lutz5329
11-23-2008, 08:13 PM
I have tons of parts laying around my garage and I need to clean up.
I have a fully built SR20det that has all the goodies. I'll try to list it all. for the bottom end it has.
$500 CP pistons 8.5-1,86.5mm
$350 Eagle rods H beam
$200 Unorthodox Racing Crank Pulley
$200 Gasket Kit
$50 New Water pump
$1125 bottom end work
Bearings
Machine work
Engine cryogenics
For the top end I have
1. $75 Greddy rocker arm stoppers
2. $300 HKS adjustable cam gears
3. $250 HKS valve springs
4. $230 ARP head studs & Cometic HG 86.5mm +.040
5. $430 Top End Work
a. Machine work
b. 3 angle valve job
c. Cryogenics
The reason the engine has stock cams is because I got screwed from a guy on here. I bought an engine from him and he said everything was fine but it wasn't. I have a set of HKS step 2 272 cams that I'm not sure but I believe they are unusable. They have gouges in the journals where they sit in the head. I wish I could use them but I can't. I will include the cams with the engine if the buyer wants them. Also don't worry because I didnt use the same head that I got the cams in I had another engine that I was building I just took the parts that I could use off that engine and put it on mine. Not trying to hide anything. I also have the extra head that the cams were in but I'm not sure if its usable either
I also have 5 speed Tansmission fadanza flywheel and exedy stage 1 clutch
I want to sell the engine as a hole. I have everything for the swap ecu, maf, harness, etc. The harness is a mess I was going to have it professionally done.
Its basicly brand new. Never been turned over
I dont have the turbo side (manifold or turbo). That was the next step but I ran out of money.
I want $3,500 for everything: pictures below. I can always take more upon request.
http://photos.freshalloy.com/gallery/d/42006-2/DSCN1475.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1475.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/42003-2/DSCN1473.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1473.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/42000-2/DSCN1469.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1469.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/39406-2/DSCN1270.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1270.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/39403-2/DSCN1269.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1269.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/41997-2/DSCN1260.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1260.JPG.html?g2_navId=x7fa2aabe)
Besides the engine I have tons of other parts sitting around my garage. I'll try to list them all.
Every price is with shipping NOT included
Extra Head (with damage) $80 also could package it with my extra springs,valves, etc.
http://photos.freshalloy.com/gallery/d/42010-2/DSCN1455.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1455.JPG.html)
http://photos.freshalloy.com/gallery/d/42013-2/DSCN1458.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1458.JPG.html)
http://photos.freshalloy.com/gallery/d/42016-2/DSCN1459.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1459.JPG.html)
Engine mounts $20
Megan elbow and down pipe $200
http://photos.freshalloy.com/gallery/d/34901-2/DSCN1167.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1167.JPG.html?g2_navId=x7fa2aabe)
New OEM redtop SR20det Head gasket $40
http://photos.freshalloy.com/gallery/d/36140-2/DSCN1186.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1186.JPG.html?g2_navId=x7fa2aabe)
New Thrust bearings $15
VLSD with 5 bolt: includes shafts $315
http://photos.freshalloy.com/gallery/d/34847-2/DSCN1147.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1147.JPG.html?g2_navId=x7fa2aabe)
DOHC Powersteeing lines for s13 good condition $150
FMIC if it doesn't go with the engine $100 (4 couplers but no clamps) also up pipes are turned around in the pic
http://photos.freshalloy.com/gallery/d/34844-2/DSCN1148.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1148.JPG.html?g2_navId=x7fa2aabe)
SR20det stock flywheel $30
http://photos.freshalloy.com/gallery/d/34853-2/DSCN1150.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1150.JPG.html?g2_navId=x7fa2aabe)
Stock SR20det elbow
http://photos.freshalloy.com/gallery/d/34862-2/DSCN1154.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1154.JPG.html?g2_navId=x7fa2aabe)
S14 radiator $100 (includes i believe it is the ac fan)
http://photos.freshalloy.com/gallery/d/34898-2/DSCN1166.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1166.JPG.html?g2_navId=x7fa2aabe)
s13 radiator stock
http://photos.freshalloy.com/gallery/d/34865-2/DSCN1160.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1160.JPG.html?g2_navId=x2989bc0f)
stock SR20det valvetrain.. Its all been cryogenicly treated and is in working condition. I believe I have two sets of (springs, valves) 1 set of retainers.
all together srpings, valves and retainers $50
Alternator for SR20det redtop $50
-----------------------------------------------------------------------------
Some KA SOHC parts
AC condencer and core $100
http://photos.freshalloy.com/gallery/d/34835-2/DSCN1078.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1078.JPG.html?g2_navId=x2989bc0f)
http://photos.freshalloy.com/gallery/d/34838-2/DSCN1075.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1075.JPG.html?g2_navId=x2989bc0f)
throttle body $40
http://photos.freshalloy.com/gallery/d/34868-2/DSCN1156.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1156.JPG.html?g2_navId=x2989bc0f)
Fan shroud for KA $30
http://photos.freshalloy.com/gallery/d/34874-2/DSCN1155.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1155.JPG.html?g2_navId=x2989bc0f)
ECU stock $40
stock MAF sensor $30
http://photos.freshalloy.com/gallery/d/34889-2/DSCN1163.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1163.JPG.html?g2_navId=x2989bc0f)
s13 automatic trans brace $10
alternator (not %100 it works) $30
ALL prices are OBO so if you need any of this stuff feel free to make some offers.
Like always I probably forgot some parts so ask and I'll let you know if I have what you need.
Thanks for looking. have a good one
PM offers or if you have any question
I have a fully built SR20det that has all the goodies. I'll try to list it all. for the bottom end it has.
