PDA

View Full Version : wtb - building a s13 blacktop sr need sr engine parts

drftx
10-04-2011, 10:49 PM
looking for

upgraded valve springs/retainers (bc/jun/hks/etc.)
Timing chain guide
Timing chain cover
arp headstuds/mains
all the bearings (thurst/main/etc.) preferably whole kit
oil pan bolts

or any other aftermarket parts for a sr build thx
TurboDaytona
10-05-2011, 08:09 AM
I have all the OEM oil pan bolts. Labeled, bagged and ready to go. $20 shipped?
JDS Performance
10-05-2011, 08:22 AM
looking for

upgraded valve springs/retainers (bc/jun/hks/etc.)
Timing chain guide
Timing chain cover
arp headstuds/mains
all the bearings (thurst/main/etc.) preferably whole kit
oil pan bolts

or any other aftermarket parts for a sr build thx

I think I talked to you already if not:
BC springs/Ti retainers - $175 shipped
ARP head stud (undercut) 1 torque cycle - $95.00 shipped
ARP new Mains with 2 rear serviced $140 shipped
Crankshaft kit (with bearings) $375 shipped
New oil pan bolt kit $17 shipped
LMK [email protected]
zz_kouki_zz
10-05-2011, 08:57 AM
I have the isis intake manifold, perfect for bigger horsepower if you wanna do that now or later. Looks good on sr engine, check my thread, that picture there was on my kouki :)

lemme know
brn2slid
10-05-2011, 10:37 AM
Brand new head/main studs, at just about the same price dude wants for his used ones (odd), cometic gasket, greddy rocker arm stoppers. Just recently bought a built head, will have to check as to what all was in it again, I'll get back to you on that
StReeTz
10-05-2011, 02:59 PM
Need injectors? or a fresh harness?
drftx
10-06-2011, 12:15 PM
Need injectors? or a fresh harness?

not right now just need these parts i need

Brand new head/main studs, at just about the same price dude wants for his used ones (odd), cometic gasket, greddy rocker arm stoppers. Just recently bought a built head, will have to check as to what all was in it again, I'll get back to you on that

whats the price on the cosmetic gasket and ras also inm looking for aftermarket springs/retainers

I have the isis intake manifold, perfect for bigger horsepower if you wanna do that now or later. Looks good on sr engine, check my thread, that picture there was on my kouki :)

lemme know

not right now just doing the internals

I think I talked to you already if not:
BC springs/Ti retainers - $175 shipped
ARP head stud (undercut) 1 torque cycle - $95.00 shipped
ARP new Mains with 2 rear serviced $140 shipped
Crankshaft kit (with bearings) $375 shipped
New oil pan bolt kit $17 shipped
LMK [email protected]

id love to pick up the bc springs/retainers but you dont accept paypal
KaminaSan
10-07-2011, 02:13 AM
Yo! I have A full set of brand new ACL race bearings for an Sr20det S13.

This is a full set of both Rod and Main bearings STD size.

ACL Race Main & Rod Bearings Set SR20DE SR20DET STD (http://www.frsport.com/ACL-Race-Main---Rod-Bearings-Set-SR20DE-SR20DET-STD_p_15960.html)
They sell for 115, I'm only asking 90, shipped.

Also have Sr20det 370cc injectors for 75

Sr20det t25 turbo for 105.

Not sure if you need any of the other stuff, but it's on the table.
brickerj
10-07-2011, 06:32 AM
I have DPI rocker arm stoppers. $30 shipped and Paypal'd. I can send you pictures if you want.

I also have a GReddy oil filter block so you can attach oil temperature and pressure gauges, but that's not really internals.