rb26tt trbo on a sr

[s13lover93]

are they interchangeable? and if not what are spec on lines and such to work?

[JDMS1lv1a]

Im pretty positive that the RB26 uses the same turbos as the s14/s15 SR

not 100% sure though

[daryl337]

I believe the RB26's use dual CT26's which (and im blowing out my own ass on this one) probably dont have the same flange.

[ALEXTHESUS*PECT]

i thought it ran dual t28 from s14/5 as stated above..........?

[sliEighty]

searching might help


Originally Posted by Burmonster
Okay, I have posted this info before but it is always helpfull. Mods, if you read this, sticky might be good so that people have a stock turbo guide for nissan engines.

And yes the 300z has dual t-25

GARRETT T25
They are from the small series of turbochargers specifically engineered for original-equipment small-capacity engines, have their roots in the ET Pulsar, and culminate in a 'twin' application on the 300ZX twin-turbo VG30DETT. In single form, they are not recommended for performance applications.

Car of Origin: Nissan S13 Silvia/180SX
Engine: CA18DET
Flange: Four-bolt; it fits most Nissan four-cylinder turbo engines
Max. Power Rating: Approximately 130kW
Max. Boost: 1.0bar (14.5psi)
Cover Size: Exhaust 0.48 AR, compressor 0.49 AR
Comments: A small and reasonably ineffiecient turbocharger that should only really be used as a straight fit for an existing CA18DET engine to replace a failed unit. It's not recommended as a bolt-on for a normally aspirated engine of more than 1600cc.
Cost: Normally quite expensive, $450+ due to the replacement demand in the normal service industry for these turbocharger
Rating: One out of five.

Car of Origin: Nissan PS13 Silvia/180SX
Engine: SR20DET
Flange: Same as above
Max. Power Rating: Approximately 160kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: Exhaust 0.64 AR, compressor 0.60 AR
Comments: Improved flowing version of the CA18DET turbo makes it a great straight-fit bolt-on to the CA series, but becomes borderline on even a lightly modified SR20 engine. That the S14 series of cars moved to using a bigger T28-style unit is testimony to this.
Cost: Again, being a straight fit for all of the 2-litre turbo imports makes them an in-demand unit and pushes their cost through the roof. $550+ makes them expensive, but they are a great fit-up for a lightly tuned S13 CA18DET
Rating: Two out of five.


GARRETT T28
The next size up from the T25, the T28 series of turbochargers are more serious items. They are used in twin form on the Nissan Skyline GT-R and singularly on the Pulsar GTi-R, S14 and S15 series Silva/200SX. They make a decent upgrade for the S13 series of cars when more than 150kW are reliably expected to be produced.


Car of Origin: Nissan S14 200SX pre-1996
Engine: SR20DET
Flange: Four-bolt, same as the T25 series.
Max. Power Rating: Approximately 170kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: Exhaust 0.64 AR, compressor 0.60 AR
Comments: The ultimate OE bolt-up to the S13 series of cars, the best part is that it bolts straight on. A good little all-round mid-range turbocharger that has proven itself to be extremely reliable in service.
Cost: Expensive due to their fitment to an Australian-delivered car. Their price starts at $650 for a second-hand unit.
Rating: Three out of five

JDM Vehicles only, not relevean to the UK S14a
Car of Origin: Nissan S14 200SX post-1996, S15
Engine: SR20DET
Flange: Four-bolt, the same as the T25 series
Max. Power Rating: Approximately 170kW or slightly more
Max. Boost: 1.2bar (17.4psi)
Cover Size: Exhaust 0.64 AR, compressor 0.60 AR
Comments: While the housing are the same as the earlier S14 turbocharger, the latter item has sophisticated Garrett ball-bearing internals, which guarantee a faster ramp-up to boost than the previous model. This is the pick of the T28 series.
Cost: They're hard to find second hand due to the relative scarcity of the S14 black rocker cover engines. Normally, you are best off to buy these new from a turbo supplier.
Rating: Four out of five

Car of Origin: Nissan Skyline R32, R33 GT-R
Engine: RB26DETT
Flange: Four-bolt, the same as the T25 series
Max. Power Rating: Approximately 150kW
Max. Boost: 1.3bar (18.8psi)
Cover Size: Exhaust 0.48 AR, compressor 0.60 AR
Comments: They are really only good for use on stock GT-R engines due to their relatively small exhaust housing. For some reason, they seem to be able to handle more boost before turbine failure, but there are still plenty that have let go.
Cost: Anything with a GT-R part number is expensive!
Rating: Two out of five


GARRETT RB20/25 SERIES
Even though many tuners refer to the RB20 and VG30 (single) turbochargers as being a T3, this is not the case. Being a Nissan-branded item and having only Nissan identification markings on them (no AR markings etc.) can make identification difficult. All of the ball-bearing turbos have a telltale 'fatter' centre core section, as well as a bolt through the centre housing, which looks as though it has an effect on the thrust bearing pre-load. Overall, these turbos are very good performers.


