S&W Racing Weld in Roll Cages - GREAT Price !!!

[Enjuku Racing]

Hey guys this is Kevin From Enjuku Racing. As promised here is the group buy!

I was actually able to take $75.00 off of the all ready low priced S&W Roll Cages. Just because We want to help you guys out the best we can. We arnt out here to take everyone of your hard earned dollars that you will need for more tires! Instead we are out here trying our best to give you all Great deals on parts to keep the sport alive!! So here it is!!!!!!!!

Contact: Kevin Lawrence
Phone: 352 241 8399
Email: [email protected]
Price: Price's listed!

Ok guys, Ive been working with S&W Racecars about getting a Group Buy going for 8 point & 10 point roll cage's.

Here's the way it will go down.

We need at least 15 People to get it done. Or it wont happen...

I will need All of your information (name, address, CC numbers) to get your name on the list. Once the list gets to 15 People then I will charge the card for the Amount of the cage and shipping. Depending what shipping option you will need.

Here are the cage's that I have listed for the group buy.

Note: (If you have a different car not listed Please email me for availability for your application)
[email protected]


The cage's I list are Formula D rule book required material. Im sure you will need to modify the Door bar if you plan to run this cage in a FD car tho! But it is a great starting point at a great price!

S13 Drift Car Roll Cage - 11-5594DC $524.95
89-94 Nissan 240SX Roll Cage for Drift Car racing. 1 3/4" X 0.120 DOM M/ild steel
MAIN HOOP & ROOF HOOP ARE WIDER THAN STANDARD CAGE
INTERIOR PANELS MUST BE REMOVED
WINDSHIELD RUNNERS FIT BETWEEN DASH AND DOOR
CAGE INCLUDES DIAGONAL & 2-PIECE CROSSMEMBER FOR MAIN HOOP
AND REAR STRUT TOWER CROSSMEMBER

S13 10 Point Roll Cage - 11-5594TD-DOM $424.95
89-95 Nissan 240SX, thru Dash, 1-3/4 x .120" wall DOM tubing

S13 8 Point Roll Bar - 11-5094-DOM $324.95
89-95 Nissan 240SX, 1-3/4 X .120" wall DOM tubing

S14 10 Point Roll Cage - 11-5597TD-DOM $425.95
95-98 Nissan 240SX, through dash, 1-3/4 x .120" wall DOM tubing

S14 8 Point Roll Bar - 11-5097-DOM $324.95
95-98 Nissan 240SX, 1-3/4 x .120" wall DOM tubing

AE86 10 Point Roll Cage - 11-5548TD-DOM $424.95
84-87 Toyota Corolla, thru Dash, 1-3/4 x .120" wall DOM tubing

AE86 8 Point Roll Bar - 11-5048-DOM $324.95
84-87 Toyota Corolla, 1-3/4 X .120" wall DOM tubing

FC 10 Point Roll Cage - 11-5566-DOM $424.95
86-91 Mazda RX7, 1-3/4 x .120" wall DOM tubing

FC 8 Point Roll Bar - 11-5066-DOM $324.95
86-91 Mazda RX7, 1-3/4 X .120" wall DOM tubing



Ok now for shipping arrangements. If you are local and want to come pickup your cage from our Shop the inbound shipping will be cheaper than shipping it to your house because I will have multiple Cage's freighted here (Need atleast 5)!! Price for shop pickup is.$xx If you are not local and need your cage shipped to you the price will be $110 Flat rate anywhere in the Lower 48states. (no PR, Canada, HI, AK)

NOTE!! I AM WAITING ON A REPLY FOR THE QUOTE FOR FREIGHTING THE CAGE'S TO OUR SHOP.
I WILL UPDATE WITH THAT PRICE WHEN AVAILABLE!!!


So lets get some names on this list other than my self and get some cages!!!!

If you have any questions at all Please Email me [email protected]

Here is just some basic pics for you guys to get an idea of what 8point vs 10points will be.

10 Point
http://img.photobucket.com/albums/v251/boobakup/CAGEnewHC.jpg


8 Point
http://img.photobucket.com/albums/v251/boobakup/ROLLBAR.jpg

[FerretsCanDrift]

Sick prices!!

[longdy]

are these bolt on?

[SoSideways]

are these bolt on?

Can you read?

Says weld in DUDEBRO.

[Flicktitty]

do you have a pic of the 8pt installed? i wanna see how high the door bars are.

