PDA

View Full Version : N1 rb26 failure


Sideways_blksr20
12-12-2011, 10:03 PM
I dont know what i did wrong , i replaced my 26 water pump with a brand new rb25 n1 water pump.. Started the car and its spraying coolant likecrazy..
I know rb25 pumps and 26's r the same.
Any help guys

memphis180sx
12-12-2011, 10:11 PM
Is it spraying out of the waterpump?

Sideways_blksr20
12-12-2011, 10:16 PM
Yeah ....

GRNxS14
12-12-2011, 10:23 PM
Not to insult your intelligence, but you did use gasket maker to seal it up correct? Where exactly is the water spraying out of?

Chrischeezer
12-12-2011, 10:36 PM
Yeah there's no oblong bolt hole in you block BUT that the upgraded N1 water pump has one, and it open to your cooling system. you'll have to weld it or seal it up.. its common

http://lh3.ggpht.com/_8MPCKJQzPA8/SVUlL9OKEjI/AAAAAAAAU8c/sM_XD8qh3FA/aae%5B10%5D.jpg

Sideways_blksr20
12-12-2011, 10:42 PM
Damn can i just weld it without taking it out it is coming right from there .

Sideways_blksr20
12-12-2011, 10:43 PM
Not to insult your intelligence, but you did use gasket maker to seal it up correct? Where exactly is the water spraying out of?

Yeah i did bro but ididnt know u were supposed to weld that hole ...

Chrischeezer
12-12-2011, 10:48 PM
I wouldn't do this but...

I have read that most ppl fill the whole with silicone as its a very small part not sealed.

read up on it,

Chrischeezer
12-12-2011, 10:52 PM
http://i991.photobucket.com/albums/af33/godzirra32/IphonePics217.jpg


its gross but it works

Sideways_blksr20
12-12-2011, 11:09 PM
So i dontneed to remove the whole pump ? Just fill the hole with rtv and put back the bolt with a washer ?

silver350z05rb
12-13-2011, 12:22 AM
yea its common like they said, i have heard of doing both, silicone the shit out of it or weld it as well, i would assume welding it shut would be better?correct? i mean im sure its about than $10 bucks for someone to weld that for you. or Free if you have a machine.

Sideways_blksr20
12-13-2011, 09:47 AM
So should i just remove the one bolt fill it up with rtv and put back the bolt with a washer?

mattack69
12-13-2011, 09:49 AM
Weld this, do it right the first time. Those aren't cheap if they fail.

Sideways_blksr20
12-13-2011, 09:56 AM
So weld it an redrill it ?

mattack69
12-13-2011, 10:24 AM
Have it welded then retap yes. That's my vote at least. Should be fairly easy :)

rbs14kouki
12-13-2011, 11:05 AM
i had 2 rb26 with N1 pump !!!! all my bolt were in place except for that one your talking about !!! put alot of RTV in the oval hole and insert bolt bolt with washer !!!

never leaked any coolant


i used the orange RTV that came in my rebuilt gasket kit !!!
http://i202.photobucket.com/albums/aa74/rbs14kouki/my%20240sx/SSPX0953.jpg
http://i202.photobucket.com/albums/aa74/rbs14kouki/my%20240sx/SSPX1039.jpg

rbs14kouki
12-13-2011, 11:20 AM
If you dont want to remove the pump ! Make sure you dry everything cause the Rtv wont stick good

Chrischeezer
12-13-2011, 12:19 PM
use "Ultra Gray" silicone too.. it dries much harder.

just bragging : my R34 engine doesn't have this problem

Sideways_blksr20
12-13-2011, 02:50 PM
Thank u guys