HKS Dragger Exhaust Question

[Erjay1]

My s14 came with an HKS Super Dragger Exhaust. After reading about it on a few websites I think the pipe diameter is 65mm. Isnt that 2.5"?? I need a full 3" exhaust. Can someone confirm this?

[SoSideways]

You can take it off real quick and measure the piping yourself....

[ROUGE180]

65mm = 2.559055118113 inches.

msglngth

[g-via]

you. are. fucking. useless.

tape measure it? google the conversion?! holy shit, I'm speechless. You had the numbers infront of you, but didnt know how to fucking convert it?>!!?!?!!?!

[Erjay1]

65mm = 2.559055118113 inches.

msglngth

Thanks alot dude.

All you other non-help fool idiots can go choke on a big fat one.

[SoSideways]

Thanks alot dude.

All you other non-help fool idiots can go choke on a big fat one.

I had a friend who had an HKS Dragger exhaust on his S13 hatch that had around 3" piping.

It was never on HKS USA's site.

What does that have to do with you?

Your exhaust could have been an imported one, not made for the KA but for the SR, which would mean it would be 3" or there abouts.

The only way to find out for sure, is for your lazy ass to get down there under the fucking car, use your fucking eyes, some sort of measuring device, and fucking measure the fucking diameter.

Coming on here, asking a pretty dumb question, when all you had to do was jack your fucking car up and do some fucking work yourself.

Jesus.

Do we need to call your mom for you to wipe your ass too?

PS - you gave me a + rep with your "lick my balls" comment. Thanks. Here's a neg rep for you for being a lazy idiot that does not know how to use conversion calculators, google, and also do not know how to do research on the interwebz.

[memo92]

Is your motor an SR or a KA? If it's an SR a 3" system is resonable to use. If your running a KA you are good with a 2.5" exhaust system.
I always liked the look of the Super Dragger, it's a keeper.

It looks like you did your research on-line, but there comes a time when you have to jack-up your car and do some hands-on research.

[Erjay1]

PS - you gave me a + rep with your "lick my balls" comment. Thanks. Here's a neg rep for you for being a lazy idiot that does not know how to use conversion calculators, google, and also do not know how to do research on the interwebz.

I realized the positive rep after it was all done.
Thanks for the advise. Anyways, Im at work and need to make a decision on my exhaust ASAP. Dont have anytime to run out and start measuring shit. I needed a quick answer and I know that 65mm does not equal 3".....I needed to know exactly what you stated, that it may possibly still be 3" due to being imported. The piping diameter "looks" bigger than a 2.5". With that being said, thanks but fuck off with the rest of your comments. You and anyone else that is always quick to give a smart ass answer.
I come from a 350z forum where ppl were always helpful and very knowledgeable. Just have to get used to dumbshits like you.

[EDacIouSX]

you. are. fucking. useless.

tape measure it? google the conversion?! holy shit, I'm speechless. You had the numbers infront of you, but didnt know how to fucking convert it?>!!?!?!!?!


for real. not only that did you not graduate hs? i mean come on..

cm --> inches is 2.54cm = 1 inch

2.54 cm = 25.4mm. wtf fail

[SoSideways]

...I needed to know exactly what you stated, that it may possibly still be 3" due to being imported. The piping diameter "looks" bigger than a 2.5".

Then how do you propose you find out the exact diameter of the piping?

If I were you, I'd measure it, to be sure.


With that being said, thanks but fuck off with the rest of your comments. You and anyone else that is always quick to give a smart ass answer.
I come from a 350z forum where ppl were always helpful and very knowledgeable. Just have to get used to dumbshits like you.

There is a shit ton of knowledge on this forum.

We just don't like to hold hands and spoon while spoon feeding information via silver platters.

We like people to do some leg work themselves and learn stuff on their own.

There are also a shit ton more parts out there for the S-chassis than there are for the Z33.

There's probably 2 versions of the HKS Dragger exhaust for each version of the S-chassis, an NA version and a turbo 3" version.

Just from that alone, it's pretty apparent that without some sort of measuring, you wouldn't know for sure.

I TOLD YOU TO MEASURE IT WITH MY FIRST REPLY.

Seriously, we can sit here and give you the run around and tell you it's really 1.25" with 2" thick piping running down the car, making it heavy, but look like you've got a 3" exhaust, but we aren't telling you that. We're telling you to go measure it, or bust out a calculator and figure out that for every inch, there is 25.4mm, that stands for millimeter.

God... why can't people just fucking do anything for themselves anymore these days? And what's with the whiny bitches that get all butt hurt when someone tells them to do work?

[Erjay1]

Whatever dude. Like I said before, I was at work and could no go out and get under my car in business attire. I needed to make a quick decision about my exhaust being that its getting tuned very soon. Wouldnt want it tuned on an exhaust that is anything less than 3". Thanks for the added info on that last post. Now that Im home, I will get under there and measure.

[g-via]

Whatever dude. Like I said before, I was at work and could no go out and get under my car in business attire.

yah shit, wouldn't wanna be caught outside in a mcdonald's uniform, eh?