Re-Build with new colors - Progress pics - Page 26 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

heiyuu · 06-27-2015, 02:17 AM

May I ask what kinda floor sealer did you use on the garage and where u got it from?

kuruptR · 07-16-2015, 12:15 AM

Weight Reduction and Chassis Prep Phase 1

I cut out the holes and dimpled them leaving the swiss cheesed sheet metal rigid.

One hole aint do much, but many of them...still not much. Im pinching for lbs so everything will count in the end. I dimpled and drilled out a 1 1/2" hole, using a bolt driven die.

Brackets, reinforcement plates, and other miscellaneous bracing have been drilled out with a spot weld drill bit (not pictured). I drilled through to the outside several times, I will have to go back weld in what holes I made.

Once everything has been removed, I have began to remove all sound deadening, adhesives, and paint and primers. A heat gun was used for the deadening that was stubborn, and finished off with acetone and a lot of old microfiber cloths.

I started a small section with aircraft paint stripper, with all the crevices it was difficult to scrape off. Also, it was not effective at going through the layers of paint. The car was originally red then painted black, so thats 2 coats of primer and 2 of paint. I noticed the aircraft stripper was not strong enough to penetrate through the primers. I switched the method to mechanical, scotch brite pads have been effective in the past but on a larger scale, using the large pads on an angle grinder. I used only 4 pads to get it to the stage pictured above, 4 pads @ $5.00 each. Left a very clean and smooth finish without warping or damaging the metal, I will finish the the rest with brush on aircraft stripper.

Factory gas tank removal, theres a little fuel remaining so for safety I have removed it.

The spare tire well will not be needed, It will give me a better view on how I want to mount the new fuel tank.

I will be rolling out a new trunk pan, but it will come after planning the fuel system and wing layout.

When Im finished this prep I will either begin to prep the cage for welding or Ill do the fuel system. I need to pickup a few things, a bead roller to do the floors, a tube notcher to notch the tubing for the cage and the fuel stuff.

turbo2nr · 07-16-2015, 05:14 AM

WOW amazing stuff. +1 for privateers! I cant wait to see the next steps. Plan on removing the drive' side hump on the floor so you can mount your seat better?

Keep it up man!

skun · 08-03-2015, 07:53 PM

Following this thread since you started it and every year this project goes better!!

One question about SSR´s, the sizes you have was 18x9 +8, 18x10 +8 but they was specially ordered for you under your sizes specifications or maybe you used spacers?
Coz I can not find this sizes at SSR website

Thanks!!!

CamryOnBronze · 08-04-2015, 08:04 AM

Looking good!

dizzariot · 10-21-2015, 06:59 PM

Sub'd. So happy this is back in my life.

*tacotacotaco* · 12-12-2015, 12:25 PM

Any New updates?

OutlawLui · 12-12-2015, 12:34 PM

Quote:

Originally Posted by tacotacotaco

Any New updates?

Why you gotta bump the thread

I was exite for a sec

lilcim · 01-17-2016, 12:26 PM

I need to drive down from Quebec to see and hang S13 pals. OMG can't wait to see the next version of it.

Pblesh85 · 06-26-2016, 11:38 AM

I am curious to see how this is progressing or if it was parted/sold like the rest of the interesting builds on here.

CamryOnBronze · 06-27-2016, 07:44 AM

Quote:

Originally Posted by Pblesh85

I am curious to see how this is progressing or if it was parted/sold like the rest of the interesting builds on here.

He still has it. Plugging away as life allows if I am not mistaken. But if you had a couple of Porches to play with, would you want to work on this? lol

ellopuppet · 06-27-2016, 07:55 AM

Quote:

Originally Posted by evilpanamajack

Why you gotta bump the thread

I was exite for a sec

This! and yes I know I'm not helping either

tuzzio · 06-27-2016, 08:55 AM

Quote:

Originally Posted by CamryOnBronze

But if you had a couple of Porches to play with, would you want to work on this?

Yeah cause either way i can't afford even shitty porsche parts haha.

Pblesh85 · 06-28-2016, 10:09 AM

Quote:

Originally Posted by CamryOnBronze

He still has it. Plugging away as life allows if I am not mistaken. But if you had a couple of Porches to play with, would you want to work on this? lol

Me personally ? Yes I would... But that's me. (Keep in mind I LOVE Porsche)
But there is a certain satisfaction you get from a fun well rounded, hell even a rough(not shit box or fanboi car) s chassis. Not a lot of other cars offer that level of unrefined pleasure as an 240/sil-what have you.

Either way, people need to finish what they start. Or don't post in the first place. If you start a nice build, finish it. Don't get everyone's hopes up.

Anyway end of rant.... Update thread please.

