FS: Complete S15 SR/6-Spd, Full-Race 3076R, PowerFC, Tial, Blitz, Greddy, Toda, Earls

[Broadfield]

As you may know, I am getting ready to swap in an LS3 over the winter. Considering nothing from this setup will be utilized for the V8 swap, I want to try and sell it as a complete drop-in swap... basically from the FMIC all the way back to the driveshaft and everything in between. This will be great for someone who is planning on an SR swap and is going to do a lot of top notch aftermarket to go along with it. It will save you a lot money in the long run. Drop it in and go, no tuning needed etc.

The fist dollar amount represents what I paid for everything. When I bought the stuff, I bought it for the cheapest I could find it at the time. All items were brand new at the time except for the motor and transmission of course. The dollar amount on the right represents a fair used price of what I would ask if I was parting it out. Keep in mind, all parts are in mint condition, as seen in pics. If I can't sell this thing as an entire package, then I will start to part it out. So these used prices will give you a really good idea of what I will be asking if that time comes.

With the purchase I will be including a brand new Wiring Specialties engine swap harness for your particular chassis. Mine is very specific to my vehicle and it will just be easier on everyone if I include a new one. I will most likely include the fuel pump(R33 GTR) and radiator fans(Spal) since I will probably need to run something different anyway. I didn't bother pricing in the little crap like the Turbo XS manual boost controller, new OEM water pump, oil pump etc. Nor the Gallery Fresh dress up bolts, as I feel those are for appearance purposes only and I don't expect to get anything for them. This setup also has full working A/C with the R134 compressor. It will include the custom lines to work in the S13 chassis.

So just to give you an idea, I have right at $19,000 into this list. Fair market used value comes out to $12,310. I am asking $11,000 as a package deal or OBO. Please post, PM or email me at: Toby.Broa[email protected] if you have any questions.

Also, please feel free to post if you have interest in a part or want to call dibs. This will help give me an idea of how much interest I have if it comes down to parting it out. NOTE: I am going to give this about 2 months before I part it. At that time I will contact anyone who has showed interest and post the rest for sale in a new thread(s)



$3500/$2900 S15 engine SOLD 6-speed trans still available; no more than 65,000 miles
$1500/$1000 Apexi Power FC D-Jetro(w/MAP and intake sensors) Tuned for 400whp and 333wtq
$1400/$800 Blitz twin disc clutch/flywheel
$500/$300 Driveshaft Shop aluminum driveshaft SOLD
$950/$450 Greddy FMIC (no piping)
$375/$200 Greddy oil pan (Will not part out, goes with long block) SOLD
$690/$350 Greddy radiator SOLD
$340/$100 Greddy aluminum pulleys SOLD
$50/$20 Greddy 4” intake filter SOLD
$550/$350 Greddy intake manifold SOLD
$550/$400 70mm throttle body N15 SOLD
$120/$75 Tomei N15 throttle body adapter SOLD
$1350/$950 Garrett twin scroll GT3076R .78 A/R (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$1500/$1000 Full Race twin scroll manifold SOLD
$349/$200 Full Race downpipe SOLD
$220/$130 Blitz downpipe
$99/$40 Full Race dump tube SOLD
$349/$200 Tial 44mm wastegate (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$219/$130 Tial 50mm BOV (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$550/$300 PE 850cc injectors SOLD
$400/$250 Splitfire coil packs SOLD
$530/$300 Toda 264 cams (Will not part out, goes with long block) SOLD
$225/$100 Toda valve springs (Will not part out, goes with long block) SOLD
$110/$50 PE Kevlar belts SOLD
$148/$80 Brian Crower titanium retainers (Will not part out, goes with long block) SOLD
$69/$30 Tomei rocker arm stoppers (Will not part out, goes with long block) SOLD
$40/$29 Golden Eagle vacuum box (Earls AN lines and fittings are not included, priced separately if you want them)
$115/$60 Billet oil filter relocate (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$109/$60 Samco radiator hoses SOLD
$350/$200 Hose techniques couplers and t-bolt clamps SOLD
$30/$15 Custom 4” intake pipe (Does not include Hose Techniques couplers/t-bolts, priced separately if you want them) SOLD
$50/$20 Custom 2-1/4” hot side piping (Does not include Hose Techniques couplers/t-bolts, priced separately if you want them) SOLD
$75/$30 Custom 3” cold side piping (Does not include Hose Techniques couplers/t-bolts, priced separately if you want them) SOLD
$225/$150 T1 crankcase breather box (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$1100/$600 All custom Earls braided nylon lines w/Earls AN fittings: fuel, pressure, oil, coolant etc. SOLD
??? Gallery Fresh anodized bolts SOLD
$125/$60 Turbo XS High Performance manual boost controller (Earls AN lines and fittings are not included, priced separately if you want them)
$125/$80 Aeromotive fuel pressure regulator w/Earls inline fuel filter (Earls AN lines and fittings are not included, priced separately if you want them) SOLD
$100/$40 Custom short throw shifter w/titanium shift knob (Will not part out, goes with transmission)


