Fearell
05-03-2011, 10:59 AM
I've got a project VR4 with about 140K and a clean chassis. I'm basically just too busy to finish this project right now. Everything is there and documented. I’ll give a complete list of stock and aftermarket parts if there is any interest in the car. This is the build thread I started: Project Big Huffer. - Page 2 - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f1/project-big-huffer-492091/index2.html)
So you’ll get a clean VR4 with a custom half cage and some expensive parts. I can arrange transport of the car and I can help with any other things that come up.
EDIT: List of parts that will be included:
-4 Bolt Engine
-Manual Tranny
-4" IPS Titanium Carbon Exhaust
-PTE 660 CC Injectors
-Walbro Fuel Pump
-Tien S-Tech Springs
-Stillen Cross Drilled Rotors and Pads
-2ed Gen Sideskirts
-2ed Gen Core Support + Headlight Buckets (NEW)
-2ed Gen Bumpers (Front + Rear)
-1st Gen Hood
-Ross pistons - these customs were custom ordered by Scott Merkel designed to be used in a stock bore engine with just a light hone ran through the cylinders. These are not off the shelf pistons. They come with the rings. I can send you a copy of the spec sheet if you want.
stock bore 3.587 w/ stock comp. ratio 8.0:1
These pistons have a few design differences vs. shelf Ross pistons -
-top chrome ring
-Merkel 3rd ring design
-Merkel CAM grind (skirt shape)
-16cc dish (shelf pistons are much lower)
-Oliver rods - These rods CAN be used in a 6G72 or can be used for Ray's stroker setup with his custom pistons.
-Custom pins by Merkel.
-OEM 120K Service Kit
(I have a folder full of info on the cage specs + suspension geometry + weight info [Each corner, front, rear etc])
Please PM or email me at [email protected]
http://i101.photobucket.com/albums/m54/3siphotos/MikesVR42.jpg
http://i101.photobucket.com/albums/m54/3siphotos/a47b8791.jpg
http://i101.photobucket.com/albums/m54/3siphotos/c5cd7a8d.jpg
The car will come with stock wheels. I'm looking to trade this project or get about 7K for it.
So you’ll get a clean VR4 with a custom half cage and some expensive parts. I can arrange transport of the car and I can help with any other things that come up.
EDIT: List of parts that will be included:
-4 Bolt Engine
-Manual Tranny
-4" IPS Titanium Carbon Exhaust
-PTE 660 CC Injectors
-Walbro Fuel Pump
-Tien S-Tech Springs
-Stillen Cross Drilled Rotors and Pads
-2ed Gen Sideskirts
-2ed Gen Core Support + Headlight Buckets (NEW)
-2ed Gen Bumpers (Front + Rear)
-1st Gen Hood
-Ross pistons - these customs were custom ordered by Scott Merkel designed to be used in a stock bore engine with just a light hone ran through the cylinders. These are not off the shelf pistons. They come with the rings. I can send you a copy of the spec sheet if you want.
stock bore 3.587 w/ stock comp. ratio 8.0:1
These pistons have a few design differences vs. shelf Ross pistons -
-top chrome ring
-Merkel 3rd ring design
-Merkel CAM grind (skirt shape)
-16cc dish (shelf pistons are much lower)
-Oliver rods - These rods CAN be used in a 6G72 or can be used for Ray's stroker setup with his custom pistons.
-Custom pins by Merkel.
-OEM 120K Service Kit
(I have a folder full of info on the cage specs + suspension geometry + weight info [Each corner, front, rear etc])
Please PM or email me at [email protected]
http://i101.photobucket.com/albums/m54/3siphotos/MikesVR42.jpg
http://i101.photobucket.com/albums/m54/3siphotos/a47b8791.jpg
http://i101.photobucket.com/albums/m54/3siphotos/c5cd7a8d.jpg
The car will come with stock wheels. I'm looking to trade this project or get about 7K for it.