Car of Origin: Nissan Skyline R31 GTS
Engine: RB20DET NICS (ribbed rocker cover)
Flange: Four bolt T3 style
Max. Power Rating: 140kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: AR not identified
Comments: A poor-performing turbocharger that was only used on a handful of engines by Nisan before being replaced with the newer technology ball-bearing units. Top-end power is far from good, and the actual response (boost-response time) is also quite poor. It's one to steer away from.
Cost: Dirt-cheap, as they are not in any demand. They have been seen to be as low as $100.
Rating: One out of five

Car of Origin: Nissan Skyline R32 GTS-t
Engine: RB20DET ECCS (silver rocker cover)
Flange: Four bolt T3 style
Max. Power Rating: 160kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: AR not identified
Comments: A big step in the right direction from both Nissan and Garrett. A truely nice turbocharger, complete with modern aerodynamics and ball bearing construction. It's a perfect choice to get the best from an internally stock, standard injector/management set-up. On a CA18 with a custom manifold, they are really good things.
Cost: Reasonable, with some examples floating around the importers for as little as $400. You have to be quick thoughm as they tend to sell fairly quickly.
Rating: Four out of five.

Car of Origin: Nissan Skyline R33 GT25-T
Engine: RB25DET
Flange: Four bolt T3 style
Max. Power Rating: Approximately 185kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: AR not identified
Comments: The big daddy of the range makes the RB25 turbocharger good for almost any mild six-cylinder application. Sparkling boost response in the low-rpm range and a reasonably hard-hitting top end make this the most common upgrade found on the RB20DET. It's highly recommended.
Cost: Being very difficult to get hold of makes them highly variable in price. Sometimes about $700, sometimes more.
Rating: Five out of five.

Car of Origin: Nissan Gloria, 300ZX
Engine: VG30DET
Flange: Four-bolt T3 style
Max. Power Rating: 190kW
Max. Boost: 1.2bar (17.4psi)
Cover Size: AR not identified
Comments: Apparently, these are slightly larger in exhaust housing size than the RB25, but have a fractionally smaller and different trim compressor. Information on these is sketchy, but due to their almost unknown application they are easier to find than the RB25 roller. A good choice, particularly if you put the RB25 compressor and cover straight on. In excess of 200kW have been produced with this combination.
Cost: Fractionally cheaper than the RB25 turbo and not as hard to get. They have been advertised at $650.
Rating: Four out of five

[s13lover93]

hah all bs, like i give :), that is what i was thinking also t28 form the s14/15

[JDMS1lv1a]

hah all bs, like i give :), that is what i was thinking also t28 form the s14/15

so since RB26 turbos are the same as s14/s15 SR's and use four bolt flanges,then yes they're interchangable.

and also an upgrade to s13 SR's. so there's your answer:)

[steve shadows]

I didnt read any of the crap above

RB25/26 is a T3 flange

its not bolt on

RR26 is dual t2 flanged turbos

[bardabe]

yes I have personally worked on sevceral RB26's and I can tell you they are Dual T28's and yes they are ball bearing. =)

[Sileighty_85]

I didnt read any of the crap above

RB25/26 is a T3 flange

its not bolt on

RR26 is dual t2 flanged turbos

The RB26DETT Uses Dual T28 BB Turbos same Turbo's & Exhaust flange as the the S14-15 T28's

RB20 & 25's use the Same T3/T4 Flange

[s13lover93]

iight cool thanks for then help

[ALEXTHESUS*PECT]

good info. i learn something new everyday. yesterday was that bengay and testicals don't mix.

[s13lover93]

hah damn i lernt that a few years ago lol

[Sileighty_85]

good info. i learn something new everyday. yesterday was that bengay and testicals don't mix.

