jaytv1019
10-20-2008, 08:33 PM
Hey guys, I was going to sell the car but decided to keep it and part out the motor and all the SR parts that I have.
SR20DET Redtop swap(~4,000 miles since rebuild)
- Greddy RAS
- Brian Crower 264* cams
- Brian Crower valve springs
- New valve guides
- Mahle 86.5mm 8.5:1 CR pistons
- OEM rods (new bearings)
- ARP rod bolts
- Used ARP head studs (recomend getting new ones)
- Polished and balanced crank (new bearings)
- New timing kit
- New water & oil pump (front cover)
- eBay pulley kit (oem crank pulley installed)
- Greddy oil pan (real)
- Complete Redtop harness (was in my S14)
- Redtop ECU tuned by Enthalpy for this setup (750cc injetors not included)
- Intake pipe with AEM filter and Z32 MAF (cold air, went into wheel well)
- Fresh transmission
- B&M short shifter
- Exedy Stage 3 clutch
- Filled motor and trans mounts
- AN fittings and lines, heater hoses, all sensors are in working order
- The head has been removed and a new head gasket will be needed, not included
- Intake manifold, exhaust manifold, turbo, intercooler, downpipe, fuel system not included
- Idle air controll valve, newer and is included
- Throtle body and cable included
$3450 OBO - NO LOW BALLERS
Full Race Twin Scroll Turbo Kit
- GT3071r .63 a/r, v-band exhaust housing, twin scroll (perfect condition)
- Full Race TS manifold, 2nd gen, 44mm wastegate v-band
- TiAL 44mm wastegate, silver, AN fittings and ss vacuum line
- Full Race 3" v-band downpipe, wrapped with black heat wrap, 2 O2 bungs
- AN fitings and lines for turbo (Water in and out, oil in, flange for oil out)
$2,800
Greddy Intake manifold
- powder coated black
- IAT sensor bung
- IACV is not included
- Thermal gasket/spacer included
$300
Greddy VLSP FMIC + TiAL 50mm BOV
- piping powder coated graphite
- black Vibranit Performance couplers
- Vibrant Performance T-bolt clamps
- TiAL 50mm bov, black, on cold pipe
$600 -OR- $425 with out BOV or Cold pipe
eBay Down Pipe
$50
Apexi N1 Cat back exhaust
$250
ACT Stage II clutch (Used 50 miles)
$250
SNG Fuel Rail, powder coated Graphit
- AN Fittings and SS lines
- All hardware
$75
RC Engineering 750cc injectors
- Top Feed
$275
($325 for both rail and injectors)
SR20 Used Starter
$100
Thanks for looking!
SR20DET Redtop swap(~4,000 miles since rebuild)
- Greddy RAS
- Brian Crower 264* cams
- Brian Crower valve springs
- New valve guides
- Mahle 86.5mm 8.5:1 CR pistons
- OEM rods (new bearings)
- ARP rod bolts
- Used ARP head studs (recomend getting new ones)
- Polished and balanced crank (new bearings)
- New timing kit
- New water & oil pump (front cover)
- eBay pulley kit (oem crank pulley installed)
- Greddy oil pan (real)
- Complete Redtop harness (was in my S14)
- Redtop ECU tuned by Enthalpy for this setup (750cc injetors not included)
- Intake pipe with AEM filter and Z32 MAF (cold air, went into wheel well)
- Fresh transmission
- B&M short shifter
- Exedy Stage 3 clutch
- Filled motor and trans mounts
- AN fittings and lines, heater hoses, all sensors are in working order
- The head has been removed and a new head gasket will be needed, not included
- Intake manifold, exhaust manifold, turbo, intercooler, downpipe, fuel system not included
- Idle air controll valve, newer and is included
- Throtle body and cable included
$3450 OBO - NO LOW BALLERS
Full Race Twin Scroll Turbo Kit
- GT3071r .63 a/r, v-band exhaust housing, twin scroll (perfect condition)
- Full Race TS manifold, 2nd gen, 44mm wastegate v-band
- TiAL 44mm wastegate, silver, AN fittings and ss vacuum line
- Full Race 3" v-band downpipe, wrapped with black heat wrap, 2 O2 bungs
- AN fitings and lines for turbo (Water in and out, oil in, flange for oil out)
$2,800
Greddy Intake manifold
- powder coated black
- IAT sensor bung
- IACV is not included
- Thermal gasket/spacer included
$300
Greddy VLSP FMIC + TiAL 50mm BOV
- piping powder coated graphite
- black Vibranit Performance couplers
- Vibrant Performance T-bolt clamps
- TiAL 50mm bov, black, on cold pipe
$600 -OR- $425 with out BOV or Cold pipe
eBay Down Pipe
$50
Apexi N1 Cat back exhaust
$250
ACT Stage II clutch (Used 50 miles)
$250
SNG Fuel Rail, powder coated Graphit
- AN Fittings and SS lines
- All hardware
$75
RC Engineering 750cc injectors
- Top Feed
$275
($325 for both rail and injectors)
SR20 Used Starter
$100
Thanks for looking!