17x10 +25 on front of 240sx?

[silviadrift87]

anyone know how well these will fit? i have 20 mill fenders for the front. just wondering if they will rub. like the look of the concave, the 17x9 +15 i was planning to get doesnt have any. rear is 17x10 +12

[JRex]

I'm running 17x10 +12 on the front with stock fenders. If you have coils you are going to need a small spacer for them to clear.

[Om1kron]

yes they will fit.

[i need tires]

Make the car fit the wheels, not the wheels fit the car!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[SUPERSTAR]

Make the car fit the wheels, not the wheels fit the car!!!!!!!!!!!!!!!!!!!!!!!!!!!!


I love you!!

[KoukiMonsta]

they will fit on my 240sx so give them to me

i have no clue if they will fit on your car considering i havent the slightest clue what year it is...

[silviadrift87]

Make the car fit the wheels, not the wheels fit the car!!!!!!!!!!!!!!!!!!!!!!!!!!!!

that is actually exactly what i was thinkin. i oredered 17x10 +12 all around and ill do what it takes to fit em but im sure they will

[shiftdrift]

well if it hits the coilover, a spacer would be a better idea than hacking up a nice coilover.....

[DJPimpFlex]

that is actually exactly what i was thinkin. i oredered 17x10 +12 all around and ill do what it takes to fit em but im sure they will

Ok let me settle this once and for all. I know when I was going with the same set up I searched and searched and found little to no help.

Yes they fit on the front of a S13 and S14. S14 is probably easier, but I did it on a S13 with a bunch of "massaging". I run KTS coilovers and 5zigen FN01r-C's. I fit them in the front without a spacer. I just made sure that the wheel runs through the spring. If I rotate the spring it will hit the wheel, but I set it and put the weight down on the suspension and its fine.

I had to hammer in about 4 different places to make them fit without any rubbing at full lock. I just hammered it out, rattle canned it and its been fine ever since. If I get motivated I'll take pics of exactly where I had to pound, but overall you just keep test driving it and checking where its rubbing.

[silviadrift87]

i have pbm coils and got fns to. i figured i might have to hammer a little but it will be fine

[DJPimpFlex]

i have pbm coils and got fns to. i figured i might have to hammer a little but it will be fine

Or a lot.. I had to beat the shit out of my fender wells to get it to work properly with good steering angle. I should also mention that my car isn't what a lot of people on here would consider "low".

[Marcus]

i have pbms also. i ran a 17x10+25 wheel with a 20mil spacer. the rim rubbed the spring with an 8mil spacer.

so, with no spacer and pbms. i garuntee you it will hit the coil. the rim probably wont even sit flat on the hub.
FIX::: space out your wheels a bit


if the problem is tire rub, then bang out your fenderwells.
but this depends on ride height and tire size.
are you dumped? fatty tires? crazy knuckles?

[DJPimpFlex]

Ah that's another thing. I've been running 225/45/17 or 215/45/17 in the front.

[fliprayzin240sx]

17x10 +25...no fucking way. No coilover out there is that skinny. From personal experience, even 17x10 +12 are hit or miss up front. All depends on the coilover. I had shitty MRs and I had to add 8mm spacers to clear the damn springs and collars. My Aragostas, I can fit 18x10 +18 and not rub on anything.

[brndck]

i ran 17x10 +18 f & r on my s13 with kts coilovers and zbrakes. hadta hammer the inner fenders and roll the outer fenders, but it cleared the coils no problem.

[eklips3]

in this case would a 45 profile tire rub ?

[brndck]

in this case would a 45 profile tire rub ?

depends on how low your car is.
and what car it is.
and what setup you have.
and what time of year it is.
and if you have a giraffe in the car or not.
and if you love jesus or not.