Bomb ass KA or RB Clutches and KA Knock Sensor

[nosajton]

trying to clean out the garage round two so heres some stuff i've been holding on to

rb20det/KA24 JWT clutch with exedy chromoly 13lb lightened flywheel
this clutch definately will hold almost any power you can throw at it, i was running 650whp / 548wtq on this clutch without any slippage.. jwt rates it to 600wtq but that is conservative im sure.. this clutch only has 3000miles on it so it's got plenty of life left.. got a little bit of surface rust on flywheel because its been sitting a few months but in overall good condition

only reason im selling it is because i switched to auto tranny for the drag car so my loss is your gain.. bought it new for $450 (clutch) and $350 (flywheel) asking $450 shipped OBO

http://i588.photobucket.com/albums/ss324/crazys14/clutch.jpg
http://i588.photobucket.com/albums/ss324/crazys14/clutch2-1.jpg
http://i588.photobucket.com/albums/ss324/crazys14/clutch3.jpg
http://i588.photobucket.com/albums/ss324/crazys14/clutch4.jpg


This is a JWT RB20/KA24 pressure plate/clutch disc the pp has minor surface rust but is definately still in spec and clutch disc has 3.70mm of meat left on it so thats about 15k miles (bought new for $450) asking $150 shipped OBO
http://i588.photobucket.com/albums/ss324/crazys14/clutch2-1-1.jpg
http://i588.photobucket.com/albums/ss324/crazys14/clutch2-2.jpg

KA24DE knock sensor $35 shipped
http://i588.photobucket.com/albums/ss324/crazys14/knock.jpg

[NotoriouS14]

were r u located in socal?..ill pick up the knock sensor..lmk

[SUPERSTAR]

This is false advertising. Tittle clearly states, Bomb Ass. All I see is parts.

[nosajton]

were r u located in socal?..ill pick up the knock sensor..lmk

in san diego

[nosajton]

This is false advertising. Tittle clearly states, Bomb Ass. All I see is parts.

very funny

[nosajton]

first bump

[Nismo240z]

take better pictures of the pressure plate/clutch plate, I'm intersted

[nosajton]

first bump

[roboticnissan]

wait the clutch fits an rb and a ka?? i dont think thats right is it??

[IThaJokaI]

wait the clutch fits an rb and a ka?? i dont think thats right is it??

RB20, KA24e/de and CA18 all use the same input shaft on the trans, and all of the bolt patterns on the cranks are the same. In common terms, all 4clutches will work, as long as you use the right flywheel.

I had a ka24e (truck flywheel) with a rb20 stage 3 clutch on my last KA.

[nosajton]

wait the clutch fits an rb and a ka?? i dont think thats right is it??

yeah this combo is a rb20 clutch which is 250mm and uses a 350z clutch which is 250mm.. the stock 240 ka clutch is 225mm which is weak.. extra 25mm does not sound like a lot of surface space but it really is since it is towards the outside of the flywheel.. like i said this is rated to handle atleast 600ft lbs of torque which should be plenty for the majority of setups

you can also run it on a rb just fine

[BTP]

bombass parts dude.LOL

[nosajton]

thanks!


second bump

[racerx2k1]

first bump

first bump

thanks!


second bump

2 bump limit. You can start new thread in 3 days.