Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Chat

Chat General Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 05-12-2004, 11:28 PM   #1
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
KA-T progress report, Day 1 (56K might not make it)

may 12th, 2004

http://www.imagestation.com/album/?id=4286888263&idx=9

Log:


my turbo stuff.. all of these will go into the car minus the stock SR SMIC.


Took off the hood and jacked the car up.


FMIC in place.. its the same exact size as the blitz FMIC but I forgot the brand.. its some japanese brand.


test fitted the infamous ETD manifold.


Closer look.


Pretty good turbo/brake master cyl clearance.

setup
370cc injectors - installed (prolly gonna need to find one more 370cc, I used KA plastic cap on one of the injectors)
Walbro fuel pump - installed
Cobra MAF
JWT ECU
ETD manifold
T3 super 60, .63 turbine A/R
Tial 38mm WG (4psi spring for now)
Turbo XS BOV
JGS oil lines & fittings
custom 2.5 inch IC pipings
custom 3 inch downpipe
Greddy boost gauge
Wideband O2 (soon from streetrays)
SAFC 2 (soon from ebay)

Tommorrow we're going to try and work on the pipings + downpipe. Hopefully we can get the car running by the end of this week.

I am also going to use the ETD manifold as is... I am going to test and see how long this manifold will hold. (my guess will be a couple of months if im lucky).
I am not going to reweld the weldings and gaps... prolly gonna do some grindings to smooth things out a bit but thats it.
I am not really satisfied with the quality but I like the design. I am going to be looking for another manifold (not ETD) to replace this ETD one after the car runs.

stay tuned
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Sponsored Links
Old 05-12-2004, 11:29 PM   #2
Dousan_PG
Post Whore!
 
Dousan_PG's Avatar
 
Join Date: May 2002
Location: Orange County, California
Age: 42
Posts: 16,640
Trader Rating: (23)
Dousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfectionDousan_PG is close to perfection
Feedback Score: 23 reviews
that intercooler is ridiculous huge
good luck on the project!woot
__________________
Aaron
Pink GodziRa
www.geocities.com/pink_godzira
Dousan_PG is offline   Reply With Quote
Old 05-12-2004, 11:31 PM   #3
SilviaDriver
Post Whore!
 
SilviaDriver's Avatar
 
Join Date: Jun 2002
Location: San Jose, CA
Age: 36
Posts: 5,514
Trader Rating: (2)
SilviaDriver will become famous soon enoughSilviaDriver will become famous soon enoughSilviaDriver will become famous soon enoughSilviaDriver will become famous soon enough
Feedback Score: 2 reviews
Send a message via AIM to SilviaDriver
good shit Rey! damn..i remember back when we was talkin bout this project togher..

y the fuck wont u IM me no more u lil bitch!

good luck on ur shit tho! looking forward to seeing Okes setup as well

aye IM me on how much it all cost u..if u have a problem with posting up how much u spent
SilviaDriver is offline   Reply With Quote
Old 05-13-2004, 12:14 AM   #4
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
man.. the forum is all messed up tonight.. (at least from my computer)..

but yea so far i've spent ~1500 and this will go up again once I purchase a wideband and safc2 and some other cool stuff...
plus I still have to finish up my suspensions. I need rear arms..
Tommorrow will be interesting though... cuz welding and making custom stuff is a lot of fun... especially if you CANT [email protected]@!!
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-13-2004, 03:18 PM   #5
No Motiv
Zilvia FREAK!
 
No Motiv's Avatar
 
Join Date: May 2003
Location: Silver Spring, MD
Posts: 1,189
Trader Rating: (0)
No Motiv is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to No Motiv
nice S13 ka-t setup....fuck sr
__________________
-Austin


My name is Shake-Zula, the mic rulah, the old schoolah, you wanna trip, I'll break it to ya. Frylock and I'm on top rock you like a cop, Meatwad you're up next with your knock-knock. Meatwad make the money see, Meatwad get the honeys G. Drivin in my car, livin like a star, ice on my fingers and my toes and I'm a Taurus. Cause we are the Aqua Teens, make the homeys say ho and the girlies wanna scream.
No Motiv is offline   Reply With Quote
Old 05-13-2004, 03:23 PM   #6
boosteds14
Zilvia.net Advertiser
 
boosteds14's Avatar
 
Join Date: Jan 2002
Location: CIPmotorsports
Age: 39
Posts: 1,612
Trader Rating: (0)
boosteds14 will become famous soon enoughboosteds14 will become famous soon enoughboosteds14 will become famous soon enoughboosteds14 will become famous soon enoughboosteds14 will become famous soon enough
Feedback Score: 0 reviews
Send a message via AIM to boosteds14
very nice and impressive....You have my approval
great job, keep up the good work.
__________________
240SXONE

www.240SXMOTORING.com --- One Stop Shop for Your Nissan 240sx
boosteds14 is offline   Reply With Quote
Old 05-13-2004, 04:10 PM   #7
gmckey
Zilvia Junkie
 
Join Date: Feb 2003
Location: Austin, Tx
Posts: 301
Trader Rating: (0)
gmckey is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to gmckey
WOW MAN!

looking great!

