TneChosenOne
12-24-2008, 01:32 PM
Ok here is the bad the motor is blown. It still runs and drives but the 4th piston or bearing is shot. I got this car thinking it would be a quick fix and swapped out the motor for an s13 one and it lasted about a week. The rear trunk is rusted slightly and has been stripped and sprayed but it keeps coming thru.the wheels need refinishing. The speed sensor and other tranny sensors need to be hooked up. the radio mount needs to purchased.
The good: F1spec seats. The wheels are 3 piece, the rear tires are new the front have 75 percent tread left. It has a full 3 inch exhaust with test pipe. It has another short block getting machined right now for supertech low compression pistons(yes they come with the car) and i also have a full timing kit for it. It has eibach springs in the front and the rears have yet to be installed. I have 30mm and 26 mm 300zx calipers and 30mm drilled and slotted rotors for all 4 corners and agency power lines for the front and rear but one of the rears is being used as a clutch line. Stainless headers. Lc1 wideband.
As far as trades go i want an s13 coupe prefer black or white. If you have something you think is worth more or not still make an offer. I also like 2.5rs subarus, mr2 toyotas and alot of other mid to early 90's cars
buddy club seat rail
http://i186.photobucket.com/albums/x272/thattru1/IMG00194.jpg
F1spec front seats only have one rail
http://i186.photobucket.com/albums/x272/thattru1/IMG00223.jpg
copper heat sheild made at work
http://i186.photobucket.com/albums/x272/thattru1/IMG00217.jpg
18x9.5 in rear 18x8.5 in front aldstadt wheels
http://i186.photobucket.com/albums/x272/thattru1/IMG00218.jpg
generic ebay headers and innovative lc1
http://i186.photobucket.com/albums/x272/thattru1/IMG00218.jpg
lightly rusted rear trunk due to having a spoiler before i got it
http://i186.photobucket.com/albums/x272/thattru1/IMG00226.jpg
slight dent in front driver fender
http://i186.photobucket.com/albums/x272/thattru1/IMG00225.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00165.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00220.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00221.jpg
wheels need refinishing. One has been machined
http://i186.photobucket.com/albums/x272/thattru1/IMG00228.jpg
This is also over at nico
The good: F1spec seats. The wheels are 3 piece, the rear tires are new the front have 75 percent tread left. It has a full 3 inch exhaust with test pipe. It has another short block getting machined right now for supertech low compression pistons(yes they come with the car) and i also have a full timing kit for it. It has eibach springs in the front and the rears have yet to be installed. I have 30mm and 26 mm 300zx calipers and 30mm drilled and slotted rotors for all 4 corners and agency power lines for the front and rear but one of the rears is being used as a clutch line. Stainless headers. Lc1 wideband.
As far as trades go i want an s13 coupe prefer black or white. If you have something you think is worth more or not still make an offer. I also like 2.5rs subarus, mr2 toyotas and alot of other mid to early 90's cars
buddy club seat rail
http://i186.photobucket.com/albums/x272/thattru1/IMG00194.jpg
F1spec front seats only have one rail
http://i186.photobucket.com/albums/x272/thattru1/IMG00223.jpg
copper heat sheild made at work
http://i186.photobucket.com/albums/x272/thattru1/IMG00217.jpg
18x9.5 in rear 18x8.5 in front aldstadt wheels
http://i186.photobucket.com/albums/x272/thattru1/IMG00218.jpg
generic ebay headers and innovative lc1
http://i186.photobucket.com/albums/x272/thattru1/IMG00218.jpg
lightly rusted rear trunk due to having a spoiler before i got it
http://i186.photobucket.com/albums/x272/thattru1/IMG00226.jpg
slight dent in front driver fender
http://i186.photobucket.com/albums/x272/thattru1/IMG00225.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00165.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00220.jpg
http://i186.photobucket.com/albums/x272/thattru1/IMG00221.jpg
wheels need refinishing. One has been machined
http://i186.photobucket.com/albums/x272/thattru1/IMG00228.jpg
This is also over at nico