How to assemble -AN lines *Approved* - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

tknbkthrsdy4anfg · 06-05-2007, 09:02 PM

Hey guys I decided to run a remote mount oil filter on my SR20 when I drop it in.

So here is how I made the lines

I got four -8AN hose ends, two 1/2” pipe to -8AN adapters, 3’ of -8AN braided stainless hose and an oil filter block.
First I cut the 3 feet of stainless hose in half by taping it with electrical tape and cutting it with the cutoff wheel.

Then I stripped off the electrical tape and slid the hose into the red part of the hose end, putting the end of the hose flush with the threads.

Then I lubricated the blue part of the hose end with some white lithium grease.

Next I clamped the red part into the vice using an AN assembly clamp and pushed the blue part of the AN fitting into the red.

I twisted it with my palm until the threads engaged then used a 7/8” AN wrench to tighten them.

I tightened the fitting until the red and blue parts were just about 1mm apart.

and viola you're done. I would advise however to blow some high pressure air thru the lines to get out any crap from cutting them. Also it hides the coolness but shrink wrapping the lines prevents them from fraying.

yokotas13 · 06-05-2007, 09:13 PM

nice write up
but people done nkow how to do that?

tknbkthrsdy4anfg · 06-05-2007, 09:15 PM

I dont know, noobs dont. I thought thats what this was all about.

Slidin240Wayz · 06-05-2007, 09:32 PM

I like this write up. I have only seen the other type of installer that holds the blue part and you push the hose into it.

Carlos

tknbkthrsdy4anfg · 06-06-2007, 12:13 AM

Thanks its from JEGS

'90RPS13 · 06-06-2007, 12:32 AM

How much did they run you? Also, what is to prevent the hose from falling out? Newb question, I know.

tknbkthrsdy4anfg · 06-06-2007, 08:58 AM

The line was about 15 dollars I think, the hose ends were about 8 bucks a piece and the adapters were about 8 bucks a piece.
Well whats holding the hose in, the blue part is male and the tip of it sandwiches the hose with the red part, there is also a barb if you look really close.

***FaLKoN240*** · 06-06-2007, 09:37 AM

I didn't know how to do that.

+ rep.

tknbkthrsdy4anfg · 06-06-2007, 10:11 AM

Thank you guys, I was a little afraid to do it too. Let me get a chance and I will post up how to do smaller -AN lines that require a ferrule.

Slidin240Wayz · 06-06-2007, 10:50 AM

Link to the assembly kits:

http://www.jegs.com/webapp/wcs/store...Term=koul+tool

tknbkthrsdy4anfg · 06-06-2007, 10:58 AM

Yea this one is good http://www.jegs.com/webapp/wcs/store...0002_537697_-1
however I think its better to cut off the line with a cut off wheel then with a pinch cutter, that way the hose says relatively round.

tknbkthrsdy4anfg · 06-13-2007, 10:25 AM

Is this worth posting in the public forum?

tknbkthrsdy4anfg · 06-19-2007, 11:11 AM

Mods... Kev? Phlip? Barry? anyone?

420sx · 06-19-2007, 03:53 PM

should have done an oil cooler with thermo like mine

tknbkthrsdy4anfg · 06-19-2007, 04:00 PM

I'm lookin at that right now, however it would have added substantially to the cost.

A Spec Products · 06-19-2007, 05:32 PM

Cool stuff

I just had Baker assemble the fittings for me

Figure I'd leave it to da pros

tknbkthrsdy4anfg · 06-19-2007, 05:47 PM

Lol, you would have the cash to do that logan.

fromxtor · 06-19-2007, 05:54 PM

Part of my job is assembling low/med/high pressure rubber and teflon(steel braided) hoses. from -3AN on up.

**mrmephistopheles** · 08-24-2007, 11:01 PM

06-05-2007, 09:13 PM	#2
yokotas13 Post Whore! Join Date: Apr 2006 Location: Milford, CT Age: 36 Posts: 10,519 Trader Rating: (8) Rides Gallery: yokotas13 Feedback Score: 8 reviews	nice write up but people done nkow how to do that? __________________ 2015 Subaru Outback Overlander - Wagonofdoom

06-05-2007, 09:32 PM	#4
Slidin240Wayz Post Whore! Join Date: Jan 2005 Location: Everywhere Age: 36 Posts: 5,427 Trader Rating: (9) Feedback Score: 9 reviews	I like this write up. I have only seen the other type of installer that holds the blue part and you push the hose into it. Carlos __________________ Support Zilvia by purchasing a sticker!

06-06-2007, 09:37 AM	#8
*FaLKoN240* Super Moderator Join Date: Jun 2004 Location: SF Bay Area Posts: 16,760 Trader Rating: (73) Feedback Score: 73 reviews	I didn't know how to do that. + rep. __________________ Best way to do business with me? Make your best offer FIRST.

06-06-2007, 10:50 AM	#10
Slidin240Wayz Post Whore! Join Date: Jan 2005 Location: Everywhere Age: 36 Posts: 5,427 Trader Rating: (9) Feedback Score: 9 reviews	Link to the assembly kits: http://www.jegs.com/webapp/wcs/store...Term=koul+tool __________________ Support Zilvia by purchasing a sticker!

06-19-2007, 03:53 PM	#14
420sx Post Whore! Join Date: Jun 2004 Location: Texas Age: 38 Posts: 3,960 Trader Rating: (0) Rides Gallery: 420sx Feedback Score: 0 reviews	should have done an oil cooler with thermo like mine __________________ hydropgrahics! ls1......

06-06-2007, 12:32 AM	#6
'90RPS13 BANNED Join Date: Jan 2006 Location: NC Age: 34 Posts: 2,839 Trader Rating: (0) Feedback Score: 0 reviews	How much did they run you? Also, what is to prevent the hose from falling out? Newb question, I know.

06-19-2007, 05:32 PM	#16
A Spec Products Post Whore! Join Date: Mar 2005 Location: Socal! Off 60/605 Posts: 7,256 Trader Rating: (27) Feedback Score: 27 reviews	Cool stuff I just had Baker assemble the fittings for me Figure I'd leave it to da pros __________________ A SPEC PRODUCTS CORP AME Wheels, Advan, ARC, Gram Lights, Nardi, Personal, Recaro, Works Bell, Work Wheels, Volk Racing, 5Zigen, & more! 626.618.1100 x 103 / aim: aspectuan Advertiser's Specials! Read / Give Feedback! Please Rate Us!

06-19-2007, 05:54 PM	#18
fromxtor Post Whore! Join Date: Aug 2005 Location: NC Age: 40 Posts: 3,012 Trader Rating: (23) Feedback Score: 23 reviews	Part of my job is assembling low/med/high pressure rubber and teflon(steel braided) hoses. from -3AN on up. __________________ Seller feedback>>http://www.zilvia.net/f/showthread.p...light=fromxtor

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode