adictd2b00st
09-25-2006, 08:01 AM
Ok so i've been doing alot of thinking lately, and as much as i love this car it's probably in my best interest moneywise to sell it since i realisticly only drive it about twice a week for the 6 good months of weather we get here in buffalo each year. time to get my priorities in order :(
that being said, i don't HAVE to sell it, so don't expect a low ball offer to be accepted, be reasonable here people :)
ok, on with the good stuff:
1994 Mazda RX7
5 sp
96k on the clock, about 12k on the motor (details on that below)
Montego Blue
Black Interior (leather)
always stored winters, rarely even seen rain
Mods list:
Engine: Stage III street port with Ionetti ceramic apex seal by Hayes
Fully balanced rotating assembly
Silicone water seals
Upper/Lower intake has been polished
Secondary Throttle Butterflies have been removed
Polished Water Pump & Thermostat Housing
Single turbo conversion ( GT40r, custom manifold, 3.25" downpipe, 3" midpipe), hks ssqv bov, hks 50mm wastegate, racing beat dual tip catback, custom vmount (spearco intercooler/ fluidyne radiator, aluminum brackets), Greddy coolant breather tank, Greddy elbow, dual earls oil coolers with -10an line/fittings, dual intank walbro 255 fuel pumps, 850cc primary injectors, 1600cc secondary injectors, rx7store secondary fuel rail, ported stock primary fuel rail, SX fuel pressure regulator, -6an fuel line back to fuel tank, fuel filter relocated, magnecore wires/ ngk plugs, oil catch can, apexi 3 bar map sensor , Coolingmist Varicool Meth/Water Injection kit
Drivetrain: ACT Street/Strip clutch, Turbo II VLSD, A-spec tranny brace, mazdatrix short throw shifter
Suspension/ Brakes: mazdaspeed coilovers, jim lab unobtanium suspension bushings, cusco rear strut bars, brembo rotors/ ebc pads / Goodrich SS brake lines and Speed Bleeders
Rims/Tires: Apexi rims (17x8.5 F 17x9 R / Falken Ziex tires (235/45 F 255/40 R)
Electronics: Apexi Power FC w/ commander, hks twinpower ignition, autometer guages ( oil press, water temp, boost, egt), flyrx7 dash guage pod, greddy profec type-s boost controller , FJO wideband o2
Interior:
28% 3M tint
Nakamichi CD player
Eclipse 6.5" door speakers
JDM armrest
Exterior: KS style c/f hood, mazdaspeed front bumper, 99 turn signals
misc info:
brand new engine harness from mazda ( replaced last winter)
Oil change every 2000 miles Amsoil 10w30
Evans NPG+ coolant
premix - 1 oz of amsoil 2 cycle for every 1 gal of gas
Gear oil - Neo 75-90 HD GL5
Car currently is tuned for 20psi on 93 octane, with a 50/50 mix of water/meth. ARF @ WOT is consistent low 11's to redline, engine pulls VERY smooth no misfires or anything like that. When i had the car tuned by Enzo (www.enzo-racing.com) on long island he kept saying how healthy my motor sounded with each dyno pull
Car doesn't NEED anything....... brakes are good , tires have plenty of tread left, isn't burning any oil (other than the premix of course ;) ) no known problems with the car it starts right up everytime. everything in the interior works, nothing is broken/faded. theres some slight wear on the driver side seat, but very minor.
The only thing that i was going to do next is get the rear end replaced as it does have a whine on decel (ring and pinion i suspect) but it hasn't effected driveability at all.
Exterior wise the paint is in VERY good condition for being original. There is 2 small scratches, one on the driver side near the door, and a second on the rear bumper. The front bumper has a hairline crack in the fiberglass.
