Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Chat

Chat General Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 05-22-2005, 09:49 AM   #1
SxMachine
Zilvia Member
 
SxMachine's Avatar
 
Join Date: Sep 2002
Location: Jerzie2Atl, Ga
Posts: 181
Trader Rating: (0)
SxMachine is making a name for him/her selfSxMachine is making a name for him/her selfSxMachine is making a name for him/her self
Feedback Score: 0 reviews
Turbo installation instructions in 4 steps

Maybe its common knowledge for some but not for others:
TURBO INSTALLATION INSTRUCTIONS

How to install a turbocharger in four easy steps.
Anyone can install a turbo charger. Here's how.


--------------------------------------------------------------------------------

You must change oil lines prior to installing all turbos

--------------------------------------------------------------------------------

(1) PRE-INSTALLATION
Service air cleaners and eliminate all restrictions and leaks
Before installing turbocharger, inspect and remove all foreign material from air inlet ducting and intake and exhause manifolds.
Replace all oil pressure and drain lines which could be kinked, broken, heat worn or internally damaged.
Change engine oil and oil filters.
Replace all contaminated crankcase and compressor filters.

--------------------------------------------------------------------------------

(2) PRE-LUBRICATION
Before attaching new oil drain line to turbocharger, CRANK ENGINE until oil flows from oil drain hole in bearing housing. DO NOT START ENGINE.
Attach NEW oil drain line to turbocharger.

--------------------------------------------------------------------------------

(3) INSTALLATION
Mount turbocharger and exhaust manifold using new gasket (avoid using sealing material).
Inspect exhaust system. Remove any restrictions which might cause excessive back pressure before connecting to turbocharger.
Attach NEW oil inlet line to turbocharger.
Align bearing housing drain hole to not more than 30º from vertical center position.
Tighten clamps, capscrews or nuts to recommended specifications.
Connect air pipage system to turbocharger.

--------------------------------------------------------------------------------

(4) OPERATION
Idle engine for 5 minutes. DO NOT REV.
Check all systems for oil, air or exhaust leaks.
Always have operator IDLE ENGINE for 1 minute PRIOR to SHUTDOWN for longer turbocharger life.

http://www.actionsalvage.com/turboinstructions.htm
__________________
91 Bmw 318is
90 S13 (sr20det)
SxMachine is offline   Reply With Quote
Sponsored Links
Old 05-22-2005, 12:12 PM   #2
WILDACEX187
Post Whore!
 
WILDACEX187's Avatar
 
Join Date: Jan 2003
Location: QUEENZ, NYC
Age: 38
Posts: 3,103
Trader Rating: (4)
WILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond reputeWILDACEX187 has a reputation beyond repute
Feedback Score: 4 reviews
Send a message via AIM to WILDACEX187
are the oil drain lines the same as turbo oil lines like the ones u get from taka?
__________________
SR POWA COUPE LUVVV!!!
WILDACEX187 is offline   Reply With Quote
Old 05-22-2005, 01:10 PM   #3
SxMachine
Zilvia Member
 
SxMachine's Avatar
 
Join Date: Sep 2002
Location: Jerzie2Atl, Ga
Posts: 181
Trader Rating: (0)
SxMachine is making a name for him/her selfSxMachine is making a name for him/her selfSxMachine is making a name for him/her self
Feedback Score: 0 reviews
???
I was just droppin some info for those who don't know. Stumbled on that site by mistake (no connection to the SxMachine). Some FYI for turbo newbs, thats all.
__________________
91 Bmw 318is
90 S13 (sr20det)
SxMachine is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 05:11 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™