PDA

View Full Version : Fuel Pressure issue related to stalling?


xtahoex
09-18-2018, 11:00 AM
Hi everyone... Did some searching and could find anything definitive, so here it goes.

I have a Datsun with S15 SR20DET swapped. The ECU was tuned by Enthalpy and I have been working with them to solve this issue. But, I might be at a stalemate right now.

The issue I am having is the car is stalling on deceleration. Enthalpy has told me that my fuel pressure should never dip below 45 psi, under deceleration I am at 40 psi.

I am using a stock FPR. With vacuum disconnected it jumps to 51 psi, with vacuum connect it sit at 45 psi at idle. At 9lbs of boost I show 60 psi of fuel.

Bottom line Enthalpy tells me that fuel pressure should be set at 45 psi with the vacuum disconnected.

Could any of this be related to my stalling issues?

Thanks

5280VertDET
09-18-2018, 01:19 PM
There's a vac leak somewhere, built a vac leak tester. It's PITA to track down, but that what it sound like to me.

also,

See if you can test with known good FPR.

xtahoex
09-18-2018, 09:12 PM
I guess I should have added that I have done the following trying to chase down the problem...

New coolant temperature sensor
Verified that the Z32 MAF and TPS were within spec and that TPS was adjusted
Cleaned and adjusted IACV
Lengthened intake tube in between MAF and Turbo
New fuel pump and added Prosport electronic fuel pressure gauge
Completed boost and vacuum leak tests and repaired several leaks

Thats why I am down to either an issue with the FPR or a tuning issue? Can anyone think of anything else?

The car starts and idles like a champ, it accelerates good, it's only on deceleration with the clutch in is when fuel pressure drops to 40 PSI and the car stalls out.

Can anyone verify what their fuel pressure is in a similar situation under deceleration with clutch in?

Ryan

Datsun freak
09-19-2018, 08:27 AM
Bad blow off Valve unless you’re not running one now

xtahoex
09-19-2018, 08:54 AM
I removed the too. Running no BOV right now.

Datsun freak
09-19-2018, 09:01 AM
Now that I remember I had similar issue with my Jim wolf ecu , I was able to get rid of the stall at decel by changing settings in my safc , cant recall what settings I had to play with I just went off What I got from searching safc tuning , safc has air deceleration setting you can adjust to compensate enough to keep her in under decel


http://forums.nicoclub.com/afc-air-deceleration-setting-help-t312068.html

Datsun freak
09-19-2018, 09:06 AM
http://forums.nicoclub.com/afc-air-deceleration-setting-help-t312068.html

5280VertDET
09-19-2018, 09:30 AM
Which ECU do you have?

xtahoex
09-19-2018, 11:15 AM
Stock S15 ECU tuned by Enthalpy.

Datsun freak
09-19-2018, 11:30 AM
Get an afc and adjust air decrease settings


Search safc air deceleration settings on google

5280VertDET
09-19-2018, 11:48 AM
Stock S15 ECU tuned by Enthalpy.

Yea, thanks, I mean what is the code of the ECU?

If it's an auto ECU deceleration is different.

xtahoex
09-19-2018, 11:54 AM
It's a 6 speed ECU... I don't have the code for it right now.

Enthalpy is going to send me a new ROM. Hopefully they can make the adjustments to the tables because I don't want to run piggyback.

Datsun freak
09-19-2018, 12:37 PM
It's a 6 speed ECU... I don't have the code for it right now.

Enthalpy is going to send me a new ROM. Hopefully they can make the adjustments to the tables because I don't want to run piggyback.

How long has the tune turn around been from enthalpy? I might have to get one sounds like you get pretty fast turn around

xtahoex
09-19-2018, 01:19 PM
How long has the tune turn around been from enthalpy? I might have to get one sounds like you get pretty fast turn around

The turn around was good. About a week and I live in California and they are in Florida. I decided on enthalpy vs a piggyback and although there have been a few issues (most of them are on my end) Martin has been very helpful and is reachable by phone or email.

Are you currently driving in a Datsun? If so, what type?

Datsun freak
09-19-2018, 01:28 PM
The turn around was good. About a week and I live in California and they are in Florida. I decided on enthalpy vs a piggyback and although there have been a few issues (most of them are on my end) Martin has been very helpful and is reachable by phone or email.

Are you currently driving in a Datsun? If so, what type?


I’m running a 67 1600 with a KAT setup , I’m on a Jim wolf ecu now but have been waiting about 3 weeks for them to send me back my distributor for a reclock .

I’m looking for other ways to get it done now I have a feeling something is wrong . I went on the enthalpy site I’ll give him a call and get a tune from him.

I bet if I order a tune today it’ll get here before Jim wolfs reclocked distributor does .

xtahoex
09-20-2018, 12:54 PM
I’m running a 67 1600 with a KAT setup , I’m on a Jim wolf ecu now but have been waiting about 3 weeks for them to send me back my distributor for a reclock .

I’m looking for other ways to get it done now I have a feeling something is wrong . I went on the enthalpy site I’ll give him a call and get a tune from him.

I bet if I order a tune today it’ll get here before Jim wolfs reclocked distributor does .

Very cool. I'm running a 71 Datsun 1200 Sedan with a 510 independent rear swap.

Kingtal0n
09-20-2018, 04:28 PM
1. pressure test
2. Run a Recirculated Bypass

fixed

gota watch the wideband to see where it goes when you lift for diagnosis. Chances are that air is moving backwards through the compressor and interfering with the maf signal.
It isn't common on sr20 because the manual trans ecu have a fuel cut when TPS goes to 0%. So maybe your tps is not adjusted correctly for this.

Like someone said, SAFC has a minimum decel air function that people can use on MAF cars to limit max airflow during low throttle percentage%.

The question is, is this the cause of your symptom, and why. It could be plumbing related, turbo related, (maf tube) etc... Or it could be something else of course we can't see from here.That is why wideband diag is necessary.