Testing Waters: Parting out 400hp car LOTS of part

[GeoAtTitan]

If I can get buyers for a lot of these parts I will go ahead and part the car out. This setup made 386whp on just 20psi and 110 octane because I was out of injector. The car ran great other than needing tension rods so would make some clunking noises since the bushings where so worn out. The turbo looks laggy on the dyno sheet because it had a severe pre turbo exhaust leak that was later fixed.

Email [email protected] or call 407-758-1200.

All pictures here http://photobucket.com/albums/a210/GeoAtTitan/S13/

Will be slowly adding them as I take shiat off.

Chassis

124k miles
White
Overall not bad condition. Check pics.
Newer Tokiko blues
H&R Springs
Steelies
Pioneer CD Player with unknown not blown speakers
Leather seats (have rips, could use some S14 Seats)
It is stripped from the front seats back.
Dash only has one crack.
No motor, no tranny.
Have not decided if it will come with SR20DET Harness yet
Tension rods need to be replaced
$700

17" Racing Hart Knock offs(check pics) with good tires $450

2 15" Stock wheels on Mickey Thompson Drag Radials Less than 100 miles on these 235/60/15 $300

Cusco front and rear strut bars $125 *pending sale*

HKS 264 Step 1 Cams $300 *pending sale*

Greddy knock off Intake Manifold Semi Polished. Perfect condition. Has been pressure tested to over 30psi. $225 *pending sale*

Megan Racing Header
Megan Racing O2 housing
GT25R .86 a/r Dual Ball Bearing Turbo
HKS Actuator
All braided oil and water lines.
Custom aluminum 4" Intake with couplers and filter. Basically this is a complete bolt on turbo setup that will make 400+hp no problem.
Full setup in perfect working condition. $1050 *sold*

3" Downpipe
3" Test Pipe
Apexi N1 Cat Back
All for $400

Z32 Maf with plug $100 *sold*

2.5" Hot Pipe setup right now for a GT25R.
HKS SSQV
Greddy FMIC 24V
All couplers and clamps
Greddy Cold Pipe
$700 *pending sale*

Upgraded 550CC Injectors $325 *sold*

Walbro 255HP Fuel Pump rewired $75 *sold*

Yellow Top Optima Batter relocated correctly to the back $50 *sold*

Enthalpy Tuned ECU for the setup above (gt25r/550s/z32/264s/intake manifold) $350 *pending sale*

Greddy Profec B Spec 2 literally has less than 5 miles $275 *sold*

Greddy Remote switch $75 or $50 when bought with spec 2 *pending sale*

Clutchmasters Stage 4 Clutch (has less than 100 miles) Awesome clutch. Very light pedal but has great holding capacity. It is a 4 puck sprung. $385

Auto Meter Phantom Boost Gauge 30psi $35 *pending sale*

Auto Meter Phantom Oil pressure gauge $35

Auto Meter Phantom EGT Gauge no sensor $50

Greddy FATT Turbo Timer $50 *sold*

SR20DET Ignitor $85

Cam Angle Sensor $85

SR20DET Tranny. Shifts PERFECT $200 *pending sale*

SR20DET Tranny bad 5th/reverse $75

SR20DET blacktop shortblock. Had perfect compression till my car dropped a valve so it probably has 1 damaged piston Would be perfect for a buildup $200 *pending sale*

SR20DET Blacktop Head Was perfect, never smoked or anything but dropped a valve do to over revving it $200 *pending sale*

Blacktop Valve Cover $50

[sw20>>s14]

if the cusco strut bars are OS shaft and the price is for both, i got dibs and ill pay all the shipping you want baby...

edit: oh yeah, you might wanna add if the parts are for s13 or s14

[MI SO FST]

send me pics of the FMIC with the cold pipe. I could be interested in that if the condition is good. How many Miles?

EDIT. just saw pics on your link. I am interested in the FMIC as long as its a RSPL and NOT the VSPL and the Intake manifold. Give me a good price. PM me with info and price shipped to Chicago 60618.

[sw20>>s14]

okay, nvm...just noticed that you had pics of your s13...ill still take the front...how much shipped to CA, 94403?

[eyustfu]

willing to ship the block/head and maybe the tranny too? if so how much to 75040?

[GeoAtTitan]

I will have to look into the shipping for the block/head/tranny but yes I can do that no problem through work. Will just take a couple days and have to make sure it is packaged right. Probably can put them all together on a pallet.

As far as the cusco yes they are the OS bars and price is for both. THey just need to be repolished as you can see in the pictures they are not real shiny anymore.

I made a mistake on the fmic setup it is the VSPL. It is still a good deal for all those parts. I won't separate them just yet. If anything changes I will let you guys know. As of right now I want to sell like this.

2.5" Hot Pipe setup right now for a GT25R.
HKS SSQV
Greddy FMIC 24R
All couplers and clamps
Greddy Cold Pipe
$700

[MI SO FST]

ok will since its the VSPL that price is too much for me. Let me know when you want to sell that Intake manifold.

[the head]

how many miles on the cams?

[GeoAtTitan]

ok will since its the VSPL that price is too much for me. Let me know when you want to sell that Intake manifold.

How is that? The intercooler by itself without hot pipe and BOV sells for $700.

The cams have less than 300 miles. Installed a month ago or so. Where bought brand new. However the cams are spoken for already.

[MI SO FST]

How is that? The intercooler by itself without hot pipe and BOV sells for $700.



you got PM

OH BTW, you should change your post on the FMIC to a 24V not a 24R

[GeoAtTitan]

Done thanks.

[quach]

are the strut bars still available? if so how much would you want for them shipped to CA 94606? i understand that sw20>>s14 wants the front, but if you would rather sell as a set, i might be interested in buying both.

[KA-T_240]

will take z32 maf

[GeoAtTitan]

will take z32 maf

z32 maf sold tonight as well as strut bars.

[WILDACEX187]

will u part the oil and coolant turbo lines?

[GeoAtTitan]

No unfortunately not.

[jc_rps13]

mafs gone??? If not want the fuel pump and mafs...

[GeoAtTitan]

Maf is gone. Pump still available.