PDA

View Full Version : Dumb question, is my TOB installed right?


StryfeS13
09-27-2010, 02:58 AM
I think I did it wrong.

http://i53.tinypic.com/4gpv1z.jpg
http://i56.tinypic.com/1fz6rp.jpg
http://i54.tinypic.com/dxoff7.jpg

negrosx13
09-27-2010, 03:01 AM
looks about right

Slidin' Sam
09-27-2010, 03:22 AM
looks legit...kinda hard to tell with those pics, but it looks ok.

StryfeS13
09-27-2010, 03:25 AM
Kinda hard to get the camera in there. sorry for bad pics

Pretty much there's a clip on the shifter fork. I attached it to the pivot ball, and clicked the clip in place, as shown in picture 1.

Then there's a clip that goes around the back of the throw out bearing shaft thing, and I placed it on the ends of the shifter fork, as seen in pictures 2 and 3.

nissanfreak317
09-27-2010, 09:42 AM
Are you having trouble getting the transmission back on the engine?
Or just unsure of how this goes together?

Seems like you have it right from the pics.

SinGarage
09-27-2010, 05:00 PM
Looks right to me also from the pics.

WholeGrainS13
09-27-2010, 06:21 PM
Looks like mine.

codyace
09-27-2010, 06:49 PM
Make sure you lube that shaft up before install

nissanfreak317
09-27-2010, 09:28 PM
Make sure you lube that shaft up before install

Never can have too much lube on that shaft before insertion. :keke:

negrosx13
09-28-2010, 06:44 AM
pliot bushing should be looked at

codyace
09-28-2010, 09:21 AM
Never can have too much lube on that shaft before insertion. :keke:
HAHAH!

pliot bushing should be looked at

In what regard?

username
09-28-2010, 09:47 AM
clips need to look like pic below. then you slide the fork under the clip. Clip keeps the fork up against those two posts on the TOB.

http://farm3.static.flickr.com/2634/3750623276_59646c0538.jpg?v=0

Spitfire_17
09-28-2010, 10:02 AM
clips need to look like pic below. then you slide the fork under the clip. Clip keeps the fork up against those two posts on the TOB.

yep^^^

And to all y'all posting he did it right, hah.. id go check all your TOB's... because its wrong.

here is another pic. you can tell were the fork goes by looking at the two "flat" spots with the clip under the fork. Hope that helps man. http://www.mysportscar.com/andy/FA/197.jpg

codyace
09-28-2010, 10:12 AM
yep^^^

And to all y'all posting he did it right, hah.. id go check all your TOB's... because its wrong.


http://www.codyace.com/albums/album34/z33tob_1.sized.jpg

That's how mine are (KA on left, and a Z33 TOB on the new S14 sleeve on the right). That's how they come out as OEM in all Nissan cars with standard transmissions. On the two ends of that spring, you want the curve to be against the FORK, not up away from it, with just the little end against it.

username
09-28-2010, 10:18 AM
Im just pointing out that in the pics he posted the fork is not up againt the tabs on the TOB. the clip is turned and the fork is just kinda sitting there

Spitfire_17
09-28-2010, 10:35 AM
http://www.codyace.com/albums/album34/z33tob_1.sized.jpg

That's how mine are (KA on left, and a Z33 TOB on the new S14 sleeve on the right). That's how they come out as OEM in all Nissan cars with standard transmissions. On the two ends of that spring, you want the curve to be against the FORK, not up away from it, with just the little end against it.

yep, i gotcha, im just using that pic as reference show that there are designated flat spots the fork should slid on too, with the clip in place like you said, you can clearly see in his pictures its not correct.

codyace
09-28-2010, 03:35 PM
Oh shit i'm retarded, I didn't even notice the sleeve being wrong hahahahaha

loooooooong weekend is still screwing with me

Spitfire_17
09-28-2010, 03:56 PM
Oh shit i'm retarded, I didn't even notice the sleeve being wrong hahahahaha

loooooooong weekend is still screwing with me

haha! yeah i hear ya man, its all good

StryfeS13
09-29-2010, 05:16 PM
:duh: FUCK.

Well, I put my tranny in, with the TOB installed all wrong like it was in the first pic(cause i didnt re check this thread), and my clutch wouldnt engage.

So I took it all back apart. Is this how it goes? Someone said the curved end should be on the fork...but it feels very loose like that. I can slide the clip right off. When the pointed ends are on the fork like spitfire posted, it seems much more sturdy.

http://i55.tinypic.com/6gfprn.jpg
http://i53.tinypic.com/sbsklu.jpg
http://i55.tinypic.com/30jgokp.jpg

Spitfire_17
09-29-2010, 09:50 PM
looks fine now man, the clip usually is the other way like you said. There might even be a little dent were that round side of the clip rests on the fork, i cant remember. But if its way loose and that way seems better, it might work that way also..

StryfeS13
09-30-2010, 01:04 AM
everything is fixed.

clutch works great.

thanks guys

Sideways_blksr20
11-14-2010, 02:02 AM
so wich is da correct way just did my clutch and it wont engage into gear

Sideways_blksr20
11-14-2010, 02:09 AM
god damn i haveto pull my trammy again fml

rps13_1990
11-14-2010, 09:48 PM
clips need to look like pic below. then you slide the fork under the clip. Clip keeps the fork up against those two posts on the TOB.

http://farm3.static.flickr.com/2634/3750623276_59646c0538.jpg?v=0

TOB should look the exact same as the pic then slide onto the fork from the right side first