removing ssr faces - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

rancid240 · 11-20-2003, 05:56 PM

Any easy way to do this? Can i attack it with a hex wrench and a wrench from the other side? i am just making sure that neither side is welded on (aka the hex part is welded to the face, or the bolt part is a permenant part of the disk)

boro240 · 11-20-2003, 06:39 PM

are you sure theyre 3-piece wheels? you can only remove the faces of 3-piece wheels.

nokeone · 11-20-2003, 07:04 PM

reverse face of 3 piece wheel = woot woot..

..madddddd low offset..

stretch240sx · 11-20-2003, 07:33 PM

Quote:

Originally posted by nokeone
reverse face of 3 piece wheel = woot woot....madddddd low offset..

mad low offset= mad wheelbearing wear..

fooddude · 11-21-2003, 02:53 PM

Quote:

Originally posted by stretch240sx
mad low offset= mad wheelbearing wear...

finally...someone speaks the truth! I guess it's wirth it though to have mad lip yo! lol

Dousan_PG · 11-21-2003, 03:02 PM

Quote:

Originally posted by stretch240sx
mad low offset= mad wheelbearing wear...

damn 2 years mad track use w/ low offset wheels and bearings are still 100% tip top. same goes for LOTS of friends

wear is MINIMAL next to nothing.

http://forums.freshalloy.com/ubbthre...b=5&o=&fpart=1

that's a fun thread.

rancid240 · 11-21-2003, 04:23 PM

my question still remains unanswered

The ssr rims have tires with air in them, Is this why the bolts wont budge? If so can I just take say my tire pressure gauge, let all the air out, and then swap the faces?

old_s13 · 11-21-2003, 05:12 PM

Quote:

Originally posted by dousan36
damn 2 years mad track use w/ low offset wheels and bearings are still 100% tip top. same goes for LOTS of friends

wear is MINIMAL next to nothing.

http://forums.freshalloy.com/ubbthre...b=5&o=&fpart=1

that's a fun thread.

Im running 17mm front and 12mm rear solid alum spacers that were machined by fred (wheelspacers.com), I use the longest nismo wheel studs and have had NO issues for the past few years now.. of course, hard driving and LA roads (downtown is no stranger). I think using a quality rim is more important than using or not using spacers. If you DO decide to use spacers, use good quality ones. If you dont feel like splurging on wheel studs, wheel adaptors may also be a better choice for some.. depends on how thick of a spacer you need to go.

rancid240> my question still remains unanswered

Take your wheels to a wheel shop that specializes on working with multi-piece wheels.

- Mike

11-20-2003, 05:56 PM	#1
rancid240 Post Whore! Join Date: Jan 2002 Location: Irvine CA Posts: 2,770 Trader Rating: (72) Feedback Score: 72 reviews	removing ssr faces Any easy way to do this? Can i attack it with a hex wrench and a wrench from the other side? i am just making sure that neither side is welded on (aka the hex part is welded to the face, or the bolt part is a permenant part of the disk)

11-20-2003, 07:04 PM	#3
nokeone on strike three. Join Date: Mar 2003 Location: Santa Cruz, California Age: 42 Posts: 3,282 Trader Rating: (0) Feedback Score: 0 reviews	reverse face of 3 piece wheel = woot woot....madddddd low offset.. __________________ panda; rockin your socks from the Bay to LA to SD, yay! Pink GodziRa

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-20-2003, 06:39 PM	#2
boro240 Zilvia FREAK! Join Date: Jan 2003 Location: Tucson, AZ Age: 36 Posts: 1,324 Trader Rating: (0) Feedback Score: 0 reviews	are you sure theyre 3-piece wheels? you can only remove the faces of 3-piece wheels.

11-21-2003, 04:23 PM	#7
rancid240 Post Whore! Join Date: Jan 2002 Location: Irvine CA Posts: 2,770 Trader Rating: (72) Feedback Score: 72 reviews	my question still remains unanswered The ssr rims have tires with air in them, Is this why the bolts wont budge? If so can I just take say my tire pressure gauge, let all the air out, and then swap the faces?