http://images12.fotki.com/v197/photos/4/47612/3915226/IMG_8258-vi.jpg

http://images43.fotki.com/v680/photos/4/47612/3915226/IMG_7464-vi.jpg

http://images40.fotki.com/v776/photos/4/47612/3915226/IMG_7474-vi.jpg

http://images19.fotki.com/v677/photos/4/47612/3915226/IMG_7479-vi.jpg

http://images56.fotki.com/v774/photos/4/47612/3915226/IMG_7481-vi.jpg

http://images17.fotki.com/v313/photos/4/47612/3915226/IMG_7497-vi.jpg

http://images17.fotki.com/v313/photos/4/47612/3915226/IMG_7540-vi.jpg

http://images17.fotki.com/v274/photos/4/47612/3915226/IMG_7573-vi.jpg

http://images19.fotki.com/v678/photos/4/47612/3915226/IMG_7484-vi.jpg

http://images112.fotki.com/v590/photos/4/47612/3915226/IMG_7608-vi.jpg

The following pictures were taken by Nate Hassler of Modified Magazine:

http://images50.fotki.com/v405/photos/4/47612/3915226/DualS13Feature_02-vi.jpg

http://images57.fotki.com/v496/photos/4/47612/3915226/DualS13Feature_03-vi.jpg

http://images107.fotki.com/v84/photos/4/47612/3915226/DualS13Feature_04-vi.jpg

http://images16.fotki.com/v3/photos/4/47612/3915226/DualS13Feature_05-vi.jpg

http://images16.fotki.com/v3/photos/4/47612/3915226/DualS13Feature_06-vi.jpg

http://images9.fotki.com/v55/photos/4/47612/3915226/DualS13Feature_07-vi.jpg

http://images58.fotki.com/v696/photos/4/47612/3915226/DualS13Feature_08-vi.jpg

http://images41.fotki.com/v1243/photos/4/47612/3915226/DualS13Feature_09-vi.jpg

[xpertsnowcarver]

Interested/Dibs on your driveshaft. Please confirm that it is for a 6 Speed to S13 open differential.

Sorry to hear about this part out. Always been a fan.

Edit: What exactly is custom about the short shifter?

I'm also interested in your Greddy Radiator.

[NismoMax]

Why couldnt you have put this up in may?!?!

[reds13se]

deff interested in the blitz bov....i would be honored to run it.....im curious to see the swap....shits gonna be sick like always!

[TriniGT]

Should be interested in injectors, coilpacks, Toda cams, springs and retainer and pulleys. Need to have them all shipped to Trinidad in the Caribbean. Postal code TT. I know prices are good but let me know what package price can be arranged. Would love to take the turbo setup but just don't have the cash now. This setup is awesome.

[mxsx25]

Wow ... your engine bay leaves me speechless

[sr20drifter1]

Dibs on custom oil catch can and Goldeneagle vaccum with earls fitting that go with them.I will also take the OEM cooler tank.

[240knockout]

Hey this is Ralph...I sent you an email. Looking to buy as soon as u decide to part.

[ss1156ss]

All I can say "Holy Crap..... that is absolutely awesome!!! :eek2::bowdown::drool::drool::drool: GLWS, if I hit 6 numbers tonight I will be giving you a call!!!

[Couped_up'd]

I got a new wall paper.

[Irresistible]

May I ask what you wrapped your P/s reservoir and half of your BMC in? The gold foil, what exactly is it? I assume it's to keep the fluids cool, but what's the name of the foil? Thanks in advance.

[TOMEI GUY-S13]

wow Broadfield, I just saw the article in Modified mag with your car. I cant believe that your selling the setup. hope the LS works out for ya. Im hopeing that my build gets off the stand and in my car. lol I want you to build the same cluster that you have in the s13. its amazing. anyway good luck man.

[felicianod83]

Oh man with the sell of the S15, Im hearing new Cluster being built by toby !!

[s14canyoncity]

wow very nice .... glws

[RHDskyline]

Whats all included in the oil filter relocation?

does it include the lines and such?

PM me thanks

[burninskulls0911]

man, you have the nicest looking sr i have ever seen, props to you for the good work.

