s14 with clean rb26dett swap. :P

[Speedfreak]

Here is a couple shots of my baby. I have since switched to a big single turbo set up T67 with a 100 shot of funny gas to help spool up on the launch as well as put in a Meth kit.
Engine mods
Bored 40 over
rb26dett from an r33
ARP Head studs and main studs
Tomei Metal gasket kit
HKS 264 cams
Tomei cam gears
CP Pistons
Eagle Rods
ACL Race bearings
t67 Garret turbo pushing 25 lbs
Nismo light weight flywheel and Nismo twin plate clutch
Koyo Radiator
1000cc HKS injectors
SDS standalone set up
Snow Performance Meth kit
NX Nitro kit (100 shot)
tial 38mm wastegate with screamer pipe, dont like the sound and am going to reroute it.
3inch custome exhaust
r33 rear diff. Went through 3 240sx diffs so had to goto better ring gears. :D

Suspension
Megan Race spec coilovers
every Megan suspension piece that you could get is in there.
energy suspension kit. IE. all the bushing are now either urithane sp. or metal

tranny is a stock 300zx tranny with a rb25det bellhousing on it.

Tires are 17x45x275 on front Nitto NT-01's Rear is 17x35x315 Nt-01's

cockpit
Autometer luner speedomiter,rpm,oil presure,water temp,egt,fuel level and boost
Custom made dash insert for Greddy E01 boost controller
http://px6.streetfire.net/0001/25/80/1485208_600.jpg
http://px6.streetfire.net/0001/25/50/1485205_600.jpg
http://px6.streetfire.net/0001/25/70/1485207_600.jpg
http://px6.streetfire.net/0001/25/60/1485206_600.jpg
BTW Had to cut the cf hood to make the engine fit and just havent had time/effort to refiberglass it. Might do it this winter.
also here a small vid.....
http://px5.sfstatic.com/thumbs/0000/01/87/201078.jpg (http://www.streetfire.net/video/drifting-240sx-silvia-rb26dett-swap_201078.htm?ref=7a3d7346-0ef9-4ecb-adbd-99af00d15a49)Drifting 240sx silvia rb26dett swap. (http://www.streetfire.net/video/drifting-240sx-silvia-rb26dett-swap_201078.htm?ref=7a3d7346-0ef9-4ecb-adbd-99af00d15a49)

[omgRWDgoodness!]

If only your taste in exterior styling matched your taste under the hood...that front bumper & wing is straight out of 2001, Fast and the Furious status dude.

[chetacheese]

niceeee engine and bay. the rest..... ehhh....

[jdm213]

niceeee engine and bay. the rest..... ehhh....


yeah only the engine is nice, the rest is all fast and furious :jerkit: ps that chick is hella ugly

[drift213]

2 fast 2 furious 2 fast for yallll lol nice motor though

[travisty_]

F&F steez. Nice motor.

[driftsilvias13]

So why did you make your own thread??

[AnotherZenkiKid]

stock mated z32 tranny can handle 25 psi of boost and nitrous?!

and yes i would love to know why you made your own thread when there was a post your pics here thread D;

[hisoka]

nice setup under there.

were is your CAS ? and why did you choose to use that radiator as opposed to a ca or rb one, then you wouldnt have to run that gay looking pipe across the front of the motor

either way this thing would be a weapon

[Speedfreak]

nice setup under there.

were is your CAS ? and why did you choose to use that radiator as opposed to a ca or rb one, then you wouldnt have to run that gay looking pipe across the front of the motor

either way this thing would be a weapon
I have an SDS stand alone that uses magnets on the crank pulley for a CAS.

As far as the radiator that is the what I had. That is from my sr set up. As far as the body kit. Well, its a Veilside kit I bought back in 97 and never changed it so ya. Sure its got its F&F look but I have owned this car and had this kit on it way before a movie came out so no... I didnt go for what a movie was, I went for what I wanted over 13 years back. But just remember this. It isnt what you want on a car. It is what I want. I love my ride.

[Ali 556]

1- Full navan aero.

2- mikkiny engine mount ts to sit it lower.

3- better hood.

4- better rims.

5- 50mm over wide rear fenders

Win ?

[ThatGuy]

Been a member since 2003, yet you can't find the Picture Thread?

:duh: :lockd: