corbeau fx1/rail combo??? - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

AdrenalineS14 · 12-18-2011, 11:09 AM

Own an S14 need to know what rail will work for Corbeau FX1 seat not the "pro" or "wide" im 6'1" and want to find the lowest seat rail possible thanks!

punxva · 12-18-2011, 12:14 PM

i had a forza and ran a corbeau rail/slider it kinda sucked since it's bottom mount so you really can't get it to sit real low. I ideally wanted to run bride mo rails but i ended up just getting a Zeta 3 and buddy club rails. If you want it low go with either custom, bride, or switch to a side mount seat. Hope this helped

AdrenalineS14 · 12-18-2011, 12:29 PM

Quote:

Originally Posted by punxva

i had a forza and ran a corbeau rail/slider it kinda sucked since it's bottom mount so you really can't get it to sit real low. I ideally wanted to run bride mo rails but i ended up just getting a Zeta 3 and buddy club rails. If you want it low go with either custom, bride, or switch to a side mount seat. Hope this helped

Corbeau FX1 seats are side mount fixed bucket seats, i appreciate your input though

*TheRealSy90* · 12-18-2011, 03:40 PM

Nagisa / NAMS Auto rails. My FX1 touches the floor.

AdrenalineS14 · 12-18-2011, 04:06 PM

Quote:

Originally Posted by TheRealSy90

Nagisa / NAMS Auto rails. My FX1 touches the floor.

Ohhhh ok like barely touching the floor? and do you fit with a helmet on?

moco · 02-07-2012, 12:09 PM

Quote:

Originally Posted by TheRealSy90

Nagisa / NAMS Auto rails. My FX1 touches the floor.

what fx1 seat do you have? i just got a fx1(wide) do you think that set would work with this seat?

A DUDE · 01-13-2014, 12:09 AM

Quote:

Originally Posted by TheRealSy90

Nagisa / NAMS Auto rails. My FX1 touches the floor.

I know this is very old, but in the same situation.

Just wanted to clarify if you have/had the FX1 (not pro or wide) and the Nagisa auto rails side mounts fit fine?

Thanks hope to hear from you

*TheRealSy90* · 01-13-2014, 01:47 AM

Quote:

Originally Posted by A DUDE

I know this is very old, but in the same situation.

Just wanted to clarify if you have/had the FX1 (not pro or wide) and the Nagisa auto rails side mounts fit fine?

Thanks hope to hear from you

Yes. I'm still running both. I flipped the rear brackets upside down Andy seat touches the floor it's low as shit.

Sent from my iPhone using Tapatalk

di-devol · 01-13-2014, 09:35 AM

It touches the floor because it has bottom mount mounting options as well. The 4 mounting locations on the bottom have a "raised" portion that hits the floor.

*TheRealSy90* · 01-20-2014, 10:18 PM

Quote:

Originally Posted by di-devol

It touches the floor because it has bottom mount mounting options as well. The 4 mounting locations on the bottom have a "raised" portion that hits the floor.

That's true, but it's still really low. I thought about cutting off those raised mounts on the bottom of the seat but I wasn't sure if it would jeopardize the strength of the seat bottom.

Sent from my iPhone using Tapatalk

A DUDE · 01-23-2014, 10:47 PM

Quote:

Originally Posted by TheRealSy90

Yes. I'm still running both. I flipped the rear brackets upside down Andy seat touches the floor it's low as shit.

Sent from my iPhone using Tapatalk

dude i just bought these Nagisa XNSR011LD 011LD Bucket Seat Rail (Dual Lock) Silvia S13 S14 S15

they don't fit on my FX1! what's going on?!

Also I don't understand how they're supposed to be mounted side or bottom. The mount points aren't threaded inside or out!

slydin240sx · 02-07-2012, 12:36 PM

Do not get Buddy Club seat rails. They suck and don't sit low at all....
I would get Nagisa rails. Those bishes go LOW!

moco · 02-07-2012, 12:53 PM

^thanks for the info. whats your seat set up?

slydin240sx · 02-07-2012, 01:24 PM

I bought a fixed back bucket seat from a local guy here. The seat is a non name brand fixed back bucket seat imported from Japan through a local importer of JDM goodies. Pretty much a cheap bucket seat and not FIA approved. I then bought a brand new Buddy Club rail to mount the seat in my s14. IMO the aftermarket seat felt like it sat higher than my stock s14 seats. I had in there about 12 hours before I removed it and put my stock seat back in. I DD my s14 so I can't sit in a upright position for extended periods of time. I need to lean some. I also didn't feel that the seat would have held up well if I had been in a accident.
Here's a picture of the setup when I had it installed.

*TheRealSy90* · 01-24-2014, 10:32 PM

Idk about that rail, this is the one I have.

http://www.frsport.com/Nagisa-XNSR01...SX_p_3003.html

The one you got wouldn't be able to go as low or have as much adjustability. The seats side mounts should be threaded not the rail itself.

Sent from my iPhone using Tapatalk

A DUDE · 01-27-2014, 12:29 PM

Quote:

Originally Posted by TheRealSy90

Idk about that rail, this is the one I have.

Nagisa XNSR011L R011L Sidemount Ultra Low Seat Rail Driver Side 240SX

The one you got wouldn't be able to go as low or have as much adjustability. The seats side mounts should be threaded not the rail itself.

Sent from my iPhone using Tapatalk

arggggggg fml thanks

12-18-2011, 11:09 AM	#1
AdrenalineS14 Zilvia Member Join Date: Mar 2011 Location: Tucson, AZ Age: 35 Posts: 202 Trader Rating: (1) Feedback Score: 1 reviews	corbeau fx1/rail combo??? Own an S14 need to know what rail will work for Corbeau FX1 seat not the "pro" or "wide" im 6'1" and want to find the lowest seat rail possible thanks!

01-13-2014, 09:35 AM	#9
di-devol Zilvia FREAK! Join Date: Jun 2010 Location: Woodinville Age: 39 Posts: 1,412 Trader Rating: (5) Feedback Score: 5 reviews	It touches the floor because it has bottom mount mounting options as well. The 4 mounting locations on the bottom have a "raised" portion that hits the floor. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

02-07-2012, 12:36 PM	#12
slydin240sx Zilvia Addict Join Date: Apr 2009 Location: Missouri Posts: 919 Trader Rating: (3) Feedback Score: 3 reviews	Do not get Buddy Club seat rails. They suck and don't sit low at all.... I would get Nagisa rails. Those bishes go LOW!

02-07-2012, 12:53 PM	#13
moco Zilvia Member Join Date: Sep 2011 Location: los angeles Posts: 247 Trader Rating: (3) Feedback Score: 3 reviews	^thanks for the info. whats your seat set up?

02-07-2012, 01:24 PM	#14
slydin240sx Zilvia Addict Join Date: Apr 2009 Location: Missouri Posts: 919 Trader Rating: (3) Feedback Score: 3 reviews	I bought a fixed back bucket seat from a local guy here. The seat is a non name brand fixed back bucket seat imported from Japan through a local importer of JDM goodies. Pretty much a cheap bucket seat and not FIA approved. I then bought a brand new Buddy Club rail to mount the seat in my s14. IMO the aftermarket seat felt like it sat higher than my stock s14 seats. I had in there about 12 hours before I removed it and put my stock seat back in. I DD my s14 so I can't sit in a upright position for extended periods of time. I need to lean some. I also didn't feel that the seat would have held up well if I had been in a accident. Here's a picture of the setup when I had it installed.