12-26-2007, 09:50 PM	#4
mr_240sx Post Whore! Join Date: Nov 2004 Location: Ottawa Age: 35 Posts: 6,320 Trader Rating: (4) Rides Gallery: mr_240sx Feedback Score: 4 reviews	tks Alex, ill try this out next time i work on the car!

12-28-2007, 12:02 AM	#6
mr_240sx Post Whore! Join Date: Nov 2004 Location: Ottawa Age: 35 Posts: 6,320 Trader Rating: (4) Rides Gallery: mr_240sx Feedback Score: 4 reviews	i hooked it up this way tonight and its true, it works for both positioning lights and flashers.....the only thing is i found it flashed differently now. how can i say it, it has some sort of unpredictable flashing now. itll flash 4 imes the same speed then 1-2 times really quick and then goes back to normal and it continues doing that. i found it only does that when i have lights turned on. when lights are off the signals are fine!

01-07-2008, 11:18 PM	#8
mr_240sx Post Whore! Join Date: Nov 2004 Location: Ottawa Age: 35 Posts: 6,320 Trader Rating: (4) Rides Gallery: mr_240sx Feedback Score: 4 reviews	all i know is this has been performed and it works! youve got my thumbs up for you Alex!

02-11-2008, 11:26 AM	#9
powersteeringless180sx Zilvia Addict Join Date: Mar 2006 Location: SoCal (Orange County) Age: 40 Posts: 868 Trader Rating: (1) Feedback Score: 1 reviews	aww shit i never knew you could do this.... i just spliced the wires from the front sidemarkers but i'm gonna do this instead cuz i don't have blinkers in the front. +1!!