Wiring s13 redtop sr20 to S14 chassis for air conditioning. - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

thatkevv · 06-27-2015, 09:29 AM

So I am attempting to get the air conditioning going on my s14 with an redtop sr20 swap. Iv already done all of the required mods except the wiring. I am to the understanding that I need to connect the Yellow/Black to Black/Pink on the KA's F3 plug. Well do I connect these wirings directly off the plug? I'm not sure which way to connect them on the harness. Done some research and haven't gotten a definite answer. If anyone has some experience in this I'd appreciate some help! Thanks.

(SOLVED)

thatkevv · 06-27-2015, 03:11 PM

Would I loop the wires directly off of the connector?

roorr0 · 07-20-2015, 06:09 AM

Did you ever figure the solution??

thatkevv · 07-20-2015, 08:54 AM

I have not. I just looped it on the connector for now. I couldn't figure it out by looking at a wiring diagram because it doesn't show the other pin on the diagram. Once I actually get it all running I will post up and let you know if it works or not!

thatkevv · 08-06-2015, 02:07 PM

To get the AC wiring to work. You indeed just loop the yellow/black and the black/pink wires together directly off of the F3 plug in the passenger footwell behind the ecu. That way it grounds the triple pressure switch from the AC button on the dash instead of the ka's ecu doing it. That simple. Hope this helps.

*TheRealSy90* · 08-06-2015, 05:17 PM

Wouldn't a wiring specialties harness make everything work correctly as if it was oem?

thatkevv · 08-06-2015, 06:12 PM

You have to modify the body harness more less. And I don't have a wiring specialties harness so I wouldn't know. I'd imagine it wouldn't.

omgosh · 08-07-2015, 01:09 AM

If you just do the yellow/black black/pink you lose some functions, A/C wont turn off when you floor it, and it could freeze over..

You can make it work like factory if you do a little more wiring.

You have to run wires from the ECU pins for A/C relay, A/C hand switch, pressure switch, and thermo-control amp wires to the F3 plug. I used the A/C compressor plug wire on the SR engine harness (blue/red) and ran it to the FICD solenoid so it still kicks up the idle. The rest of the wiring is already there in the body harness on the USDM S14. Just plug the factory plug into the compressor.

thatkevv · 08-07-2015, 05:15 AM

Yeah that's the one thing you have to look out for. But I'll just turn it off when I go high Rpms.

06-27-2015, 09:29 AM	#1
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	Wiring s13 redtop sr20 to S14 chassis for air conditioning. So I am attempting to get the air conditioning going on my s14 with an redtop sr20 swap. Iv already done all of the required mods except the wiring. I am to the understanding that I need to connect the Yellow/Black to Black/Pink on the KA's F3 plug. Well do I connect these wirings directly off the plug? I'm not sure which way to connect them on the harness. Done some research and haven't gotten a definite answer. If anyone has some experience in this I'd appreciate some help! Thanks. (SOLVED) Last edited by thatkevv; 08-06-2015 at 02:03 PM..

08-07-2015, 01:09 AM	#8
omgosh Zilvia Member Join Date: Mar 2005 Location: Tampa FL Posts: 210 Trader Rating: (0) Feedback Score: 0 reviews	If you just do the yellow/black black/pink you lose some functions, A/C wont turn off when you floor it, and it could freeze over.. You can make it work like factory if you do a little more wiring. You have to run wires from the ECU pins for A/C relay, A/C hand switch, pressure switch, and thermo-control amp wires to the F3 plug. I used the A/C compressor plug wire on the SR engine harness (blue/red) and ran it to the FICD solenoid so it still kicks up the idle. The rest of the wiring is already there in the body harness on the USDM S14. Just plug the factory plug into the compressor. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-27-2015, 03:11 PM	#2
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	Would I loop the wires directly off of the connector?

07-20-2015, 06:09 AM	#3
roorr0 Zilvia Junkie Join Date: Apr 2006 Location: Vee-Aye Posts: 366 Trader Rating: (9) Feedback Score: 9 reviews	Did you ever figure the solution??

07-20-2015, 08:54 AM	#4
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	I have not. I just looped it on the connector for now. I couldn't figure it out by looking at a wiring diagram because it doesn't show the other pin on the diagram. Once I actually get it all running I will post up and let you know if it works or not!

08-06-2015, 02:07 PM	#5
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	To get the AC wiring to work. You indeed just loop the yellow/black and the black/pink wires together directly off of the F3 plug in the passenger footwell behind the ecu. That way it grounds the triple pressure switch from the AC button on the dash instead of the ka's ecu doing it. That simple. Hope this helps.

08-06-2015, 06:12 PM	#7
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	You have to modify the body harness more less. And I don't have a wiring specialties harness so I wouldn't know. I'd imagine it wouldn't.

08-07-2015, 05:15 AM	#9
thatkevv Join Date: Aug 2012 Location: stl Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	Yeah that's the one thing you have to look out for. But I'll just turn it off when I go high Rpms.