nickgbmx
02-15-2010, 12:42 AM
Contact Info
Name: Nick
Location: San Diego CA
Phone: 619-971-6726 (text is prefered)
Email: [email protected]
Price: $8000obo
Alright, after just about getting the car 100% i have decided to actually go through with it and part ways with my hatchback. The car is just about finished and will be a very competitive track car or beast street car when its done. Cage is a summit pre bent cage installed by ASC fabrications in Lakeside CA. The motor is freshly built with about 10 miles or so. The motor was assembled with all new parts, nothing used, by TB at TB motorworx in Lemon Grove CA. The car has about 3 passes on the dyno on C16 and we started running low on fuel so its just a basic tune to get it good enough to idle and it still made 275WHP. I think with Q16 and a capable tuner this motor is 290+WHP. For the price listed below there are a few things that will vary from the pics.
1)NO slicks or skinnies, it will have steelies on it
2)NO kirkey seats, it will have a integra LS driver seat but harness will be included
3) currently has ITR valve cover with no catch can
Just in engine/drivetrain there is about 13k invested not including labor or the price of the car. I would really prefer to trade for something of EQUAL VALUE that is streetable. At the top of my list would be S13, S2000, E30 or something along those lines, but email me with other potential trades. Like i said the car is very close to being done it just needs to be tuned and thats about it before any serious driving is done.
Motor
B18B1 Block
Darton Sleeves
ACL race bearings
Eagle 95mm crank
Eagle H beam rods
Arias 15:1 compression button head pistons
Cometic head gasket
P72 GSR head
Portflow port and polish
5 Angle valve job
Skunk2 Stage 3 pro series cams
Skunk2 oversized valves
Skunk2 pro series valve springs
Skunk2 pro series retainers
Supertech valve guides
ARP rod bolts
ARP head bolts
AEBS cam gears
Fluidamper pulley
ITR water pump
ITR oil pump
TWM 52mm ITBs modidied by Skunk2
RC engineering 440CC injectors
TWM FPR
AVID solid motor mounts
B16 transmission
KAAZ LSD
ACT Extreme clutch
ACT lightweight flywheel
RMF longtube header
AEM EMS ECU
ZEAL Function coilovers
ITR lower control arms
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020223.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020220.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020215.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020218.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020214.jpg
Name: Nick
Location: San Diego CA
Phone: 619-971-6726 (text is prefered)
Email: [email protected]
Price: $8000obo
Alright, after just about getting the car 100% i have decided to actually go through with it and part ways with my hatchback. The car is just about finished and will be a very competitive track car or beast street car when its done. Cage is a summit pre bent cage installed by ASC fabrications in Lakeside CA. The motor is freshly built with about 10 miles or so. The motor was assembled with all new parts, nothing used, by TB at TB motorworx in Lemon Grove CA. The car has about 3 passes on the dyno on C16 and we started running low on fuel so its just a basic tune to get it good enough to idle and it still made 275WHP. I think with Q16 and a capable tuner this motor is 290+WHP. For the price listed below there are a few things that will vary from the pics.
1)NO slicks or skinnies, it will have steelies on it
2)NO kirkey seats, it will have a integra LS driver seat but harness will be included
3) currently has ITR valve cover with no catch can
Just in engine/drivetrain there is about 13k invested not including labor or the price of the car. I would really prefer to trade for something of EQUAL VALUE that is streetable. At the top of my list would be S13, S2000, E30 or something along those lines, but email me with other potential trades. Like i said the car is very close to being done it just needs to be tuned and thats about it before any serious driving is done.
Motor
B18B1 Block
Darton Sleeves
ACL race bearings
Eagle 95mm crank
Eagle H beam rods
Arias 15:1 compression button head pistons
Cometic head gasket
P72 GSR head
Portflow port and polish
5 Angle valve job
Skunk2 Stage 3 pro series cams
Skunk2 oversized valves
Skunk2 pro series valve springs
Skunk2 pro series retainers
Supertech valve guides
ARP rod bolts
ARP head bolts
AEBS cam gears
Fluidamper pulley
ITR water pump
ITR oil pump
TWM 52mm ITBs modidied by Skunk2
RC engineering 440CC injectors
TWM FPR
AVID solid motor mounts
B16 transmission
KAAZ LSD
ACT Extreme clutch
ACT lightweight flywheel
RMF longtube header
AEM EMS ECU
ZEAL Function coilovers
ITR lower control arms
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020223.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020220.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020215.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020218.jpg
http://i226.photobucket.com/albums/dd147/allmotor1313/PA020214.jpg