GLWS

[nathanong87]

wish i was 5 lug

[SammyGreen]

May I ask what you wrapped your P/s reservoir and half of your BMC in? The gold foil, what exactly is it? I assume it's to keep the fluids cool, but what's the name of the foil? Thanks in advance.

You can order it through pretty much any auto parts store, its like a thermo wrap that sticks on. I used a lot of it in my STi when I had it works very well to keep heat away.


ANYWAYS... Id def be interesting in taking the Aeromotive Fuel Pressure Reg at time of part out if it happens.

Amazing car btw! Love it.

[PerilousActs]

Dibs on the rocker arm stoppers.

[whiterps13]

wish i was 5 lug
Hahahah! Best post ever.

I will vouch for this setup. It is just as clean in person and is absolutely wicked fast.
Somebody buy it and be an instant G.

[m2mike]

someone buy this as a package! this motor is too sweet to be parted out!
if this was posted 3 months earlier, i would've bought it :( i spent more money then what he's selling for and still can't come close to what he's done to his motor.

[road bandit sx]

Does anyone know the HP this set has to the wheels?

[kamechikara]

Pulling an install like that is fawkin we todd edd...parting it is fail of the year.

[chiboy002]

May I ask what you wrapped your P/s reservoir and half of your BMC in? The gold foil, what exactly is it? I assume it's to keep the fluids cool, but what's the name of the foil? Thanks in advance.
Mishimoto "Heat Defense" Heat Protective Tape: <font color="#ccoooo">FREE SHIPPING</font> (http://intensepower.com/mihdeheprtaf.html)

It's like this, but probably another company?

[kyles1988]

Does anyone know the HP this set has to the wheels?

400whp
333wtq.

It's in the OP

[Broadfield]

Pulling an install like that is fawkin we todd edd...parting it is fail of the year.

It's not getting parted. I have every intention of selling it as a package. I will give it up to two months, then part if necessary.

[Broadfield]

deff interested in the blitz bov....i would be honored to run it.....im curious to see the swap....shits gonna be sick like always!

I don't have a Blitz BOV???

May I ask what you wrapped your P/s reservoir and half of your BMC in? The gold foil, what exactly is it? I assume it's to keep the fluids cool, but what's the name of the foil? Thanks in advance.


Design Engineering DEI 010393 - DEI Reflect-A-GOLD Heat Barriers - Overview - SummitRacing.com (http://www.summitracing.com/parts/DEI-010393/)

Whats all included in the oil filter relocation?

does it include the lines and such?

PM me thanks

The price listed only includes the filter mount and the block adapter. The lines would be extra. I would figure a price for those if the time comes. Right now I just have the relocate lines listed under AN lines. If I part out I will make new threads to list things as small packages. IE: oil filter relocate with the lines. Or breather tank with lines. Etc. I simply listed things how I bought them. I had to make all of the lines custom, so I listed what I spent on the lines and fittings as a whole.

[htownsr510]

Daym u I just bought greddy oil pan and pulleys and payed way more

[Josho]

I have never seen this car before!! Its sooo sick dude!

[bb4_96]

blow off valve looks like a tial.

Which pulleys are included for $100? I can only see the water pump pulley. Is the wp pulley overdriven?

Thanks

[Broadfield]

blow off valve looks like a tial.


Yeah, I know what I got man:wtf:

Besides, it's posted right in the list what it is.


Which pulleys are included for $100? I can only see the water pump pulley. Is the wp pulley overdriven?

Thanks

It's the standard 3-piece Greddy set: Water, alternator and power steering.

[D.Adams]

I hate to watch this get parted out but i know whatever you build after this set up will be fucking epic.



Dibs on

Greddy oil pan
Greddy aluminum pulleys
Splitfire coil packs
PE Kevlar belts
Billet oil filter relocate
Samco radiator hoses
Tomei rocker arm stoppers

[koharatx]

NOOO!!! I just read the article on your car in Modified yesterday!

I'm deployed in Afghanistan and recently bought a 1993 240SX coupe, in white ahaha! It is in "incomplete SR20 swap" phase. It's mostly done, but I need to complete it.

It's a shame to see such a clean build get pulled apart, but I'm a huge fan of the LS engine as well! I bet your new build will be sick!

I wish I could buy this, but it's just not possible right now. People are already calling dibs on things I'm interested in, but just in case, here's what I'm interested in:

Radiator
Pullies
Intake filter
Either Downpipe (one or the other)
Dump tube
BOV
Injectors
Cams
Valve Springs
Belts
Retainers
Rocker arm Stoppers
Oil filter relocate
Intake/hot/cold piping
FPR w/filter

Sorry, it's most of the small stuff. I would guess you would sell some of this by the time you get to me, so let me know what's left if it comes down to parting out the build. Good luck with the sale, and good luck with your next build!

