SR20DET crankcase ventilation fitting - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Nikzilla · 07-17-2014, 08:46 PM

So I'm getting a catch can, and I want to convert all my ventilation lines to AN braided hose so that they don't burn up.

From what I read, you can just pull the valve cover Tee out (it's an s13 blacktop) and run a 3/8 NPT tap through it.

But what about the hose that goes into the block? If I remember correctly from when I did my rebuild, it's a nipple fitting pipe, that goes into the block underneath the head. You can't remove it without taking the head off. Also, tapping it would be extremely risky since it's a channel in the block that goes down to the oil pan. If I tapped it I would have to separate the head, block, and oil pans.

I've seen pictures before with people running an AN hose to down there behind the manifold, but I never could figure out how they did it.

What about cutting the nipple off the fitting, flaring it, and using a flare fitting?

Nikzilla · 07-17-2014, 08:56 PM

This is the fitting I am talking about btw.

Nikzilla · 07-18-2014, 01:18 PM

Sigh. Doed anyone at least know what size the hose is?

ultimateirving · 07-18-2014, 01:59 PM

Weld on a fitting ?

Nikzilla · 07-18-2014, 02:17 PM

Can I do that without splitting it?

ultimateirving · 07-18-2014, 02:37 PM

Quote:

Originally Posted by Nikzilla

Can I do that without splitting it?

I haven't tried but I thought that was what people did to convert it. Depends on if you can get a welder in that area. Is the engine in the car still ?

Nikzilla · 07-18-2014, 02:38 PM

Yeah but I'm gunna be pulling it soon to swap my tranny. I can't weld yet. I outsource my welding to a local machinist.

5t341tH · 01-25-2021, 08:35 PM

hey wanted to bump this up. So what are people doing at this piece? I have a AN fitting on the valve cover side and the other end just slips over the pipe. Just wanted to see if there's a nicer solution

EDIT: I see these pieces available but they require removing the head to install

240boosted · 05-29-2021, 08:58 PM

I getting my car setup and I using the Mazworx part and let me tell you I love it

07-17-2014, 08:46 PM	#1
Nikzilla Zilvia Member Join Date: Jun 2013 Location: Los Angeles Age: 26 Posts: 291 Trader Rating: (0) Feedback Score: 0 reviews	SR20DET crankcase ventilation fitting So I'm getting a catch can, and I want to convert all my ventilation lines to AN braided hose so that they don't burn up. From what I read, you can just pull the valve cover Tee out (it's an s13 blacktop) and run a 3/8 NPT tap through it. But what about the hose that goes into the block? If I remember correctly from when I did my rebuild, it's a nipple fitting pipe, that goes into the block underneath the head. You can't remove it without taking the head off. Also, tapping it would be extremely risky since it's a channel in the block that goes down to the oil pan. If I tapped it I would have to separate the head, block, and oil pans. I've seen pictures before with people running an AN hose to down there behind the manifold, but I never could figure out how they did it. What about cutting the nipple off the fitting, flaring it, and using a flare fitting?

07-18-2014, 01:59 PM	#4
ultimateirving Zilvia FREAK! Join Date: Nov 2010 Location: arizona Age: 33 Posts: 1,519 Trader Rating: (1) Feedback Score: 1 reviews	Weld on a fitting ? __________________ Z32 with lq4 swap Desert Street Scene \|\| Dssevents.com

01-25-2021, 08:35 PM	#8
5t341tH Post Whore! Join Date: Jun 2006 Location: socal (Huntington Beach) Age: 33 Posts: 2,776 Trader Rating: (14) Feedback Score: 14 reviews	hey wanted to bump this up. So what are people doing at this piece? I have a AN fitting on the valve cover side and the other end just slips over the pipe. Just wanted to see if there's a nicer solution EDIT: I see these pieces available but they require removing the head to install __________________ lexus baby

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-17-2014, 08:56 PM	#2
Nikzilla Zilvia Member Join Date: Jun 2013 Location: Los Angeles Age: 26 Posts: 291 Trader Rating: (0) Feedback Score: 0 reviews	This is the fitting I am talking about btw.

07-18-2014, 01:18 PM	#3
Nikzilla Zilvia Member Join Date: Jun 2013 Location: Los Angeles Age: 26 Posts: 291 Trader Rating: (0) Feedback Score: 0 reviews	Sigh. Doed anyone at least know what size the hose is?

07-18-2014, 02:17 PM	#5
Nikzilla Zilvia Member Join Date: Jun 2013 Location: Los Angeles Age: 26 Posts: 291 Trader Rating: (0) Feedback Score: 0 reviews	Can I do that without splitting it?

07-18-2014, 02:38 PM	#7
Nikzilla Zilvia Member Join Date: Jun 2013 Location: Los Angeles Age: 26 Posts: 291 Trader Rating: (0) Feedback Score: 0 reviews	Yeah but I'm gunna be pulling it soon to swap my tranny. I can't weld yet. I outsource my welding to a local machinist.

05-29-2021, 08:58 PM	#9
240boosted Leaky Injector Join Date: Nov 2010 Location: NYC Age: 31 Posts: 146 Trader Rating: (2) Feedback Score: 2 reviews	I getting my car setup and I using the Mazworx part and let me tell you I love it