[Enjuku Racing]

Here are a few links i found on google

[email protected] race cars 10pt roll cage/ getting ready for d1 usa in 2009!!: 240SX Forum / 180SX Forum / Silvia Forum: Nissan Forums / Infiniti Forums - NICOclub (http://forums.nicoclub.com/zerothread/383280-sw-race-cars-10pt-roll-cage-getting-ready-for-d1-usa-in-2009)

http://zilvia.net/f/tech-talk/176132-s-w-roll-cages-any-info-will-help.html

Thanks

Ken

[Slidin240Wayz]

Are you serious?

http://a305.ac-images.myspacecdn.com/images01/67/l_7322a049a1838451d6f681810cf2a028.jpg

[Enjuku Racing]

Are you serious?

http://a305.ac-images.myspacecdn.com/images01/67/l_7322a049a1838451d6f681810cf2a028.jpg



I don't belive that is a spec S&W cage. That cage has a ton of stuff added to it.

Ken

[bejota180sx]

kevin, i was wondering if i could ask for a cage but somewhat custom...

im interested in this cage but i do not want the bar under the dash nor the door bars... practically i just want a six point... with that bar in the main hoob to use as a harness bar...

any info on this?

thanks! btw im guessing this comes dissasembled? and i would weld it on my own right?

[Enjuku Racing]

The best way to reach Kevin is to shoot him an email - [email protected]

yes, they come unassembled.

He is the one taking care of all of this group buy

thanks
Ken

[Enjuku Racing]

We are waiting for S&W do send us some more details on exactly everything on the 240sx cages. We will post more as we get it.

This is an awesome deal.. dont miss out. ... email - [email protected] with any questions.

thanks

ken

[longdy]

Can you read?

Says weld in DUDEBRO.

what i really wanted to say was could they be bolted in instead???..lol my bad

[Black Guy]

kevin, i was wondering if i could ask for a cage but somewhat custom...

im interested in this cage but i do not want the bar under the dash nor the door bars... practically i just want a six point... with that bar in the main hoob to use as a harness bar...

any info on this?

thanks! btw im guessing this comes dissasembled? and i would weld it on my own right?

Thats almost like an 8point

[¹²³Klan™]

price shipped to 91755 for:

S14 10 Point Roll Cage - 11-5597TD-DOM $425.95
95-98 Nissan 240SX, through dash, 1-3/4 x .120" wall DOM tubing

S14 8 Point Roll Bar - 11-5097-DOM $324.95
95-98 Nissan 240SX, 1-3/4 x .120" wall DOM tubing


seperate pricing please.
shipping to a residential.

[SoSideways]

Im VERY interested, so basically its just piping? and we weld it together?

how is fitment?

any through dash?

can you get more pictures of s14?

Everything you asked have already been answered.

Good lord.

[Jonnie Fraz]

Im VERY interested, so basically its just piping? and we weld it together?

Tubing...not pipe. Sorry there is a massive difference between dom tubing and pipe.
My guess it is all the tube bent to fit your car and then yes you weld it together in your chassis.
Also this is an unbelievable price for a weld in cage. Tubing for a cage can exceed this price guys, not including all the work that goes into the bends.
A quick question... Where the tubes join are they coped already or would this need to be done on site?

Thanks

[zaquanh]

are these in d1 spec?

[Enjuku Racing]

^ I would say The Drift Spec Cage for S13 should be able to pass tech. But I dont have a D1 Rule book to look up the spec's for their requirements. With all the cage's I listed tho are greater than the requirements for Formula D in Tube sizing, and Wall thickness. Like stated in the main Description, you will most likely have to modify the door bar into a X shape to meet requirements for Formula D/ D1.

C'mon guys lets get this going!!

[email protected]

[Enjuku Racing]

price shipped to 91755 for:

S14 10 Point Roll Cage - 11-5597TD-DOM $425.95
95-98 Nissan 240SX, through dash, 1-3/4 x .120" wall DOM tubing

S14 8 Point Roll Bar - 11-5097-DOM $324.95
95-98 Nissan 240SX, 1-3/4 x .120" wall DOM tubing


seperate pricing please.
shipping to a residential.

Shipping is posted in the First post. It is $110 Flat Rate for any cage listed if purchased under this group buy.

Im sure you will ask why? as the 8 points are lighter than the Heavier 10 points. here is the answer.

It actually will cost more for either one shipped to that zip. We will most likely loose a few bux shipping them at that price to you. But I posted that price to help out everyone get in on this great deal!! Im not here posting this group buy to try and take every last dollar you have. But rather to help you all get a cage's in your cars so you guys can start getting into local competitions / events and be safe!

