400 whp track car part out

[P-Funk alot]

ok guys look i tried to sell it as a complete car but it didnt work out so if the motor set sells i will part the whole car out but the motor set has to sell first.

full 400 whp rb25 turn key swap i will not seperate any part from this set.
looking to get 5k OBO

so with that being said here are pics of the car complete and running so let me know guys. i am motivated but not deperate



rb25 series 1
apexi power fc and commander
d werks 750cc injectors
greddy intake mani
cx racing turbo mani
greddy bov
new turbo custom built by performance technique (full boost under 3500 rpm its crazy)
tial 38mm waste gate
aem wideband
blitz d-sbc
completely rebuilt head
tomei valve springs and retainers
also have tomei solid lifters
real nardi deep corn steering wheel
nrg quick disconnect and hub
z32 maf
q45 throttle body
full 5 lug conversion
z32 front calipers
z33 slotted and cross drilled track rotors
tein inner and outer tie rods
god speed coils with swift springs 10/8k (i like them better then my old teins)
all suspension arms are also godspeed
steel one piece drive shaft
syko mount kit motor and tranny (also have mckinney ones that will be thrown in)
wagner pads front and rear (thing stops on a dime)
50mm over fenders in the rear
20mm wide fenders in the front
act clutch good for 600 hp (thing is like an on and off switch grabs super hard)


leave you negative comments out of my thread everyone as different opinions.

here are some pics ill have more up tomorrow that are more current.
http://i1219.photobucket.com/albums/dd438/pfunkalot/095.jpg
http://i1219.photobucket.com/albums/dd438/pfunkalot/060.jpg
http://i1219.photobucket.com/albums/dd438/pfunkalot/055.jpg
http://i1219.photobucket.com/albums/dd438/pfunkalot/030.jpg
http://i1219.photobucket.com/albums/dd438/pfunkalot/020.jpg


text me 909-763-0910

[Nicelyphe]

Bit interested in the cost on the overfenders for the front and rear, how do those hold up in weather conditions? Would be shipped to 18018. PM me, thank you. Also if the tails are for sale, let me know.

[wanabedrftr]

I'm interested in the skirts and rear bumper. Where are you located?

[iggyspeed]

Interested on wheels, seats, harness. Pm me prices whenever youre ready to part out.

[driftage240]

iill take the hood lmk asap 818 851 8491 fixed!

[iggyspeed]

iill take the hood lmk asap 818 851 841

Missing one more digit there sir.

[waxball88]

Price for wideband

[Joanne_Dub]

I will pay freight for the entire rb set up with trans

[armiller91]

interested in tails if you part out

[Joanne_Dub]

PM returned

[Big Zee]

z33 slotted and cross drilled track rotors
will these come with the brackets to hold the z32 calipers ?

how much for the set ? very interested

[drifter_for_life06]

im interested in tail lights and center garnish as well if you part out. Im not first in line, so if these other guys flake, let me know

[P-Funk alot]

ok guys as of right now the motor set is pending if i recieve the deposit i will begin the part out of the rest of the car

[Beejis60]

What seats do you have when/if parting?

[JAStirrett]

5 lug conversion shipped to 33716?

[armiller91]

ok guys as of right now the motor set is pending if i recieve the deposit i will begin the part out of the rest of the car

Awesome, Hopefully It goes through.
Im still interested in the Tailights with Center

Also might be intersted in the AEM Wideband and the Suspension..
If you have replaced it, I would like everything but the Coilovers

Anyway please PM me if/when you get it sold so we can talk
Thanks

[SLEEPYDUB]

I am highly interested in the PFC.
Is it still available?

[SoCaltC]

Pm'd but forgot to ask if it also comes with the S13 > RB wire harness? I assume it does but just wanted to double check. Thanks.

[P-Funk alot]

yes it will be a turn key swap with everything needed for it to be running in your car

[matthewAPM]

I PM'd you about a ton of stuff I want to buy and need ASAP.

[s14rb26]

Interested in the syko motor mount kit, does it come with downpipe. Is the kit for a Rb25 pm me a price will buy ASAP paypal ready

[s14rb26]

Will the syko mounts fit a s14

[P-Funk alot]

yes it will fit s14 it uses the r33 crossmember i no longer have the down pipe as that was for the stock turbo set up yes it is for rb25. i am not gonna part with that from the motorset as i am including that in the sale but i do have a mckinney set i could sell you pm me

[Joanne_Dub]

Pm'd you. My phone is off so if u could text me 9512413205

[Laotian240]

interested in front bumper pm price!

[240zach]

how much for tail light assembly?

[GRNxS14]

Size and a price for the nardi?

[P-Funk alot]

nardi is 350mm deeo corn

[brizzle3000]

do you have a turbo timer you want to sell?

[P-Funk alot]

ok guys buyers fell through need this motorset gone to begin partout

[blueshark123]

z33 slotted and cross drilled track rotors
will these come with the brackets to hold the z32 calipers ?

how much for the set

[Vernal]

how much for the coilovers?

[Sideways_blksr20]

Sell me ur transmission

[driftage240]

Sell me ur hooooood alreaddddy!!!!!!!!

[Kevin920415]

can you pm me for 5lug swap and the kouki tails picked up? thank you!

[matthewAPM]

I have sent a few PM's to you. Not sure if you got them. I want to buy the coils, kit, wheels, 5 lug etc

[bradass]

sell me your hood

[lowkey]

Free bump car is amazing and seller is legitt!!!

[P-Funk alot]

ok im ready to part this thing out motorset is still available but imma throw it in a coupe and get some freeway killings on lol.

[iggyspeed]

SEATS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!! how much prease?

[armiller91]

PM me. Im interested in Tails With Center, Tie Rods, and Wideband. Thanks

[P-Funk alot]

tails and hood are pending everything else is up for grabs

[Brock864]

i will take the greddy intake manifold right now. paypal ready just need your address.

-Corey

[P-Funk alot]

bump........

[ellocodiablo53]

R33 crossmember, syko kit, and driveshaft still for sale? I'll take them :D
text me (256)508-0575

[SLEEPYDUB]

powerfc available?

[semajnworb]

I am interested in the PFC
and the enitre chasis if the motor sales

[AnthonysSilvia]

intrested in your 50mm rear fenders? price?

[stamps31757]

i know this posting is old but what turbo do you have an how much are you looking to get from it.

I'm also interested in your down pipe.

PM me with prices if you dont mind.

[william's']

how about those wheels?

[twinspool]

what all have you sold off the motorset so far?
and what is still available?