PDA

View Full Version : CA FS: HALTECH E6X Full Stand Alone w/LS1 Coils - Wired For SR20DET


RMJmotor
02-01-2009, 10:48 PM
Guys I have the full Haltech E6X setup off my old Pro AM Drift 240sx starting to part the car out as the car did not sell as a whole.

*** I Accept Cash and Paypal. I will ship, AT BUYER EXPENSE. ***

This is a Full stand alone unit and will need to be reprogramed for your Sr20DET setup.

$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**

This setup is complete, pre-wired for the SR20DET Redtop. Includes the following:

- Haltech E6X stand alone ECU
- Full flying lead Harness pre-wired for SR20DET redtop w/ side feed injectors. Will fit stock TPS/ temp / Cam sensors
- LS1 Coils (This will not work with stock SR20 Coils unless re-wire) LS1 coils are much stronger than the stock coils.
- Custom made 8.5mm Magnacor spark plug wires. Made for LS1 to Sr20 Plugs
- 3-bar Map sensor
- Haltech Fuse block
- Air intake temp sensor

http://c3.ac-images.myspacecdn.com/images02/35/l_48a10fc2e3b44b8d8a2a491e5079db16.jpg

http://c3.ac-images.myspacecdn.com/images02/24/l_da6bb6c7cfc1490bb8251177ba6cb96a.jpg

This is the Haltech installed in he car:

http://c1.ac-images.myspacecdn.com/images02/9/l_e80c64f445224e18b510f088587fda78.jpg

Basically just ditch you old harness and ECU, run the new harness, run power and ground to ECU and Fuel pump. Plug in the injectors, coils and sensors, program, and go.

I will ship, Retail on this ECU is over 1300.00 and that does not include having the harness made and wired or installation, LS1 coils new are about 200 and you need to wire and make the cables.

$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**


Contact me with any Questions.

mikez97
02-01-2009, 10:50 PM
will it work in a s14 sr

RMJmotor
02-01-2009, 10:54 PM
Yes the ECU will controll it, but you might have to wire in the S14 cam position sensor and the temp and TPS sensors. I have the redtop connectors wired into the harness

mikez97
02-01-2009, 10:57 PM
do you take a CC?

RMJmotor
02-02-2009, 08:41 AM
Mike97: sent you a Private Message

SR20PWRALTY
02-02-2009, 03:19 PM
Hey what will I need to change to make this work for bluebird sr20? I know for sure that I can't use coil packs or can I convert? sorry kinda new on the whole stand alone system.

RMJmotor
02-02-2009, 04:32 PM
You can use the LS1 coils, that is controlled by the stand alone and will simply need to be program. These coils are more than twice as strong and capable than the stock.

Only difference I can think of its the plugs for the stock Cam position sensor, temp sensor, TPS, and possible fuel injectors (if not side fed) would need to be re-wired for the connectors on the blubirds sensors.

Map sensor plug, air intake, ls1 coils would all remain the same.

This harness was build in my s13 240sx so the wiring may not be the right length, but should not be a big issue.

SR20PWRALTY
02-04-2009, 09:30 PM
Thanks for clearing that up will look into it. Go deal for it being pre wired for s13

240love
02-04-2009, 10:26 PM
legit seller right here!!

RMJmotor
02-05-2009, 08:56 AM
Bumping it - Right befor the Weekend.

thenephilm
02-05-2009, 09:49 AM
thats a pretty nice deal...wish i had my tax return :(

RMJmotor
02-06-2009, 03:53 PM
Last BUMP for the weekend. THis is a smoking deal

SRKOUKIMONSTA
02-06-2009, 03:58 PM
Sick!!!!!!!!!!!!!!