So lets get this going!!

-Kevin

[zaquanh]

would you say they meet these requirments?

i know its alot but with d1gp coming up im sure people will ask , and for the price , thats a great price , and if its in d1 spec you will be having to add me to the list



Main Hoop
The main roll cage hoop shall be as wide as the full width of the interior and must be as close to
the roof as possible. One continuous length of roll bar tubing shall be used as the main hoop.
The main hoop must consist of not more than four (4) bends maximum, totaling one hundred
eighty (180) degrees +/- ten (10) degrees.

Diagonal Brace
At least one (1) diagonal brace shall be used in the same plane as the main hoop. One end of
the diagonal brace shall attach to the corner, or horizontal part, of the main hoop above the
driver’s head, within twelve (12) inches of the driver’s-side corner. The other end of the diagonal
brace shall attach to the mounting plate (or to the main hoop as close to the mounting plate as
practically possible) diagonally opposed to the driver’s head (passenger floor).

Forward Hoops - Option 1
The forward hoops shall extend from the main hoop (in a forward direction) to the floor by
following the roof and the “A” pillar of the car. There shall be a bar connecting the two (2)
forward hoops at the top of the windshield mounted as close to the roof as possible. The
forward hoops shall incorporate no more than four bends each. Optionally a Halo Hoop (Option
2)” or Front Hoop (Option 3)” construction may also be acceptable.

Halo Hoop (Option 2)
A “halo bar” extends from the main hoop (in a forward direction) following the roof line to the
windshield then following along the top of the windshield, then following the roof line back to the
main hoop, thus creating a “halo” over the driver’s head. A “halo” bar shall be constructed of one
continuous piece of tubing. One (1) down tube following the “A” pillar must support the “halo” on
each side of the car. The down tubes shall incorporate no more than two (2) bends each.

Front Hoop (Option 3)
\A “front hoop” is a bar that extends up from the floor, then follows the “A” pillar up to the roof,
then follows the roof line across the top of the windshield, then back down the other “A” pillar,
and then terminates on the floor. There must be one (1) horizontal bar (following the roof line)
connecting the main hoop and the forward hoop on each side of the car. The front hoop shall
incorporate no more than four (4) bends.

Rear Brace
The main hoop must have two (2) brace extending to the rear. The brace shall be attached as
near as possible to the top of the main hoop, and no more than six (6) inches below the top.
Rear brace must not contain any bends

The main hoop brace may be mounted at the rear shock mounts or suspension pickup points.
They may go through any rear bulkheads provided the bulkhead is sealed around the cage
brace.

Door Bars / Side Impact Protection
Door bars on both driver and passenger side must be used. The driver’s door window glass,
window operating mechanism, armrest, map pockets, door panel, and inside door latch may be
removed. *This gutting of the door is only permitted if the roll cage incorporates at least two (2)
NASCAR style door bars that extend into the door or an X brace.

Mounting Points
The roll cage shall be mounted to the floor of the car in a minimum of six points. The cage shall
not go through the firewall. The seventh and eighth points must attach to the firewall or front
fender wells. All cage attachment points must be mounted to plates.

Mounting Plates
Each mounting plate shall be no greater than 100 square inches and no greater than 12 inches
or less than 2 inches on a side. Welded mounting plates shall be at least 0.080 inch thick.
Plates may extend onto vertical sections of the structure. Any mounting plate may be multiangled,
but shall not exceed 100 square inches total including vertical sections.

Mounting Plates – Bolt-In Cage
The attaching points of a bolt-in cage to the body must use reinforcing plates to sandwich the
body. At least three (3) bolts are required for each bolt-in plate and the plate must be at least
3/16 inch thick. All hardware must be SAE Grade 5 or better with 5/16” diameter minimum.


Tube / Mounting Plate Specifications
Any number of tubes may attach to a plate so long as they are touching each other at the plate.
There may be a small gap between tubes to allow welding 360 degrees around each tube

Tubing Sizes
Driver safety is of paramount importance below are the minimum requirements, it is always
better to over build the safety cage. Minimum1.5” OD x 0.095 DOM Steel 1.5” OD x 0.083
Chromium Molybdenum Steel

[¹²³Klan™]

add me to the list, when is payment needed?

[SR2Zero]

I threw an email Kevins way... Waiting on response.. I hope to hop in on this one! Great Pricing!

