PDA

View Full Version : TX Built KA-T + goodies

slideways2004
08-13-2008, 07:52 PM
Engine - 91 DOHC KA -complete w/everything listed below
- Block: vat dipped, decked, bored .020" over, shot peened
- Head: vat dipped, decked, pressure tested
- CP forged pistons CR 9.0:1, .020" oversized
-shot peened stock rods
- cut/balanced crank
- Clevite Bearings (oversized)
- Nissan Gasket set
- ARP head studs
- Oil pan modified for 5/8" oil return
- Stripped Intake manifold of all emissions devices. secondary butterflies ect.
-----$1300 assembled head and block-----
- Stripped Intake manifold of all emissions devices. secondary butterflies ect.


- RevHard Cast top mount manifold -$250
- 50T T3/T04e -$300
- 38MM Turbonetics evo wastegate -
- ATPturbo 38mm wastegate flange w/ 1.5" dump tube-$150

- ClutchMasters Stage 5: 6puck unsprung clutch kit *still in box* - $250
- Resurfaced OE Flywheel- $50

- Painless Wiring 12 Circuit harness w/ 8 switch Panel - $250

http://i28.photobucket.com/albums/c231/strustx/projects13/ka3.jpg
http://i28.photobucket.com/albums/c231/strustx/projects13/ka2.jpg
http://i28.photobucket.com/albums/c231/strustx/projects13/ka.jpg
http://i28.photobucket.com/albums/c231/strustx/projects13/DSC01791.jpg
http://i33.tinypic.com/1432qva.jpg\
http://i35.tinypic.com/wrg760.jpg
http://i35.tinypic.com/wrg760.jpg
http://i35.tinypic.com/fz57nr.jpg
OperationSr20
08-13-2008, 08:10 PM
I am attemptiing to sell my turbo, and now my manifold, and if I do I will be in touch to use the money from my sales to buy your mani and or turbo.

Nice price on that Block too, if only I had the money!

Also, what kind of Turbo Elbow did you use for your setup?
s13_Angelo
08-13-2008, 08:35 PM
if that manifold for a t3 i just bought a t3 from mercedez and i was wondering if ur manifold would work with it
enjoisk8board891
08-13-2008, 09:30 PM
how many miles since the build?
Drift_Magik
08-13-2008, 09:42 PM
willing to ship engine?
slideways2004
08-14-2008, 10:36 AM
if that manifold for a t3 i just bought a t3 from mercedez and i was wondering if ur manifold would work with it

it is a t3 flange. if your turbo has a regular t3 flange, it will work. i'm not sure how the turbo sits, b/c it MIGHT create some clearance problems. im not sure about that

0 miles on the engine. red assembly lube can still be seen
Drift_Magik
08-14-2008, 01:29 PM
maybe u didnt see my post....are u willing to ship at buyers expense?
slideways2004
08-16-2008, 05:27 PM
i can but its going to cost a lot of money. unless i am taking the the wrong place to ship it. have any ideas on shipping??
OperationSr20
08-16-2008, 05:43 PM
I'm still doing all I can to grab that manifols from you. Is that price firm? Also, I'm not sure if you saw or not, but what kind of Turbo Elbow did you use with your setup?
slideways2004
08-17-2008, 04:33 PM
I'm still doing all I can to grab that manifols from you. Is that price firm? Also, I'm not sure if you saw or not, but what kind of Turbo Elbow did you use with your setup?

there is no turbo elbow. its downpipe straight off the turbo
punk138
08-17-2008, 04:47 PM
willing to part the pistons? i have a friend who's in the market for some.