PDA

View Full Version : Smoke in sr motor


sr20 driver
12-26-2007, 05:47 PM
hey ppl marry christmas. anyways can anyone plz help me heres what happend i had a little more oil in the motor than needed. i stepped on the pedal and all the sudden all this smoke just goes everywere i stop pop the hood and my hole motor is soked in oil and know everytime when i start it white smoke comes out of the valve cover breather tube and the oil cap if i open it another words smoke gets into the motor some how and everytime i get on it my motor is soked in oil. please help make it my christmas presant. thx

motorsnail
12-26-2007, 05:53 PM
You put the oil cap back on? Maybe blown headgasket, I dunno your description makes it sound like a fairy is spraying oil on your motor or somthing. Explain it better

burnsauto
12-26-2007, 05:53 PM
blown engine?

how many quarts did you put in the engine?

have you tried draining the oil, and filling it back up to the correct level?

...you may want to pay attention to basic rules of grammar next time..took me a second to realize what you were trying to explain.

tig_tech
12-26-2007, 06:01 PM
Yea too much oil will hurt the motor than too little. Your probably leaking oil past seals too. Drain that sucker and add the correct amount. Oil is cheaper than a new motor.

sr20 driver
12-26-2007, 06:07 PM
the motor is in oil. i believe the oil is coming from the breather tube because if the leak was somewere lower it wouldnt be on the valve cover and it only spills when u give it load. i put 4 quarts maybe a little more. write know the oil level is good. every thing was good for about two weeks.

WISH ONE
12-26-2007, 06:11 PM
yeah bad things can happen, when you fill it with too much oil. damage piston rings, valve seals, o2 sensors. try and drain and refill like everyone above suggested, you might just get lucky. GL

tig_tech
12-26-2007, 06:12 PM
Ok when its on load your getting crankcase pressure (blow-by) and its exiting through the hose and into your intake or catchtank. Chech that steel fitting on the valve cover and see if its tight or not. Then check the rubber hose and make sure your clamp is tight. Thats the only possible source from everything you tried explaining.

slothonaleash
12-26-2007, 06:14 PM
bad piston rings and/or valve seals add to blow-by gasses and oil flying through the valve cover breather tube

sr20 driver
12-26-2007, 06:20 PM
yes all the clamps are tight except that fitting its not it comes in and out. what about the white smoke were is it cominfg from

tig_tech
12-26-2007, 06:40 PM
If its white smoke then thats coolant. If you cant tell if its white or blueish then my next guess is your valve seals could be shot.

tig_tech
12-26-2007, 06:42 PM
I also think its time for you to run a leak down and compression test to find out the current condition of your engine.

burnsauto
12-26-2007, 10:56 PM
yes all the clamps are tight except that fitting its not it comes in and out. what about the white smoke were is it cominfg from

so you mean the "t fitting" on the side of the valve cover? that shouldnt move at all.

and i dont see how the entire engine could be covered in oil by that one spot.

you may want to pop off the valve cover, take a peak to make sure nothings broken/bent/etc (like an oil squirter......ive never seen one screw up before...but you might as well check.)

SHIFT_*grind*
12-27-2007, 06:46 AM
i put 4 quarts maybe a little more.

Definitely too much oil. From the SR FAQ (http://www.zilvia.net/f/showpost.php?p=711739&postcount=42) in this forum:

Engine Oil: (with filter change): 3 1/4 qt (3.7 L)
(w/o filter change): 3 1/8 qt (3.5 L)

Don't put in more than that, bad stuff can happen (obviously).

sr20 driver
12-27-2007, 08:53 PM
i can tell u one thing for sure my third cylinder has no compression at all. what is it the rings?

drifterRS
12-27-2007, 09:12 PM
i can tell u one thing for sure my third cylinder has no compression at all. what is it the rings?

it could be your valve seals or a bent valve or even your rings are screwed

sr20 driver
12-28-2007, 03:00 PM
does anyone know what exactly might be wrong

sillyvia13
12-28-2007, 03:46 PM
take it to a local shop,your in cali there a million that can help.
you may have a rocker arm off, does it misfire?

sr20 driver
12-29-2007, 02:05 AM
o man tell me what it doesnt do? it does all kinds of crap idles like a fuckin tracktor. probably does misfire but i got spark everywere