Now for some pics:
http://i31.photobucket.com/albums/c354/adictd2b00st2/19001141721.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/19001184096.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/sideclean.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/rearclean.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/enginebay.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/interior.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/dump.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/fuelpumprelocation.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/DSCF3523.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/jay_rx7.jpg
Thanks for looking, if anyone has any questions just shoot me a PM or post in this thread...... if you drove this car you will NOT be dissappointed, i've never tracked the car on this current setup but i can tell you from a roll (20 -120mph) i am DEAD EVEN with my friends evo that runs 11.1 @131 on c16 so if i had to guess this car is very close to 500whp. NO CORNERS WERE CUT BUILDING THIS CAR theres a good $800 in -an fittings / lines in this car alone! All work has been professionally done, and all fab work was custom one off
Asking $23,500 OBO, No Lowballs, and no i will not part it out. Car is located in Buffalo, NY. Would also be possibly interested in trading + cash if the right 240 came along
that being said, i don't HAVE to sell it, so don't expect a low ball offer to be accepted, be reasonable here people :)
ok, on with the good stuff:
1994 Mazda RX7
5 sp
96k on the clock, about 12k on the motor (details on that below)
Montego Blue
Black Interior (leather)
always stored winters, rarely even seen rain
Mods list:
Engine: Stage III street port with Ionetti ceramic apex seal by Hayes
Fully balanced rotating assembly
Silicone water seals
Upper/Lower intake has been polished
Secondary Throttle Butterflies have been removed
Polished Water Pump & Thermostat Housing
Single turbo conversion ( GT40r, custom manifold, 3.25" downpipe, 3" midpipe), hks ssqv bov, hks 50mm wastegate, racing beat dual tip catback, custom vmount (spearco intercooler/ fluidyne radiator, aluminum brackets), Greddy coolant breather tank, Greddy elbow, dual earls oil coolers with -10an line/fittings, dual intank walbro 255 fuel pumps, 850cc primary injectors, 1600cc secondary injectors, rx7store secondary fuel rail, ported stock primary fuel rail, SX fuel pressure regulator, -6an fuel line back to fuel tank, fuel filter relocated, magnecore wires/ ngk plugs, oil catch can, apexi 3 bar map sensor , Coolingmist Varicool Meth/Water Injection kit
Drivetrain: ACT Street/Strip clutch, Turbo II VLSD, A-spec tranny brace, mazdatrix short throw shifter
Suspension/ Brakes: mazdaspeed coilovers, jim lab unobtanium suspension bushings, cusco rear strut bars, brembo rotors/ ebc pads / Goodrich SS brake lines and Speed Bleeders
Rims/Tires: Apexi rims (17x8.5 F 17x9 R / Falken Ziex tires (235/45 F 255/40 R)
Electronics: Apexi Power FC w/ commander, hks twinpower ignition, autometer guages ( oil press, water temp, boost, egt), flyrx7 dash guage pod, greddy profec type-s boost controller , FJO wideband o2
Interior:
28% 3M tint
Nakamichi CD player
Eclipse 6.5" door speakers
JDM armrest
Exterior: KS style c/f hood, mazdaspeed front bumper, 99 turn signals
misc info:
brand new engine harness from mazda ( replaced last winter)
Oil change every 2000 miles Amsoil 10w30
Evans NPG+ coolant
premix - 1 oz of amsoil 2 cycle for every 1 gal of gas
Gear oil - Neo 75-90 HD GL5
Car currently is tuned for 20psi on 93 octane, with a 50/50 mix of water/meth. ARF @ WOT is consistent low 11's to redline, engine pulls VERY smooth no misfires or anything like that. When i had the car tuned by Enzo (www.enzo-racing.com) on long island he kept saying how healthy my motor sounded with each dyno pull
Car doesn't NEED anything....... brakes are good , tires have plenty of tread left, isn't burning any oil (other than the premix of course ;) ) no known problems with the car it starts right up everytime. everything in the interior works, nothing is broken/faded. theres some slight wear on the driver side seat, but very minor.
The only thing that i was going to do next is get the rear end replaced as it does have a whine on decel (ring and pinion i suspect) but it hasn't effected driveability at all.
Exterior wise the paint is in VERY good condition for being original. There is 2 small scratches, one on the driver side near the door, and a second on the rear bumper. The front bumper has a hairline crack in the fiberglass.
Now for some pics:
http://i31.photobucket.com/albums/c354/adictd2b00st2/19001141721.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/19001184096.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/sideclean.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/rearclean.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/enginebay.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/interior.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/dump.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/fuelpumprelocation.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/DSCF3523.jpg
http://i31.photobucket.com/albums/c354/adictd2b00st2/jay_rx7.jpg
Thanks for looking, if anyone has any questions just shoot me a PM or post in this thread...... if you drove this car you will NOT be dissappointed, i've never tracked the car on this current setup but i can tell you from a roll (20 -120mph) i am DEAD EVEN with my friends evo that runs 11.1 @131 on c16 so if i had to guess this car is very close to 500whp. NO CORNERS WERE CUT BUILDING THIS CAR theres a good $800 in -an fittings / lines in this car alone! All work has been professionally done, and all fab work was custom one off
Asking $23,500 OBO, No Lowballs, and no i will not part it out. Car is located in Buffalo, NY. Would also be possibly interested in trading + cash if the right 240 came along