Don't guess you'll be at Grind101 on the 30th by any chance

that turbo looks big man, guess it might just be the way it's mounted... come down to Austin and run LCR w/ me.
gmckey is offline   Reply With Quote
Old 05-13-2004, 06:13 PM   #8
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
yea thanks for the comments guys... We're trying to get this done by sunday...
Today wasnt really a productive day for us.. It rained all day long...
so we only did a couple of things:

Installed project silvia 3 inch downpipe and JGY's 3 inch test pipe
Removing the oil pan to get it tapped
Installed JWT ECU
Installed JGS oil feed line
Ate some ice cream

Tommorrow, we will measure, cut, and mark the IC pipings and the downpipe
Saturday we're going to a friend's place to get them welded, weld a bung to the oil pan, make a custom inlet bell.

and hopefully sunday we will be able to hook everything up and get the car running.

gmckey - LCR sounds like fun man , but yea I'll be at the grind 101 although im not going to run that much since I going to be a staff.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-13-2004, 06:36 PM   #9
1998cc
Leaky Injector
 
Join Date: Dec 2002
Location: Colorado
Posts: 89
Trader Rating: (0)
1998cc is an unknown quantity at this point
Feedback Score: 0 reviews
thats a nice ka-t. Your setup is pretty similar to mine. I just have the iap manifold. Good Luck and keep it running strong!
__________________
Pop-ups Rock
1998cc is offline   Reply With Quote
Old 05-14-2004, 07:40 AM   #10
CoasTek240
Post Whore!
 
CoasTek240's Avatar
 
Join Date: Jan 2002
Location: VA
Age: 36
Posts: 3,034
Trader Rating: (3)
CoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud ofCoasTek240 has much to be proud of
Feedback Score: 3 reviews
Send a message via AIM to CoasTek240
well done

well done man. that thing looks like its gonna haul!...keep us updated
CoasTek240 is offline   Reply With Quote
Old 05-14-2004, 11:28 AM   #11
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
I think i might get IAP manifold or maybe phat-kat's, cuz i dont think this ETD manifold will hold. the weldings is pretty from the outside but when you look at the collectors inside, its a whole different story..

I will take more pictures either today or tommorrow and keep y'all updated... especially if we run into some problems
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-14-2004, 11:49 AM   #12
Powashiftin
Zilvia Junkie
 
Join Date: Dec 2002
Location: Northern NJ
Posts: 416
Trader Rating: (0)
Powashiftin is an unknown quantity at this point
Feedback Score: 0 reviews
you've only spent 1500 and you have all that stuff?
__________________
http://www.tempusband.com
Powashiftin is offline   Reply With Quote
Old 05-14-2004, 12:11 PM   #13
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
groupbuys
and thats also the reason why it took me so long to gather all of these parts (almost a year).
Originally I planned to go with 14b.. but then I found T3 super 60 and I cant pass that deal.
the most i've spent so far is for the JWT ecu, that thing is expensive... I've I were to start again.. i'd ditch the JWT. SAFC + wideband o2 are adequate enough IMO
A lot of the small stuff I got (couplings and all that), I got some from friends.. those little stuff can add up to 250-300 bux easy if you cant find any thats free.
But im pretty sure the total will be over 2000 after this is done cuz i still have to buy some pipes+hoses+3 inch cat-back exhaus.. etc etc..
I'll try to make a table of the stuff i got and their prices once everything is done...
Im pretty sure i will be surprised.. cuz my original budget for this is only 1000.. and im well over my planned budget now...
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-15-2004, 03:41 AM   #14
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
we started the day off with taking the I/C pipings off from my buddy's (240_keyy) S13 SR.
He has a blitz I/C kit.


After a bit of measuring and test fitting, we decided to make the blitz pipings for mock up.

The blitz coldpipe

this is the upper coldpipe. the lower coldpipe also fits (but I forgot to take some pictures of it.

As for the hotpipe, the lower blitz hotpipe seems to fit also ,prolly with slight modification since we fabbed our own upper hotpipe.