ROTFL :rofl: Im stealing that for my sig lol

[bigOdom1]

while that list is somewhat accurate it does have its faults. some pre 1996 s14 are bbT28.

[lazierhobo]

at one point i thought i had read something about the RB26DETT using T28s with ceramic turbine blades? something about them liking to come apart at much at all above stock boost? just a question.

[Sileighty_85]

while that list is somewhat accurate it does have its faults. some pre 1996 s14 are bbT28.

All JDM S14's T-28's have have BB Turbos the only T28 That doesnt is the Pulsar GTI-R it uses Brass Journal Bearings

[bigOdom1]

All JDM S14's T-28's have have BB Turbos the only T28 That doesnt is the Pulsar GTI-R it uses Brass Journal Bearings

i am unsure of this as the only s14 t28's i have seen other than my own have all been bbT28's. so he may be correct speak up if you have a journal T28 on your s14 other wise i am beginning to think that is the case too. even though its posted otherwise in many other threads.

[ch1873857]

any m24 1-2 t28 is BB. the gtr uses smaller t28s than those used on s14s and s15s. although you can use it, its not going to yield the same gains.

[s13lover93]

i love this place its so easy to go from interchangeable rb turbo to what kind it is hah good shit

[surge s14]

All JDM S14's T-28's have have BB Turbos the only T28 That doesnt is the Pulsar GTI-R it uses Brass Journal Bearings


wait if that ture then whats the difference between s14/s15 t-28's? or spec R?:eek3:

[ch1873857]

nothing..the s15s had a different cast turbine housing that separated the the wg and the turbine exhaust flow. thats all i can think of

[iwishiwas-all*]

would anyone be able to tell if this part number is from a t28 off of a rb26???
thanks


v8 1660J 14414 05U21 46607 1-8

[Sileighty_85]

wait if that ture then whats the difference between s14/s15 t-28's? or spec R?:eek3:

the diff between the S-14 and S15 T-28 is the exhaust housing is bigger on the S-15 T-28

[daryl337]

what about the r34? :| the 32 and 33 use the t28. Im curious about the 34 now. XD

[JVD]

I didnt read any of the crap above

RB25/26 is a T3 flange

its not bolt on

RR26 is dual t2 flanged turbos

I'm assuming he meant RB20/25 = T3 and RB26 = dual T2...

[daryl337]

doh.. I realized why I thought it was a ct26. Supra TT's use them. XD Im an idiort. With the R. Idiort.

[ch1873857]

the diff between the S-14 and S15 T-28 is the exhaust housing is bigger on the S-15 T-28

what size exhaust housing is on the s15?

[racer98]

are they interchangeable? and if not what are spec on lines and such to work?

R32 turbos for examples

http://i43.photobucket.com/albums/e359/racer98/DSCN1467.jpg

http://i43.photobucket.com/albums/e359/racer98/DSCN1459.jpg

http://i43.photobucket.com/albums/e359/racer98/DSCN1458.jpg

http://i43.photobucket.com/albums/e359/racer98/DSCN1457.jpg

[ch1873857]

i think that says a/r .42. s14/s15 is .60 thanks for the pics man.

[nissdrvr14]

im currently tossing on an rb26 turbo on my ka. its t28 (normal t2 exhaust input flange) with a smaller exhaust turbine (.42 i believe). the exhaust output flange is a different bolt pattern though, making this turbo not interchangable with an sr t25/28 unless you have the rb elbow.

http://i99.photobucket.com/albums/l297/nissdrvr/IMG_5651.jpg

[95240s14]

who gives a shit if it would fit or not....its like buying an rb25 turbo for your rb20, WASTE OF TIME!! Do some research and buy a REAL turbo. I'm not saying the stock stuff is junk, cuz its not, but if your gonna spend some $$, spend it right.

[ch1873857]

yeah. definately. a gtr turbo has what a .48 exhaust and .42 compressor housings? my s14 bb is .64 and .60 thats a considerable difference.

[nissdrvr14]

who gives a shit if it would fit or not....its like buying an rb25 turbo for your rb20, WASTE OF TIME!! Do some research and buy a REAL turbo. I'm not saying the stock stuff is junk, cuz its not, but if your gonna spend some $$, spend it right.

i got mine hand-me-down style, so im runnin with it.... why else would i t2 a ka? (besides insane torque and throttle response....)