$500 CP pistons 8.5-1,86.5mm
$350 Eagle rods H beam
$200 Unorthodox Racing Crank Pulley
$200 Gasket Kit
$50 New Water pump
$1125 bottom end work
Bearings
Machine work
Engine cryogenics
For the top end I have
1. $75 Greddy rocker arm stoppers
2. $300 HKS adjustable cam gears
3. $250 HKS valve springs
4. $230 ARP head studs & Cometic HG 86.5mm +.040
5. $430 Top End Work
a. Machine work
b. 3 angle valve job
c. Cryogenics
The reason the engine has stock cams is because I got screwed from a guy on here. I bought an engine from him and he said everything was fine but it wasn't. I have a set of HKS step 2 272 cams that I'm not sure but I believe they are unusable. They have gouges in the journals where they sit in the head. I wish I could use them but I can't. I will include the cams with the engine if the buyer wants them. Also don't worry because I didnt use the same head that I got the cams in I had another engine that I was building I just took the parts that I could use off that engine and put it on mine. Not trying to hide anything. I also have the extra head that the cams were in but I'm not sure if its usable either
I also have 5 speed Tansmission fadanza flywheel and exedy stage 1 clutch
I want to sell the engine as a hole. I have everything for the swap ecu, maf, harness, etc. The harness is a mess I was going to have it professionally done.
Its basicly brand new. Never been turned over
I dont have the turbo side (manifold or turbo). That was the next step but I ran out of money.
I want $3,500 for everything: pictures below. I can always take more upon request.
http://photos.freshalloy.com/gallery/d/42006-2/DSCN1475.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1475.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/42003-2/DSCN1473.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1473.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/42000-2/DSCN1469.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1469.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/39406-2/DSCN1270.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1270.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/39403-2/DSCN1269.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1269.JPG.html?g2_navId=x7fa2aabe)
http://photos.freshalloy.com/gallery/d/41997-2/DSCN1260.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1260.JPG.html?g2_navId=x7fa2aabe)
Besides the engine I have tons of other parts sitting around my garage. I'll try to list them all.
Every price is with shipping NOT included
Extra Head (with damage) $80 also could package it with my extra springs,valves, etc.
http://photos.freshalloy.com/gallery/d/42010-2/DSCN1455.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1455.JPG.html)
http://photos.freshalloy.com/gallery/d/42013-2/DSCN1458.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1458.JPG.html)
http://photos.freshalloy.com/gallery/d/42016-2/DSCN1459.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1459.JPG.html)
Engine mounts $20
Megan elbow and down pipe $200
http://photos.freshalloy.com/gallery/d/34901-2/DSCN1167.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1167.JPG.html?g2_navId=x7fa2aabe)
New OEM redtop SR20det Head gasket $40
http://photos.freshalloy.com/gallery/d/36140-2/DSCN1186.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1186.JPG.html?g2_navId=x7fa2aabe)
New Thrust bearings $15
VLSD with 5 bolt: includes shafts $315
http://photos.freshalloy.com/gallery/d/34847-2/DSCN1147.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1147.JPG.html?g2_navId=x7fa2aabe)
DOHC Powersteeing lines for s13 good condition $150
FMIC if it doesn't go with the engine $100 (4 couplers but no clamps) also up pipes are turned around in the pic
http://photos.freshalloy.com/gallery/d/34844-2/DSCN1148.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1148.JPG.html?g2_navId=x7fa2aabe)
SR20det stock flywheel $30
http://photos.freshalloy.com/gallery/d/34853-2/DSCN1150.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1150.JPG.html?g2_navId=x7fa2aabe)
Stock SR20det elbow
http://photos.freshalloy.com/gallery/d/34862-2/DSCN1154.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1154.JPG.html?g2_navId=x7fa2aabe)
S14 radiator $100 (includes i believe it is the ac fan)
http://photos.freshalloy.com/gallery/d/34898-2/DSCN1166.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1166.JPG.html?g2_navId=x7fa2aabe)
s13 radiator stock
http://photos.freshalloy.com/gallery/d/34865-2/DSCN1160.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1160.JPG.html?g2_navId=x2989bc0f)
stock SR20det valvetrain.. Its all been cryogenicly treated and is in working condition. I believe I have two sets of (springs, valves) 1 set of retainers.
all together srpings, valves and retainers $50
Alternator for SR20det redtop $50
-----------------------------------------------------------------------------
Some KA SOHC parts
AC condencer and core $100
http://photos.freshalloy.com/gallery/d/34835-2/DSCN1078.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1078.JPG.html?g2_navId=x2989bc0f)
http://photos.freshalloy.com/gallery/d/34838-2/DSCN1075.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1075.JPG.html?g2_navId=x2989bc0f)
throttle body $40
http://photos.freshalloy.com/gallery/d/34868-2/DSCN1156.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1156.JPG.html?g2_navId=x2989bc0f)
Fan shroud for KA $30
http://photos.freshalloy.com/gallery/d/34874-2/DSCN1155.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1155.JPG.html?g2_navId=x2989bc0f)
ECU stock $40
stock MAF sensor $30
http://photos.freshalloy.com/gallery/d/34889-2/DSCN1163.JPG (http://photos.freshalloy.com/gallery/v/lutz5329/DSCN1163.JPG.html?g2_navId=x2989bc0f)
s13 automatic trans brace $10
alternator (not %100 it works) $30
ALL prices are OBO so if you need any of this stuff feel free to make some offers.
Like always I probably forgot some parts so ask and I'll let you know if I have what you need.
Thanks for looking. have a good one
PM offers or if you have any question