Dont ask about the bent hook,happenned 2 years ago... long story.... rain+hydroplane=curb



the intake pipe design looks kinda funky because thats the only compressor inlet bell that I have (its bent in a strange angle).
However, with that design, we think it will clear the hood. its just that Im not really a fan of those bends...

So tommorrow, We're going to make a new custom inlet bell so we can make the intake flow better.
We will also make the I/C pipings (Lower hotpipe, Upper and Lower coldpipe) using my buddy's blitz kit as a mock up.
Also lets not forget the downpipe.
We spent hours trying to fit and measure the downpipe. The downpipe is connected with ducttape right now but we're going to weld it too tommorrow.
We'll see how it goes.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-16-2004, 12:15 AM   #15
INeedNewTires
Zilvia FREAK!
 
INeedNewTires's Avatar
 
Join Date: May 2003
Location: Austin, TX
Posts: 1,527
Trader Rating: (4)
INeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond reputeINeedNewTires has a reputation beyond repute
Feedback Score: 4 reviews
hell yea, FUck SR, glad to see another KAT in on the road. Im in houston man, do you ever go to the college station autoX's? Ive been to a few and dont think ive ever seen you there. good luck w/ the project, keep us posted i wanna see some numbers when your done.
__________________
INeedNewTires is offline   Reply With Quote
Old 05-16-2004, 12:46 AM   #16
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
If the pictures didnt show up, click refresh.
if still not working, right click on the 'red X' and click 'show picture'.

Imagestation sucks.. I need to find another host. but hopefully my website will be running mid-summer and Im going to document all of this stuff there.

So today we went to Cuero, TX... about 2.5 hours from Southwest of college station. Cuero is my buddy's hometown and he has a friend that has a welding machine and he can weld.

so basically these are what we have right now.


the heart of fury... the infamous beater EF that drove us down to Cuero


Raw materials. 4 U-bends, 1 Straight

The aluminum piping in the picture is my buddy's blitz piping kit. we used these as a mock up.


Brian working his magic.


The downpipe (80% done)


Jeff (left) making some flanges, and Brian (right) welding my downpipe together.


The finished products. Notice that the pipings in the front are my custom pipings and the 3 piping behind them is the blitz I/C piping kit.
So my I/C pipings are done: Upper coldpipie, Lower coldpipie, lower hotpipe, upper hotpipe, wastegate flange+dump pipe, custom compressor inlet bell.
the downpipe is 85% done, we still need to fit the bottom 3 bolt flange on to it. The oilpan was also tapped and a bung was welded on to it.


oh and Jeff gave me this... this will be perfect for my custom oil cooler

complete album
http://www.imagestation.com/album/?id=4286888263

Remember if the pictures didnt show up, click refresh or right click on the red 'X' and click 'show picture'


Projex240 : the downtime for my jwt ecu reprogram is a little over 1.5 months. I sent my other ECU i got from my friend so theres not really any downtime for me. I got it reprogrammed through JGYcustoms.com. I highly recommend them. great people!

as for the pipings, we used U bends.
for the I/C pipings alone, we used one U bends and cut it in two pieces, weld them in such angle and thats it. pretty simple...
I did all of the cutting and my friend brian did all of the welding.
So we only used a total of three (3) U-bends to make this I/C piping.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-16-2004, 12:52 AM   #17
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
Quote:
Originally Posted by INeedNewTires
hell yea, FUck SR, glad to see another KAT in on the road. Im in houston man, do you ever go to the college station autoX's? Ive been to a few and dont think ive ever seen you there. good luck w/ the project, keep us posted i wanna see some numbers when your done.
Yea man I'm tamscc member and I do autocross in the riverside annex.
I've been autocrossing with the club for 3 years now. although I missed a couple of autoXes this past spring semester.

I'm always in SSM. just look for me whenever you're at the autocross again...
I always park right next to two other 240s, White hatch with blackroof (SR), and champagne hatch with RSR ex mag exhaust.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-16-2004, 02:21 AM   #18
240Driver39
Zilvia FREAK!
 
Join Date: May 2002
Location: Charleston, SC
Age: 36
Posts: 1,076
Trader Rating: (1)
240Driver39 is making a name for him/her self240Driver39 is making a name for him/her self
Feedback Score: 1 reviews
Send a message via AIM to 240Driver39
awesome man, im jealous..and lookin forward to hearin ur opinions on ur setup
__________________
1991 240sx SE, 5spd fastback
240Driver39 is offline   Reply With Quote
Old 05-16-2004, 08:35 AM   #19
Zemus
Nissanaholic!
 