06-27-2015, 02:17 AM	#751
heiyuu Zilvia Addict Join Date: Jun 2007 Location: winnipeg Age: 35 Posts: 875 Trader Rating: (6) Feedback Score: 6 reviews	May I ask what kinda floor sealer did you use on the garage and where u got it from? __________________

07-16-2015, 12:15 AM	#752
kuruptR Zilvia FREAK! Join Date: Jan 2003 Location: UpNorth Posts: 1,046 Trader Rating: (1) Feedback Score: 1 reviews	Weight Reduction and Chassis Prep Phase 1 I cut out the holes and dimpled them leaving the swiss cheesed sheet metal rigid. One hole aint do much, but many of them...still not much. Im pinching for lbs so everything will count in the end. I dimpled and drilled out a 1 1/2" hole, using a bolt driven die. Brackets, reinforcement plates, and other miscellaneous bracing have been drilled out with a spot weld drill bit (not pictured). I drilled through to the outside several times, I will have to go back weld in what holes I made. Once everything has been removed, I have began to remove all sound deadening, adhesives, and paint and primers. A heat gun was used for the deadening that was stubborn, and finished off with acetone and a lot of old microfiber cloths. I started a small section with aircraft paint stripper, with all the crevices it was difficult to scrape off. Also, it was not effective at going through the layers of paint. The car was originally red then painted black, so thats 2 coats of primer and 2 of paint. I noticed the aircraft stripper was not strong enough to penetrate through the primers. I switched the method to mechanical, scotch brite pads have been effective in the past but on a larger scale, using the large pads on an angle grinder. I used only 4 pads to get it to the stage pictured above, 4 pads @ $5.00 each. Left a very clean and smooth finish without warping or damaging the metal, I will finish the the rest with brush on aircraft stripper. Factory gas tank removal, theres a little fuel remaining so for safety I have removed it. The spare tire well will not be needed, It will give me a better view on how I want to mount the new fuel tank. I will be rolling out a new trunk pan, but it will come after planning the fuel system and wing layout. When Im finished this prep I will either begin to prep the cage for welding or Ill do the fuel system. I need to pickup a few things, a bead roller to do the floors, a tube notcher to notch the tubing for the cage and the fuel stuff. __________________ @woooster on instagram

07-16-2015, 05:14 AM	#753
turbo2nr Post Whore! Join Date: Jan 2005 Location: queens NYC Age: 35 Posts: 2,560 Trader Rating: (8) Feedback Score: 8 reviews	WOW amazing stuff. +1 for privateers! I cant wait to see the next steps. Plan on removing the drive' side hump on the floor so you can mount your seat better? Keep it up man! __________________ s14 kouki ka-t

08-04-2015, 08:04 AM	#755
CamryOnBronze Post Whore! Join Date: Oct 2008 Location: MI Age: 35 Posts: 3,913 Trader Rating: (131) Rides Gallery: CamryOnBronze Feedback Score: 131 reviews	Looking good! __________________ CamryOnBronze.com

10-21-2015, 06:59 PM	#756
dizzariot Post Whore! Join Date: May 2010 Location: Japan Posts: 5,127 Trader Rating: (47) Feedback Score: 47 reviews	Sub'd. So happy this is back in my life. __________________ *The mark of a true sucka: 'RARE JDM' & 'OLD LOGO NISMO'*

08-03-2015, 07:53 PM	#754
skun Join Date: May 2012 Location: Spain Age: 40 Posts: 2 Trader Rating: (0) Feedback Score: 0 reviews	Following this thread since you started it and every year this project goes better!! One question about SSR´s, the sizes you have was 18x9 +8, 18x10 +8 but they was specially ordered for you under your sizes specifications or maybe you used spacers? Coz I can not find this sizes at SSR website Thanks!!!

12-12-2015, 12:25 PM	#757
tacotacotaco Premium Member Join Date: Jun 2005 Location: GRRRVINE!!! Age: 38 Posts: 3,247 Trader Rating: (16) Rides Gallery: tacotacotaco Feedback Score: 16 reviews	Any New updates?

01-17-2016, 12:26 PM	#759
lilcim Zilvia Member Join Date: Nov 2012 Location: Montreal, Qc Age: 29 Posts: 292 Trader Rating: (2) Feedback Score: 2 reviews	I need to drive down from Quebec to see and hang S13 pals. OMG can't wait to see the next version of it. __________________ IG: @cimonbrouillette www.LowLevelStore.com

06-26-2016, 11:38 AM	#760
Pblesh85 Nissanaholic! Join Date: Sep 2005 Location: Tacoma wa Age: 36 Posts: 1,897 Trader Rating: (48) Feedback Score: 48 reviews	I am curious to see how this is progressing or if it was parted/sold like the rest of the interesting builds on here. __________________ Do you suffer from vaginal dryness...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode