NismoTuner21
12-14-2011, 10:13 PM
Decided to go a different route due to my harness not being setup well for and it and I don't feel like redoing the harness. This is the NEWEST version of Megasquirt out there. It can even tune itself if you have a wideband wired up!! I got this thing like a month ago, the MAP sensor is still in packaging! I can also include a 1JZ jumper harness for an extra $70. NEED TO SELL ASAP I WANNA DRIVE!
$625
561 319 1579
MegaSquirt-III Engine Management System w/PCB3.57 - Assembled Unit Part # MS3X357-C_BL
It's finally here! The MegaSquirt-III is a drop in daughter card that greatly expands the MegaSquirt's functionality.
We now have complete, ready to run MegaSquirt-III ECUs. This one includes the MS3X expansion board. 2.5 bar MAP sensor is standard equipment.
The MS3 daughter card on its own will give you all these features and more:
VE and ignition tables are now both 16 x 16
0.1% steps on VE table, 0.1 degree steps on ignition table
Socket for an onboard SD card - no laptop required for data logging (SD Card not included)
Built in USB port
GM stepper IAC control
Closed loop idle and mixture control
CANBus communications for interface with GPIO Board, IO Extender, or other devices
Staged injection
Native support for many different OEM trigger patterns
This MS3 EMS already has the MS3X expansion board installed, enabling the following features:
8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils and our IGN-1As. Requires external module or coils with internal ignitors.
6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (with external conditioner), and more.
1 Cam sensor input. Can be used with VR, Hall, or optical sensors.
The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio.
$625
561 319 1579
MegaSquirt-III Engine Management System w/PCB3.57 - Assembled Unit Part # MS3X357-C_BL
It's finally here! The MegaSquirt-III is a drop in daughter card that greatly expands the MegaSquirt's functionality.
We now have complete, ready to run MegaSquirt-III ECUs. This one includes the MS3X expansion board. 2.5 bar MAP sensor is standard equipment.
The MS3 daughter card on its own will give you all these features and more:
VE and ignition tables are now both 16 x 16
0.1% steps on VE table, 0.1 degree steps on ignition table
Socket for an onboard SD card - no laptop required for data logging (SD Card not included)
Built in USB port
GM stepper IAC control
Closed loop idle and mixture control
CANBus communications for interface with GPIO Board, IO Extender, or other devices
Staged injection
Native support for many different OEM trigger patterns
This MS3 EMS already has the MS3X expansion board installed, enabling the following features:
8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils and our IGN-1As. Requires external module or coils with internal ignitors.
6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (with external conditioner), and more.
1 Cam sensor input. Can be used with VR, Hall, or optical sensors.
The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio.