silviaNC
02-22-2016, 11:25 AM
Gauging interest on my car.
Made 611 @19 psi on pump gas
Dyno video
17k$$
https://m.facebook.com/story.php?story_fbid=773329676088103&id=142284982525912&_rdr
Block:
Balanced bottom end, ACL bearings, micropolished crank with raw brokerage crank collar
N1 oil pump with spool billet gears
Metal jacket crank damper
9.5 qt oil sump
Eagle rods
Je 87mm pistons 8:3:1
Arp main and head studs
Oil restrictor
Z32 tranny
JWT 750tq clutch kit and lightweight flywheel
1 piece steel driveshaft
Q45 rear end swap with 3.91 gears
Head:
Apexi HG
Super tech valves, guides,springs,retainers
Tomei type B cams
Valve job
Greddy Timing belt
Head oil drain
Intake:
Stock intake and itbs.
Precision 750 hp intercooler with 2.5 hot side ,3" intake side
AEM intake filter
Fuel:
Aeromotive fpr
All an fittings from tank to fuel rail
Dual walbro 255
Flex fuel sensor(not wired)
ID 1000cc injectors on dual feed fuel rail setup
Exhaust :
Raw brokerage t4 twin scroll manifold
Dual tial 38mm wg with dump pipes
Raw brokerage 3" down pipe
Precision 6262 bb twin scroll turbo with .84 rear housing.
Electronics:
Haltech plug in Ecu
Wiring specialties custom harness
3bar map sensor and haltech AIT
Aem boost and AFR digital gauges
Pros port oil fuel pressure and water temp gauges.
Haltech boost controller
Aem water meth injection kit(installed but not used)
Custom monitor display
Suspension:
Stance pro coilovers, Megan tension rods and rucas.
Sikky front swaybar and suspension techniques rear swaybar.
Z32 brake swap with z33 rotors
Wheels :
Work VS-xx
17x11/ 17x9.5 with toyo T1 front /Toyo TQ drag radials in back
Cooling:Custom Tucked radiator and shroud with Derale 2200cfm single fan
Greddy oil thermostat and 7 row oil cooler
R32 front seats.
I'm sure I missing some stuff.
Compression 123/125 across
Leak down 10% cyl 2-5 13% cyl 1
Piston ring gap was built loose and smoke a lil on decel until you out some heat on.
http://uploads.tapatalk-cdn.com/20160222/ded673e49c1d8900f4dfd5644676216a.jpghttp://uploads.tapatalk-cdn.com/20160222/6f3d1512ad22bbdc8ce4092621aca880.jpghttp://uploads.tapatalk-cdn.com/20160222/5d418c28cab3bb21c31c85edde275259.jpghttp://uploads.tapatalk-cdn.com/20160222/f6d5a9dd10e6818a00b24d8706c25c21.jpghttp://uploads.tapatalk-cdn.com/20160222/3773b9715c580862f5a15fa8205578af.jpghttp://uploads.tapatalk-cdn.com/20160222/74ce9f90e5c6374178bd42d93fe4be0b.jpghttp://uploads.tapatalk-cdn.com/20160222/8ecbeebc8d646710d410133e244d0f1f.jpghttp://uploads.tapatalk-cdn.com/20160222/28b861d0b8a8a3fb1caeb12c215ccff9.jpg
Sent from my iPhone using Tapatalk
Made 611 @19 psi on pump gas
Dyno video
17k$$
https://m.facebook.com/story.php?story_fbid=773329676088103&id=142284982525912&_rdr
Block:
Balanced bottom end, ACL bearings, micropolished crank with raw brokerage crank collar
N1 oil pump with spool billet gears
Metal jacket crank damper
9.5 qt oil sump
Eagle rods
Je 87mm pistons 8:3:1
Arp main and head studs
Oil restrictor
Z32 tranny
JWT 750tq clutch kit and lightweight flywheel
1 piece steel driveshaft
Q45 rear end swap with 3.91 gears
Head:
Apexi HG
Super tech valves, guides,springs,retainers
Tomei type B cams
Valve job
Greddy Timing belt
Head oil drain
Intake:
Stock intake and itbs.
Precision 750 hp intercooler with 2.5 hot side ,3" intake side
AEM intake filter
Fuel:
Aeromotive fpr
All an fittings from tank to fuel rail
Dual walbro 255
Flex fuel sensor(not wired)
ID 1000cc injectors on dual feed fuel rail setup
Exhaust :
Raw brokerage t4 twin scroll manifold
Dual tial 38mm wg with dump pipes
Raw brokerage 3" down pipe
Precision 6262 bb twin scroll turbo with .84 rear housing.
Electronics:
Haltech plug in Ecu
Wiring specialties custom harness
3bar map sensor and haltech AIT
Aem boost and AFR digital gauges
Pros port oil fuel pressure and water temp gauges.
Haltech boost controller
Aem water meth injection kit(installed but not used)
Custom monitor display
Suspension:
Stance pro coilovers, Megan tension rods and rucas.
Sikky front swaybar and suspension techniques rear swaybar.
Z32 brake swap with z33 rotors
Wheels :
Work VS-xx
17x11/ 17x9.5 with toyo T1 front /Toyo TQ drag radials in back
Cooling:Custom Tucked radiator and shroud with Derale 2200cfm single fan
Greddy oil thermostat and 7 row oil cooler
R32 front seats.
I'm sure I missing some stuff.
Compression 123/125 across
Leak down 10% cyl 2-5 13% cyl 1
Piston ring gap was built loose and smoke a lil on decel until you out some heat on.
http://uploads.tapatalk-cdn.com/20160222/ded673e49c1d8900f4dfd5644676216a.jpghttp://uploads.tapatalk-cdn.com/20160222/6f3d1512ad22bbdc8ce4092621aca880.jpghttp://uploads.tapatalk-cdn.com/20160222/5d418c28cab3bb21c31c85edde275259.jpghttp://uploads.tapatalk-cdn.com/20160222/f6d5a9dd10e6818a00b24d8706c25c21.jpghttp://uploads.tapatalk-cdn.com/20160222/3773b9715c580862f5a15fa8205578af.jpghttp://uploads.tapatalk-cdn.com/20160222/74ce9f90e5c6374178bd42d93fe4be0b.jpghttp://uploads.tapatalk-cdn.com/20160222/8ecbeebc8d646710d410133e244d0f1f.jpghttp://uploads.tapatalk-cdn.com/20160222/28b861d0b8a8a3fb1caeb12c215ccff9.jpg
Sent from my iPhone using Tapatalk