supersayianjim
03-23-2013, 10:54 AM
so iam in a bit of a rut people. previously i installed the consult plug for my rb20det. it was a breeze of an install and it did what is was supposted to do. now apparently it's not so easy and the damn computer won't connect with the nistune ecu.
so iam hoping you guys can help me out here.
heres the diagram i used for my previous install. it's from the fsm. and apparently it dosen't have the rb25det pinout
(just the de-non turbo one).
so one has to assume that the 20-25 are the same right??
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rb20ecupinout_zps6787be5c.jpg
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/pinout2_zps12e2346c.jpg
whats weird is on the diagram pin 55 has no use. but on my actuall harness power goes there??? so i got that for my 12v source.
heres my tx splice.
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/txwiring_zps9cdf16d6.jpg
and heres my rx splice
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rxwiring_zpseb66abc5.jpg
and my clk splice
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/clkwiring_zps7260e5ce.jpg
for the guys who are more visiual. my splices are as follows.
tx=red wire. with white stripe
rx=yellow wire with red stripe
clk=brown wire,yellow strips
12v=55 pin.
so when i try to connect the nistune to my ecu i get a momentarly blink from the rx light. but no connection
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rxblinksfirst_zpsd2e3706f.jpg
so guys do i have this wired wrong?? is the rb25 pinout plug funky, or am i just screwed???
i updated the drivers on my laptop(apparently).
HELP GUYS!!!
so iam hoping you guys can help me out here.
heres the diagram i used for my previous install. it's from the fsm. and apparently it dosen't have the rb25det pinout
(just the de-non turbo one).
so one has to assume that the 20-25 are the same right??
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rb20ecupinout_zps6787be5c.jpg
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/pinout2_zps12e2346c.jpg
whats weird is on the diagram pin 55 has no use. but on my actuall harness power goes there??? so i got that for my 12v source.
heres my tx splice.
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/txwiring_zps9cdf16d6.jpg
and heres my rx splice
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rxwiring_zpseb66abc5.jpg
and my clk splice
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/clkwiring_zps7260e5ce.jpg
for the guys who are more visiual. my splices are as follows.
tx=red wire. with white stripe
rx=yellow wire with red stripe
clk=brown wire,yellow strips
12v=55 pin.
so when i try to connect the nistune to my ecu i get a momentarly blink from the rx light. but no connection
http://i1062.photobucket.com/albums/t493/supersayianjim2/project%20s-rb%202/rxblinksfirst_zpsd2e3706f.jpg
so guys do i have this wired wrong?? is the rb25 pinout plug funky, or am i just screwed???
i updated the drivers on my laptop(apparently).
HELP GUYS!!!