[koharatx]

By the way, why did it cost so much for hose and AN fittings?

I destroy those things day in/day out for the Army. I'm a hydraulics mechanic :-P

I know they're expensive, especially when you get to -16 size fittings and such. But for what I'm guessing is mostly -6? Holy crap!

[1gr8bar10der]

An epic FS thread LOL. Subscribe!

[Broadfield]

By the way, why did it cost so much for hose and AN fittings?

I destroy those things day in/day out for the Army. I'm a hydraulics mechanic :-P

I know they're expensive, especially when you get to -16 size fittings and such. But for what I'm guessing is mostly -6? Holy crap!

Well, even -4 braided nylon hose is $10/ft. The -10 swivel 90 degree ends like on the valve cover are $25 each for example. So it easily adds up. And to be honest with you, I actually spent more than what I posted on all of the AN stuff.

[koharatx]

Well, even -4 braided nylon hose is $10/ft. The -10 swivel 90 degree ends like on the valve cover are $25 each for example. So it easily adds up. And to be honest with you, I actually spent more than what I posted on all of the AN stuff.

Hmm... sounds about right. I guess I just never realized how much it was to plumb a complete car. I did notice you used Earl's for all your AN stuff. IIRC, Goodrich actually supplies Earl's.

Sorry, I don't want to clutter your sale thread. But whoever buys those lines is getting a hell of a deal. Actually, anyone who picks anything up here, whether it's the full setup or a few pieces should be very happy when all's said and done!

[drifter_for_life06]

I'll take the injectors if u part out. Good luck selling.

[greenman100]

Interested in Greddy 4” intake filter and pipe/coupler.

[rawkusx187]

I'm sure it will be a bitch to get some to buy as a package but im interested in the Tial bov and WG. Hit me up incase you decide soon.

[ROOSEY]

absolutely incredible package just saw the latest mag and all i can say is WOW im crying on the inside becuase of how badly i want this motor in my vert glws. someone is going to be a very very happy buyer. im also watching your LS build thread good luck with it all man!

[fearlessKouki]

I'll take the oil filter relocation kit, hot side And cold side intercooler piping! Please let me know if u part out and btw u have best looking engine bay!

[fearlessKouki]

I'll also take Toda camshaft, Toda Valve springs, BC retainers, TOmie rocker arm stopper. Thanks

[kyles1988]

Pretty sure that IF it does come down to parting out, he's not going to be parting out every single engine component. IE: the engine will be a complete longblock with cams/retainers/pistons/any other request along those lines.

Correct me if I'm wrong Tob.

[fearlessKouki]

I'm pretty sure if he posted to sell those in part out list then he will. but it's up to him :)

[Broadfield]

I'm pretty sure if he posted to sell those in part out list then he will. but it's up to him :)

As Kyle stated, this is not a part out list. This is a list to show what parts are included in the entire package. I have a used price listed next to each item to illustrate how I came up with a package price. If this does not sell within a couple months, then I will make a new thread(s) to part out the setup. However, I will not be parting out engine internals, pulleys etc. Those will need to go with the motor seeing as I do not really have any of the OEM parts left over.

[Cannonblaster]

Great! i finally have something to refinance my house!!!!!
GLWS hope someone buys in bulk.. but not me!

[sidewaysil80]

I know you said you wouldn't part out the engine...but how would you feel about selling the 6spd transmission? i'd like to keep an extra in case mine ever shits the bed...

[Broadfield]

I know you said you wouldn't part out the engine...but how would you feel about selling the 6spd transmission? i'd like to keep an extra in case mine ever shits the bed...

Yes, I would part the transmission from the engine.

[nissangtr1]

Interested in complete intake mani when ur ready to part out.

[sidewaysil80]

Yes, I would part the transmission from the engine.

awesome! please pm if/when you decide to do the partout. thanks.

p.s.
did you get my pm

[Dude4253]

Do you have pictures of the short shifter? (i can only assume it's pretty quality)
I dont know what everyone has already "dibs" but if I would be interested in these parts:
Greddy 4” intake filter
Custom 4” intake pipe
Splitfire coil packs
Toda 264 cams
Toda valve springs
Tomei rocker arm stoppers
T1 crankcase breather box
Aeromotive fuel pressure regulator w/Earls inline fuel filter
Custom short throw shifter w/titanium shift knob
Golden Eagle vacuum box

[kyles1988]

please read before posting.