Zemus's Avatar
 
Join Date: Oct 2001
Location: Minneapols
Age: 37
Posts: 2,268
Trader Rating: (0)
Zemus is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to Zemus
Those are some awesome wheels, what kind are they? Your setup sounds awesome, cant wait to see how it turns out
Zemus is offline   Reply With Quote
Old 05-16-2004, 08:41 AM   #20
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
thanks man..
Those wheels are
SSR Hiro
F: 16x7 +27
R: 16x8 +30
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-16-2004, 11:58 PM   #21
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
First of all I'm sorry if I keep updating this thread.. I just dont want to make new threads for the same stuff...


Yep... Day 5.. we've been slacking off and the KA-T hadnt seen the road yet...
BUT.. we got it started tonight and observed it. It seems like everything is running good except that its running rich. We also notice that the cobra maf is so sensitive.. slight wind messed up the idle.
We covered the mafs with my flat K&N and it idles great.
We revved it up and man.. the whinning turbo sound was just beautiful... we're still running open downpipe...

Here's some pictures..



Lower hotpipe hooked up


Lower coldpipe hooked up


Ghetto rigged radiator hose... Im not really a fan of it but the I/C pipings made us do it...
I'm going to do something about it for sure.


Intake & BOV


the oil feed fittings is leaking... thats because we havent put some teflon tape in the thread yet.. gonna do that tommorrow..
Checked everything else and no leaks so far..
We'll know more tommorrow when we drive it.. whether it has some boost leak or not.

well thats it for tonight.
Hopefully tommorrow we're can get to drive it.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-17-2004, 01:16 AM   #22
Flybert
Post Whore!
 
Join Date: Mar 2003
Location: none
Posts: 3,862
Trader Rating: (7)
Flybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfectionFlybert is close to perfection
Feedback Score: 7 reviews
Super badass. Did you get the SAFC already?
Flybert is offline   Reply With Quote
Old 05-17-2004, 02:24 AM   #23
TurboB15sentra
Zilvia Member
 
Join Date: Apr 2003
Location: New Orleans, LA
Age: 41
Posts: 258
Trader Rating: (0)
TurboB15sentra is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to TurboB15sentra
Quote:
Originally Posted by Bbandit
Yea man I'm tamscc member and I do autocross in the riverside annex.
I've been autocrossing with the club for 3 years now. although I missed a couple of autoXes this past spring semester.

I'm always in SSM. just look for me whenever you're at the autocross again...
I always park right next to two other 240s, White hatch with blackroof (SR), and champagne hatch with RSR ex mag exhaust.
Hey, do you have anymore pics or info on those rims? How wide are the rears and what size tire can you fit on them? I need a rim that will fit a 26 x 10" slick..

Travis
__________________
www.fi-r.net
Nissan Performance
TurboB15sentra is offline   Reply With Quote
Old 05-17-2004, 03:44 AM   #24
240Stilo
Junkie
 
240Stilo's Avatar
 
Join Date: May 2002
Location: Socal
Age: 37
Posts: 1,160
Trader Rating: (0)
240Stilo is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to 240Stilo
How many miles on the KA?
__________________
-Juan
240Stilo is offline   Reply With Quote
Old 05-17-2004, 07:16 AM   #25
Bbandit
Post Whore!
 
Bbandit's Avatar
 
Join Date: Mar 2002
Location: Texas and now Jakarta
Age: 39
Posts: 2,674
Trader Rating: (0)
Bbandit is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via ICQ to Bbandit Send a message via AIM to Bbandit
no SAFC yet, but I surely need one so Im gonna get one by the end of this week when I get paid.

The rear wheels are 8 inch wide. Im using 50/225/ R16 size tires.

The KA in my coupe came from a 95 S14, ~100k miles. I'm going to rebuild my 91 KA (currently 172,000 miles) for future usage.
__________________

==>>TGL GARAGE<<==.. RIP!
S13 coupe KA-T @ 0.5 Bar = SOLD!
A31 Cefiro + SR = Current
Bbandit is offline   Reply With Quote
Old 05-17-2004, 12:17 PM   #26
mellojoe
Zilvia Junkie
 
Join Date: Jan 2004
Location: ARKANSAS
Posts: 518
Trader Rating: (0)
mellojoe is an unknown quantity at this point
Feedback Score: 0 reviews
good stuff! I'm jealous.

Ghetto fab all the way! Can't wait to see the final result and the final build tally.
__________________
mellojoe is offline   Reply With Quote
Old 05-17-2004, 12:57 PM   #27
Aids333
 
Join Date: Jun 2003
Location: new york
Posts: 6
Trader Rating: (0)
Aids333 is an unknown quantity at this point
Feedback Score: 0 reviews
good luck today man hope everything works well...
p.s. how much did you get that IC for?
Aids333 is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 06:57 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™