JDS Performance
04-25-2007, 07:11 PM
FS; 95 S14 240sx MT SE in NC
- Starting at $7500 OBO
- Located in Concord, NC 28027
about 10 mins from UNCC/Lowes Motor Speedway/Concord Mills Mall
If there is anything you dont like about my car/price/or anything at all - keep it to yourself!
Car
- 97,XXX miles
- Auto to 5 speed swap - Everything works! No codes!
- Leather - super clean car!
- Clean title in hand - I am the 3rd owner - and I did all work to it
- Stock shifter - weighted shift knob
- New door handles
- MT shifter trim & rubber boot
- MT clutch and brake pedals
- MT brake booster and master cylinder - full system bled w/ new fluid
- 95 ODBII MT ECU
- s14 non ABS MT driveshaft
- New Nismo steering rack bushings
- Used Nismo Motor Mounts
- Used Nismo Tension Rod Bushings inside stock Tension Rods
- New Energy Suspension Tie Rod End bushings
- F&R Brake rotors - 1.5k miles
- F&R Brake pads - 1.5K miles
- Silvia Grill / Black
- Zenki Eyelids
- New flushed and bled coolant / Prestone 50/50
- Mobil 1 10w30
- Red Line 75W90 gear oil
- Lucas P/S fluid
-No leaks or issues whatso ever!
-5 speed swapped was performed by me, and was video documented - as I made a 5 speed swap DVD
- Car was in a small bump up in front from previous owner - as you can see the paint chipped off the front bumper - eveything was fixed by a pro shop - and no frame damage - it just bump the bumper back and cracked the headlight - which was replaced with a new one.
Motor
- New Exedy Clutch kit - street/strip - new MT Pilot Bushing - New Heat Treated Pressure Plate bolts(Loctited)
- Gold / TRG powder coated valve cover
- Intake and front covers in high heat silver - all new gaskets
- New belts
- New Z32 fuel filter and hoses
- OBX Radiator hoses / Blue
- New Injen short ram / Chrome
- New NGK wires/Plugs
- New Distributor Cap and Rotor Button
- New front O2 Sensor
- New Knock Sensor
- New Water Pump
- New Oil Pan
- Front covers re-sealed
- All gaskets replaced - except the head gasket
- All Emssions/EGR removed - (100k ohm 1/4 watt resistor on EGR temp sensor) - 95' and lower doesnt have to pass emissions
Tranny - All sensors wired up!
-96' MT tranny shifts perfect
-All New
-Heat Treated Bellhousing/Gusset Bolt/Nuts
-Tranny Clutch Fork
-Tranny Release Bearing Holder
-Tranny Release Bearing Spring
-Tranny NISMO Release Fork Pivot
-Tranny Fork Dust Boot
-Tranny Rear Dust Cover
-Tranny Front Cover Gasket
-Tranny Striker Arm
-Tranny Striker Arm Pin
-Tranny Extension Housing Seal
-Tranny Rear Oil Seal
-Tranny Front Oil Seal
- Crank Angle Sensor
- Master/Slave Cylinder
- Steel Braided Line from master to slave
- Fidanza Flywheel - New Heat Treated Bolts(Loctited)
Exhaust
- Stock
Suspension
- KYB AGX shocks / H&R Sport Springs
- TCSportline front strut bar
- Professional Alignment after shocks/springs installed
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0006-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/rearend.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0006-2.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0007.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0004-2.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0001-3.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0005-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0010.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0008.jpg
http://i82.photobucket.com/albums/j274/joshds25/DSCF0015-4.jpg
http://i82.photobucket.com/albums/j274/joshds25/DSCF0040-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0003-1.jpg
- Starting at $7500 OBO
- Located in Concord, NC 28027
about 10 mins from UNCC/Lowes Motor Speedway/Concord Mills Mall
If there is anything you dont like about my car/price/or anything at all - keep it to yourself!
Car
- 97,XXX miles
- Auto to 5 speed swap - Everything works! No codes!
- Leather - super clean car!
- Clean title in hand - I am the 3rd owner - and I did all work to it
- Stock shifter - weighted shift knob
- New door handles
- MT shifter trim & rubber boot
- MT clutch and brake pedals
- MT brake booster and master cylinder - full system bled w/ new fluid
- 95 ODBII MT ECU
- s14 non ABS MT driveshaft
- New Nismo steering rack bushings
- Used Nismo Motor Mounts
- Used Nismo Tension Rod Bushings inside stock Tension Rods
- New Energy Suspension Tie Rod End bushings
- F&R Brake rotors - 1.5k miles
- F&R Brake pads - 1.5K miles
- Silvia Grill / Black
- Zenki Eyelids
- New flushed and bled coolant / Prestone 50/50
- Mobil 1 10w30
- Red Line 75W90 gear oil
- Lucas P/S fluid
-No leaks or issues whatso ever!
-5 speed swapped was performed by me, and was video documented - as I made a 5 speed swap DVD
- Car was in a small bump up in front from previous owner - as you can see the paint chipped off the front bumper - eveything was fixed by a pro shop - and no frame damage - it just bump the bumper back and cracked the headlight - which was replaced with a new one.
Motor
- New Exedy Clutch kit - street/strip - new MT Pilot Bushing - New Heat Treated Pressure Plate bolts(Loctited)
- Gold / TRG powder coated valve cover
- Intake and front covers in high heat silver - all new gaskets
- New belts
- New Z32 fuel filter and hoses
- OBX Radiator hoses / Blue
- New Injen short ram / Chrome
- New NGK wires/Plugs
- New Distributor Cap and Rotor Button
- New front O2 Sensor
- New Knock Sensor
- New Water Pump
- New Oil Pan
- Front covers re-sealed
- All gaskets replaced - except the head gasket
- All Emssions/EGR removed - (100k ohm 1/4 watt resistor on EGR temp sensor) - 95' and lower doesnt have to pass emissions
Tranny - All sensors wired up!
-96' MT tranny shifts perfect
-All New
-Heat Treated Bellhousing/Gusset Bolt/Nuts
-Tranny Clutch Fork
-Tranny Release Bearing Holder
-Tranny Release Bearing Spring
-Tranny NISMO Release Fork Pivot
-Tranny Fork Dust Boot
-Tranny Rear Dust Cover
-Tranny Front Cover Gasket
-Tranny Striker Arm
-Tranny Striker Arm Pin
-Tranny Extension Housing Seal
-Tranny Rear Oil Seal
-Tranny Front Oil Seal
- Crank Angle Sensor
- Master/Slave Cylinder
- Steel Braided Line from master to slave
- Fidanza Flywheel - New Heat Treated Bolts(Loctited)
Exhaust
- Stock
Suspension
- KYB AGX shocks / H&R Sport Springs
- TCSportline front strut bar
- Professional Alignment after shocks/springs installed
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0006-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/rearend.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0006-2.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0007.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0004-2.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0001-3.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0005-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0010.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0008.jpg
http://i82.photobucket.com/albums/j274/joshds25/DSCF0015-4.jpg
http://i82.photobucket.com/albums/j274/joshds25/DSCF0040-1.jpg
http://i82.photobucket.com/albums/j274/joshds25/95%20240sx%20SE%20New/DSCF0003-1.jpg