[xpertsnowcarver]

Yes, I would part the transmission from the engine.

In which case, please sell me your driveshaft. :) I'm ready to purchase it.

[Wake]

Toby I will take your entire vacuum setup and probably most of the -AN lines when you decide to part.

Honestly hate to see it go I m almost willing to donate another chassis for your build so you dont take this one apart. It needs to be in the Nissan museum or something.

[RickyS13.]

Hate to see this setup go, it was one of my favs.

On the plus side, LS3 coming :naughtyd:

[chiboy002]

dibs for the oil relocation as well lol

[Imarvin240]

i loved the article on this, such a great and well built car. also, you do some great custom gauge work...il probably send you a message tonight about that too. if you do end up parting it out, please keep me in mind for these parts.

Golden Eagle vacuum box
Blitz twin disc clutch/flywheel
Greddy radiator
T1 crankcase breather box

good luck with the sale and the next build, im sure it will be amazing when its all completed

[240sr20swap]

how much for short shifter shipped 61820 PM me

[Broadfield]

Toby I will take your entire vacuum setup and probably most of the -AN lines when you decide to part.


Noted!

In which case, please sell me your driveshaft. :) I'm ready to purchase it.

Noted!

i loved the article on this, such a great and well built car. also, you do some great custom gauge work...il probably send you a message tonight about that too. if you do end up parting it out, please keep me in mind for these parts.

Golden Eagle vacuum box
Blitz twin disc clutch/flywheel
Greddy radiator
T1 crankcase breather box

good luck with the sale and the next build, im sure it will be amazing when its all completed

Dibs has already been called on the vacuum box and breather box. But you are good on the clutch and radiator.

EDIT: I went back and noticed someone called dibs on the radiator. So if they back out you are second on the list.

how much for short shifter shipped 61820 PM me

I may not part the short shifter unless you have an OEM one to give me. You do realize this is for a 6-speed?

[Future_gohan]

You should sell this to me in payments so i can put it in my z32. :)

GLWS! Whoever gets it should be one happy motherfacker.

[xpertsnowcarver]

Noted!

Dibs has already been called on the vacuum box and breather box. But you are good on the clutch and radiator.

EDIT: I went back and noticed someone called dibs on the radiator. So if they back out you are second on the list.

I may not part the short shifter unless you have an OEM one to give me. You do realize this is for a 6-speed?

Awesome. :)

If you're referring to me on the radiator, I'll forfeit calling dibs on it. The radiator was something I needed right away, so I went ahead and purchased one.

I'm still interested in the shifter. I can provide you with my OEM 6-speed shifter as well. My transmission has less than 29,000 miles on it. :)

[rawkusx187]

I been checking this thread on a daily waiting for you to decide to partout :)

[Yuda]

fukn topnotch motor.

[sleeper108]

I would call dibs on:
Aeromotive fuel pressure regulator w/Earls inline fuel filter


I didnt see anyone else mention it, unless I skipped over it... let me know when, cause I got cash readddyyy


edit:
just saw people say they were interested in it, but nonetheless, I would jump on it if they didn't

[TOMEI GUY-S13]

hey broadfield. is this a built engine or jdm swap. interested pm please.

[slowerthanyou]

ill take all of this as soon as tax time rolles around if your not parting it out by then..

$50/$20 Greddy 4” intake filter
$1350/$950 Garrett twin scroll GT3076R .78 A/R
$1500/$1000 Full Race twin scroll manifold
$349/$200 Full Race downpipe
$99/$40 Full Race dump tube
$349/$200 Tial 44mm wastegate
$219/$130 Tial 50mm BOV
$69/$30 Tomei rocker arm stoppers
$350/$200 Hose techniques couplers and t-bolt clamps
$30/$15 Custom 4” intake pipe
$50/$20 Custom 2-1/4” hot side piping
$1100/$600 All custom Earls braided nylon lines w/Earls AN fittings: fuel, pressure, oil, coolant etc.

[tacoboy]

dibs on the Aeromotive afpr and the samco hoses

[Broadfield]

hey broadfield. is this a built engine or jdm swap. interested pm please.

I'm not really sure how to answer your question or what you are really asking me!?!

It's an S15 motor which is obviously not from this country originally. Is it built?... kind of. The head is, but the bottom end isn't. I will send you a PM.

[Broadfield]

LET THE PART OUT BEGIN!