[C. Anderson]

I have been looking at these for some time now and wish I was ready to spring for one. This might help anyone wanting specs. This is for the s13 drift cage, it's the only one I have.
http://i101.photobucket.com/albums/m53/95silvia06/DriftCage.jpg

[zolika]

Can they make s14 Drift Car Roll Cage ?

[zaquanh]

Can they make s14 Drift Car Roll Cage ?


read first post

[ZenkiCam]

I have been looking at these for some time now and wish I was ready to spring for one. This might help anyone wanting specs. This is for the s13 drift cage, it's the only one I have.
http://i101.photobucket.com/albums/m53/95silvia06/DriftCage.jpg

holy god damn, my picture spread like wild fire quickly... i just posted it today, on another forum. did you find it on 240atlanta?

[AznDrftr.]

im in on this for sure.

[C. Anderson]

holy god damn, my picture spread like wild fire quickly... i just posted it today, on another forum. did you find it on 240atlanta?

I can't remember, I found it a couple months ago.

[SR2Zero]

I think I'm in also, just gotta decide either 8 point or 10... Hmm..

[energ]

price on 10 point s13 cage shipped to a business in 60118

S13 10 Point Roll Cage - 11-5594TD-DOM $424.95
89-95 Nissan 240SX, thru Dash, 1-3/4 x .120" wall DOM tubing

[Black Guy]

price on 10 point s13 cage shipped to a business in 60118

S13 10 Point Roll Cage - 11-5594TD-DOM $424.95
89-95 Nissan 240SX, thru Dash, 1-3/4 x .120" wall DOM tubing

15 people by the end of next week shipping will be roughly 40 bucks a cage, any later its like 110 a cage. Lets jump on this guys!

[Enjuku Racing]

^ your a lil bit off.

If I get the order before the end of next week all of the cage's comming inbound to our shop will be the $40 Cost. But any cage that will be shipping anywhere but our shop, Will be a flat rate of $110 weather its a 8 or 10 point.


if we dont get the group buy going before the end of next week the $40 inbound charge for people who are gona pickup their cage from our shop. Will Rise. This was just a shipping special that SW was running for these 2 weeks.

Email me to get on the list!!

-Kevin

[Enjuku Racing]

Come on guys Need more people!!

List updated!


1. Enjuku Racing - S13 10 Point Drift cage (this one we are going to order just for stock)
2. Me - AE86 10 Point
3. Black Guy - ??? 10 point
4. Joe Grande - S14 8 Point

Email me your info so we can get this going!!!
[email protected]

Thanks,
Kevin

[Enjuku Racing]

Come on guys Need more people!!

List updated!


1. Enjuku Racing - S13 10 Point Drift cage (this one we are going to order just for stock)
2. Me - AE86 10 Point
3. Black Guy - ??? 10 point
4. Joe Grande - S14 8 Point
5. Jeremy Bowers - 4th Gen Fbody 8 point
6. Nate Barkman - S13 EWS 10 Point
7. B Rad - 3rd Gen Fbody 8 point
8. Robert Hogan - S13 8 Point


Email me your info so we can get this going!!!
[email protected]

Thanks,
Kevin

[AznDrftr.]

Lets go people, lets get some more people on this, helluva deal here.

[3vilmonkey!]

Hmmm.. I might be interested... s14 10pt

[Enjuku Racing]

^ Please email me. I am almost done with the list and will begin collecting payment shortly.

[email protected]

-Kevin

[JDMtyteYO!]

wooo number 6 is me!! expect going with the DOM tubing :) cant wait to get this!

[93superHICAS]

so how much is shipping,
on a 10 point insted of the bars going down to the lower front bars (for the door bars) could you just make "x" door bars or would i have to get somebody to do that.?
or do you have an option of that?
its for a s13 hatch

[AznDrftr.]

so how much is shipping,
on a 10 point insted of the bars going down to the lower front bars (for the door bars) could you just make "x" door bars or would i have to get somebody to do that.?
or do you have an option of that?
its for a s13 hatch

Shipping is $110.00

[tracksuitslava]

very interested in 8pt for fc, any pics of it? and does it come with door bars?

[Enjuku Racing]

Sorry for the late reply guys.

group buy is finished.


thanks to all those who participated!!!!

-Kevin

[drifter_for_life06]

ive been to the S&W shop, seen lots of their cages in lots of different cars....top notch cages at a GREAT price

[ESone3]

For all that missed out, you suck.

Just got mine today, shit it on point! I didn't expect notched so that was an added bonus. Thanks Enjuju for setting this up.

[smellslikecurry]

sweet i cant wait to get mine in

which setup did you get and can you take some pics?