swap my engine

[nissanduster]

i'm going to sway my ka24e to a sr20det BT. What parts do i need and should change in my engine bay. just need alittle bit more help. thanks

[89JDM240sx]

Google Sr20 swap kits you'll get everything you need... Just remember to upgrade to a Z32 fuel filter and 255lph fuel pump

[nissanduster]

ok thanks and do i have to change my driveshaft. haha

[89JDM240sx]

No Sir you don't.. Aluminum 1pc wouldn't hurt though... Lol

[nissanduster]

ok thanks. so the basic's i would need is intercooler, piping, wiring harness (could do it myself), gauges, change my throttle cable to a s14, and if and anything else please let me know.

[89JDM240sx]

Bov, turbo timer, air filter

[onehundredoctane]

This thread makes me
http://1.bp.blogspot.com/_FZVvgFCIxXM/TD5qPdtzViI/AAAAAAAAABE/Ht-VwGQ6bjY/s1600/confused-full.jpg

[onehundredoctane]

and it wasn't from Florida? What ze hell?

[nissanduster]

VA all day

[gostrider]

ISIS Front Mount Intercooler Kit
-Walbro 255 Fuel Pump with Install Kit
-ISIS Dual 12" Electric Fans
-ISIS Stainless Steel Downpipe
-Samco Atmospheric BOV
-Small Interstate Battery
-Crossover Radiator Hose
-Conversion Heater Hose Set
-MAF Adaptor and New Filter
-NGK Spark Plugs
-All Fluids (oil, coolant, etc.)
-Welding of AC and BOV components
-MPI Fuel line and New OEM Fuel Filter
-AC Receiver Dryer
New Belts
-New OEM Water Pump
-FLex-a-Lite Dual #112 Electric Fans
-Replacement of ALL coolant hoses
-New OEM Thermostat
-Front and Rear Main Seals
-Transmission Seals and Gaskets
-Redline MT-90 Gear Oil
-Z32 Fuel Filter
-New OEM Exedy Clutch set
-Resurfaced Flywheel

that should be a good start..

[jdm213]

ISIS Front Mount Intercooler Kit
-Walbro 255 Fuel Pump with Install Kit
-ISIS Dual 12" Electric Fans
-ISIS Stainless Steel Downpipe
-Samco Atmospheric BOV
-Small Interstate Battery
-Crossover Radiator Hose
-Conversion Heater Hose Set
-MAF Adaptor and New Filter
-NGK Spark Plugs
-All Fluids (oil, coolant, etc.)
-Welding of AC and BOV components
-MPI Fuel line and New OEM Fuel Filter
-AC Receiver Dryer
New Belts
-New OEM Water Pump
-FLex-a-Lite Dual #112 Electric Fans
-Replacement of ALL coolant hoses
-New OEM Thermostat
-Front and Rear Main Seals
-Transmission Seals and Gaskets
-Redline MT-90 Gear Oil
-Z32 Fuel Filter
-New OEM Exedy Clutch set
-Resurfaced Flywheel

that should be a good start..


thicker mishi or koyo rad wouldnt hurt either :whip:

[nissanduster]

ok so this is on my parts list:

sr20det red top
koyo radiator
greddy intercooler (maybe) also comes with piping
AEM wideband gauge
AEM boost gauge
AEM oil press gauge
Walbro fuel pump 225
z32 fuel fitler
z32 MAF
s14 throttle cable

parts thinking about:
Dual eletric fans
BOV hks or greddy
lsd but dont know which one, thinking about kaaz
Aluminum 1pc driveshaft
Defi control unit

if i think of anything else i'll post it, if anything else i would like to know this is going to be my first import build. thanks

[nissanduster]

parts thinking about:
5 lug con

[mkezzo16]

Not being a dick, the people have been nice so far..but you may end up getting flamed by alot of people here just because this is a common swap. The advice thats been given so far is good except i would use a clutch fan opposed to e fans. The KAde and rb fan is alot better than the sr20 fan.

[KiLLeR2001]

ITT: noob spoon feeds the super noob on the most basic information that exists on Zilvia.

[Kingtal0n]

ok so this is on my parts list:

sr20det red top
z32 MAF
Dual eletric fans
hks or greddy
lsd
Aluminum 1pc driveshaft



1. save a little more money and get an S14 sr20det if possible
2. Do not use a Z32 maf unless you exceed the OEM maf capability
3. Use an OEM clutch fan and shroud
4. HKS if you do not want to recirculate, greddy type-s (authentic) if you intend to recirc.
5. I would use a typical VLSD if you daily drive
6. A one-piece driveshaft is a great upgrade for the drivetrain, but if you are involved in a specific car crash, the driveshaft may hurt you. A two-piece gives you a margin of safety.

[onehundredoctane]

ITT: noob spoon feeds the super noob on the most basic information that exists on Zilvia.

Rep'd +1

DDBS threads.

[Croustibat]

Not being a dick, the people have been nice so far..but you may end up getting flamed by alot of people here just because this is a common swap. The advice thats been given so far is good except i would use a clutch fan opposed to e fans. The KAde and rb fan is alot better than the sr20 fan.

It is not even a swap per se, the car exist as standard with that engine on every continent except america, and is called 200sx, not 240sx. He is just changing the car to what it is supposed to be :D

[cotbu]

It is not even a swap per se, the car exist as standard with that engine on every continent except america, and is called 200sx, not 240sx. He is just changing the car to what it is supposed to be :D

That's how I look at it, and the screwed up the steering wheel location, but I can live with that!
That's what we get for buying knockoffs!;)

[SLiDe_WaYz]

How did u not find anything in google.

Stock motor mounts work fine

Why would you buy a Defi control unit if your buying aem gauges that makes zero since.

Your stock fan shroud and fan won't work, you need e fans or a sr shroud with your ka clutch fan.

[nissanduster]

i did fine stuff on google just wanted to know more from other people.

I thougth you need something to hook up the gauges, but i dont know what it is.

and im probley going to get e fans becuse i dont like how the other fan looks on the engine.