I will be contacting through the week those, in order, that have called dibs and then those that have showed interest. Keep in mind that this is not the only place I have this stuff posted for sale. So just because you called dibs first on Zilvia, doesn't mean you called dibs first on this planet. A lot of people PM'd or emailed me their requests also. I will be making a new for sale thread for everything. Then clarifying what does and does not get separated from each other. Even if you called dibs, feel free to PM me to express your interest and let me know you still want it.

Please keep in mind I am a VERY busy individual and I will contact you eventually. If you called dibs first then you have nothing to worry about. I will not sell it out from under you. However, if someone called dibs before you on another forum or emailed me, then you obviously do not have first dibbs overall... Zilvia is NOT the only place this stuff is for sale.

[TriniGT]

Samco radiator hoses, Greddy Pulleys, Kevlar Belts and coilpacks all shipped to Trinidad in the Caribbean. Postal Code is TT. Let me know, I inquired on these earlier. PM me back please.

[koharatx]

NOOO!!! I just read the article on your car in Modified yesterday!

I'm deployed in Afghanistan and recently bought a 1993 240SX coupe, in white ahaha! It is in "incomplete SR20 swap" phase. It's mostly done, but I need to complete it.

It's a shame to see such a clean build get pulled apart, but I'm a huge fan of the LS engine as well! I bet your new build will be sick!

I wish I could buy this, but it's just not possible right now. People are already calling dibs on things I'm interested in, but just in case, here's what I'm interested in:

Radiator
Pullies
Intake filter
Either Downpipe (one or the other)
Dump tube
BOV
Injectors
Cams
Valve Springs
Belts
Retainers
Rocker arm Stoppers
Oil filter relocate
Intake/hot/cold piping
FPR w/filter

Sorry, it's most of the small stuff. I would guess you would sell some of this by the time you get to me, so let me know what's left if it comes down to parting out the build. Good luck with the sale, and good luck with your next build!

Dang... didn't know the difference between interested/dibs. Oh well. I'm still interested in all the above. Whatever hasn't been dibs'd out--I'm ready to make a selection and send payment on.

[chiboy002]

worst timing every toby, worst timing ever.

[Om1kron]

put me down for the list of potential buyer, but guaranteed flaker.

[EDacIouSX]

I'm interested in the oil pan, pulleys, and belts among other parts. let me know when/if you decide to part out please!

[crescendo]

TODA cams if no scaring is present on lobes or journals. Paypal ready right now. 95833.
[email protected]

[inFAMOUSbz]

Would you be willing to part out your AC lines or AC set up? Also interested in the short shifter. Please PM me. Thanks!

[moskoxxx]

do you have s15 lhs rear quarter glass ?

[Broadfield]

Samco radiator hoses, Greddy Pulleys, Kevlar Belts and coilpacks all shipped to Trinidad in the Caribbean. Postal Code is TT. Let me know, I inquired on these earlier. PM me back please.

PM'd

Dang... didn't know the difference between interested/dibs. Oh well. I'm still interested in all the above. Whatever hasn't been dibs'd out--I'm ready to make a selection and send payment on.

I will let you know how it works out

worst timing every toby, worst timing ever.

The worst timing for one guy is the best timing for another. Why is it bad timing?

put me down for the list of potential buyer, but guaranteed flaker.

Gotcha!

I'm interested in the oil pan, pulleys, and belts among other parts. let me know when/if you decide to part out please!

I will not part out the pan or pulleys unless you have stock ones you can give me.

TODA cams if no scaring is present on lobes or journals. Paypal ready right now. 95833.
[email protected]

PM'd

Would you be willing to part out your AC lines or AC set up? Also interested in the short shifter. Please PM me. Thanks!

Absolutely on the AC compressor. Not sure on the lines yet. I'll have to wait and see if I decide to do AC on the LS3 swap. Which that could be a few months before I know that.

do you have s15 lhs rear quarter glass ?

Yes, those are still available. I also have the S16 front tow hook if you want that.

[sidewaysil80]

PM'd
I will not part out the pan or pulleys unless you have stock ones you can give me.

fwiw i have stock replacements for both toby...let me know if you need them.

p.s.
i'm flaking on the transmission dude, when mine goes i'm going 5spd.

[moskoxxx]

excuse me that question was not for you
I missed

[Broadfield]

fwiw i have stock replacements for both toby...let me know if you need them.

p.s.
i'm flaking on the transmission dude, when mine goes i'm going 5spd.

How much would you want for them? I was hoping who ever wanted to buy mine would simply give me their stock ones. It's not really worth it to me to pay for stock ones and shipping, just to make a little on the aftermarket parts. If that was the case I'd simply leave those parts on the long block and sell them with it.

No biggie on the trans, I have a few people interested.

[Broadfield]

excuse me that question was not for you
I missed

No problem, I knew something was up... random question of the month.

I was obviously being a smart-ass in my reply.:D

[sidewaysil80]

How much would you want for them? I was hoping who ever wanted to buy mine would simply give me their stock ones. It's not really worth it to me to pay for stock ones and shipping, just to make a little on the aftermarket parts. If that was the case I'd simply leave those parts on the long block and sell them with it.

No biggie on the trans, I have a few people interested.

you have a pm

[xpertsnowcarver]

I haven't received a PM about the driveshaft :cry:

I'm serious. PM me your paypal address and your final price.

[Broadfield]

I haven't received a PM about the driveshaft :cry:

I'm serious. PM me your paypal address and your final price.

I have not contacted a single person yet except for those that posted here since yesterday. I will be contacting people throughout the week. With my daily routine at work then all of the internet sales at night, I work about 12 hours every single day. Then a little time for my family and trying to get my swap going. So people will need to be patient.

My final price is what's posted. Keep in mind, you are not thee first person with dibs. I have a friend in the Chicago area that called dibs before I even posted this stuff up for sale on here. However, if he doesn't want it, then it's yours. I'm not sure how much shipping is though. I'll get an estimate for that.

[vg33er200sx]

mmm, if it comes to parting, hit me up for interested in the transmission.

[Broadfield]

mmm, if it comes to parting, hit me up for interested in the transmission.

I am in the process of parting as we speak. It will be a couple weeks before I have the actual long block and trans out. I left everything in the car until last night just in case a potential buyer wanted to hear the thing run or go for a drive, weather permitting. But I have waited long enough, so I started tearing the engine bay down last night. I need to get a cherry picker over to my house then simply find the time to get the motor/trans out... so that's why I'm giving it a couple weeks. PM me if you want to discuss price.

[TriniGT]

Well let me know in any event on the coilpacks, rad hoses and pulleys/kevlar belts if you don't hear from the others.

[xpertsnowcarver]

I have not contacted a single person yet except for those that posted here since yesterday. I will be contacting people throughout the week. With my daily routine at work then all of the internet sales at night, I work about 12 hours every single day. Then a little time for my family and trying to get my swap going. So people will need to be patient.

My final price is what's posted. Keep in mind, you are not thee first person with dibs. I have a friend in the Chicago area that called dibs before I even posted this stuff up for sale on here. However, if he doesn't want it, then it's yours. I'm not sure how much shipping is though. I'll get an estimate for that.

Awww fudge. Was hoping I was the first. Alrighty, I'll be on my toes. :bite:

[hksztss]

you have better pics of hot side piping and cold side piping trying to see if it will work with my setup which is almost exactly the same just hard to tell what happens after it goes threw wheel well, also interested in split fire coil packs

[EDacIouSX]

that 600 dollar intercooler price tag, does that include the intercooler piping?

[Broadfield]

that 600 dollar intercooler price tag, does that include the intercooler piping?

You must not of read the description very well:)

$950/$450 Greddy FMIC (no piping)

[EDacIouSX]

You must not of read the description very well:)

i don't remember all that bold stuff being there last i looked

[Broadfield]

Yeah, I edited the listings to reflect what is actually getting parted out. This thread was never meant to be a part out. It was simply a list to show what the "complete" setup included and what said parts were valued at new/used. So now that I am parting it out, I went back and noted what can be bought separately and what goes with the long block etc. So the FMIC core is $450 without piping.

[Bigt92604]

how much for the aeromotive fpr shipped to 89166

[Hoffman5982]

Have the gallery fresh valve cover bolts been claimed?

[TriniGT]

Let me know if the things I want are gone or not.

[EDacIouSX]

Yeah, I edited the listings to reflect what is actually getting parted out. This thread was never meant to be a part out. It was simply a list to show what the "complete" setup included and what said parts were valued at new/used. So now that I am parting it out, I went back and noted what can be bought separately and what goes with the long block etc. So the FMIC core is $450 without piping.

Ah, then my reading comprehension's not as bad as I was accused of. That is a relief.

Good luck with the part out. :)

[HOOCH]

Emailed you about the pulleys would like them right meow please!

[JesusFast]

When are parts going to be ready for pickup?

[Broadfield]

how much for the aeromotive fpr shipped to 89166

$90 shipped... I think I have a guy making a payment on it, but not 100% sure.

Have the gallery fresh valve cover bolts been claimed?

Officially they have not been claimed yet. They are not cheap though... let me know if you want a price.

Let me know if the things I want are gone or not.

Will do!

Ah, then my reading comprehension's not as bad as I was accused of. That is a relief.

Good luck with the part out. :)

LOL, thanks man!

Emailed you about the pulleys would like them right meow please!

Emailed you back.

When are parts going to be ready for pickup?

The stuff is coming out right now. The snow storm we had delayed me on getting the actual engine/trans out for another couple weeks... waiting for my engine hoist to get here. But all of the bolt-on stuff is coming out now.

[Hoffman5982]

yea i know they aren't cheap. how much do you want?

[Broadfield]

yea i know they aren't cheap. how much do you want?

$125 shipped... and actually you can't even buy these from Gallery. I bought the red cup washers from them, but then custom ordered the stainless shoulder bolts from a place out of Chicago. Then simply polished the heads. Those stainless shoulder bolts were $8 each alone... and there is 14 of them.

[Bigt92604]

Lmk if someone else has claimed the fpr interested in it

[Craig Jr]

Pm me lowest price shipped on the greddy frontmount to 91316. Also any pictures of it?

[Broadfield]

Lmk if someone else has claimed the fpr interested in it

Working with a guy now. I'll let you know if he backs out.

Pm me lowest price shipped on the greddy frontmount to 91316. Also any pictures of it?


I can do $450 shipped.

I happened to snap a quick pic last night. I can take more specific ones tonight if you need them. I didn't bother to clean it up yet:

http://images43.fotki.com/v1329/photos/2/47612/9485407/IMG_0199-vi.jpg

[hksztss]

hey man im super interested in intercooler pipe just looking for better pictures so i can see if it works with my full race setup also does coldside have -6an bung welded on it for Idle air control valve?

[lewisfk]

is the turbo set up gone?

[Broadfield]

hey man im super interested in intercooler pipe just looking for better pictures so i can see if it works with my full race setup also does coldside have -6an bung welded on it for Idle air control valve?

PM sent and yes it does have a -6 port for the IACV.

is the turbo set up gone?

It is still available. I have contacted the first two people with dibs, but have not heard back from them. I just contacted the 2nd guy inline tonight, so I'll give him at least a couple days to reply before I move onto the next guy.

What all were you wanting?

[ohhhizzzy]

im interested on the tial bov and the cold side piping how much shipped to 53114 thanks

[jubee]

Hey PMed you and email you on the IC piping have cash ready to buy ASAP

[Inland180]

Payment sent for some parts! Thanks

[Broadfield]

im interested on the tial bov and the cold side piping how much shipped to 53114 thanks

Hey PMed you and email you on the IC piping have cash ready to buy ASAP

Sorry, they have been sold.

[rebornS14]

do the belts and pulleys work on a S13 SR?

[TriniGT]

Any of the stuff I wanted still remaining, i.e. coilpacks, rad hoses and pulleys?

[Broadfield]

do the belts and pulleys work on a S13 SR?

I know the belts will not and I don't think the pulleys will either.

Any of the stuff I wanted still remaining, i.e. coilpacks, rad hoses and pulleys?

You are next in line. I will keep you updated.

[TriniGT]

Good to hear :D. Belts as well if they are still there.

[Ilikecars]

i want the kevlar belts they in good condition and will they fit redtop?

[Ilikecars]

NM i dont read so well

[darkevildrifter]

<LI itxtNodeId="390" itxtHarvested="1">$400/$250 Splitfire coil packs will buy these if you still have them

[Broadfield]

<LI itxtNodeId="390" itxtHarvested="1">$400/$250 Splitfire coil packs will buy these if you still have them

Sorry, they have sold.

[damnu]

turbo xs BC-HPBC? how much?

[Broadfield]

turbo xs BC-HPBC? how much?

$65 shipped

[m2mike]

How much is long block + tranny? What does it include?

[Broadfield]

How much is long block + tranny? What does it include?

$2910 if you take it all.

Let me steer you in the right direction!

http://zilvia.net/f/sale-items/367650-broadfields-partout-leftovers-s15-sr-w-6-speed-full-race-powerfc-blitz.html


Please let me know if you have any questions whatsoever. I tried to explain exactly what is included and what is not. Also what is needed to make it a complete start-up swap if that's what the customer is looking for.

Toby

[EDacIouSX]

i'll take the pe belts. please pm me with paypal info and if you need the belts off my motor.

[Broadfield]

i'll take the pe belts. please pm me with paypal info and if you need the belts off my motor.

Cool, PM sent! I do not need your belts.

Thanks,

Toby

[B4THEZ]

Does any one know if I can use this longblock on my sr20det notch top blacktop ? Also I will like to keep my 5 speed instead of the 6 speed trans.

Thanks

[B4THEZ]

Sorry, I double post