Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 07-24-2019, 01:10 PM   #1
CallMeKev
 
Join Date: Apr 2013
Location: Texas
Age: 27
Posts: 29
Trader Rating: (0)
CallMeKev is an unknown quantity at this point
Feedback Score: 0 reviews
Removed dash now alternator not working?

I was removing my dash to replace a couple Ac blend door actuators, all went well got them working. But before putting the dash back on I wanted to keep the car running while switching them back and forth between vents. Testing it before putting the dash back on basically but the car stalled soon after and battery was dead wouldn’t start it back up. Placed battery on a charger, came back at it later when it was fully charged. All good starts up fine so I checked voltage. Reading 11.98v w/ the car running, 12.6v with the car off, so battery is good. Check the voltage off the alternator and nothing, it’s reading the 11.98v when the car is running. My assumption was that I had my alternator gave out. (Ka24de w/Quest alt) , so I go into my parts bin grab a known working alt. (Downgraded back to stock w/ bracket) installed, but still not charging. Went to autozone got the quest alt tested and it was fine. So alternator doesn’t seem to be the issue? I’m leading towards the plug next, am I suppose to see constant voltage at 1 of the 2 pins or what? Etc? That’s the info I’m here to ask for, what’s next for me to check. (Note: I did check alternator fuse, even switched it with another one seems fine. Also took a look at all the other fuses. Also my cluster is plugged in, at first it wasn’t when it first died on me but problem still there. )
CallMeKev is offline   Reply With Quote
Sponsored Links
Old 07-24-2019, 04:48 PM   #2
dbeiler
Premium Member
 
dbeiler's Avatar
 
Join Date: Jun 2012
Location: Lancaster county, PA
Age: 30
Posts: 465
Trader Rating: (4)
dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler
Feedback Score: 4 reviews
Is the charge warning lamp on the gauge cluster staying on when the car is running? Does it light at all?

The back side of the gauge cluster has uninsulated solder joints. They can short out against the vehicle frame if you're moving the cluster around with ignition turned on. Those circuits are mostly protected by a small fuse (7.5amp on an S14).

What model vehicle are you working on?
dbeiler is offline   Reply With Quote
Old 07-24-2019, 10:25 PM   #3
CallMeKev
 
Join Date: Apr 2013
Location: Texas
Age: 27
Posts: 29
Trader Rating: (0)
CallMeKev is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by dbeiler View Post
Is the charge warning lamp on the gauge cluster staying on when the car is running? Does it light at all?

The back side of the gauge cluster has uninsulated solder joints. They can short out against the vehicle frame if you're moving the cluster around with ignition turned on. Those circuits are mostly protected by a small fuse (7.5amp on an S14).

What model vehicle are you working on?
I’ll check in the morning if the warning lamp even lights up I didn’t bother to check or even notice. And you’re right, I’ve been having it leaned back against the frame there. Possibly did blow that fuse, yeap 95 s14. Is that on the inside or outside fuse box that you’re referring to?
CallMeKev is offline   Reply With Quote
Old 07-25-2019, 11:16 AM   #4
CallMeKev
 
Join Date: Apr 2013
Location: Texas
Age: 27
Posts: 29
Trader Rating: (0)
CallMeKev is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by CallMeKev View Post
I’ll check in the morning if the warning lamp even lights up I didn’t bother to check or even notice. And you’re right, I’ve been having it leaned back against the frame there. Possibly did blow that fuse, yeap 95 s14. Is that on the inside or outside fuse box that you’re referring to?
Update all the fuses seem fine including the 7.5 ones. I do not see the warning lamp light up when the car is on. What could I check next?
CallMeKev is offline   Reply With Quote
Old 07-26-2019, 07:55 AM   #5
CallMeKev
 
Join Date: Apr 2013
Location: Texas
Age: 27
Posts: 29
Trader Rating: (0)
CallMeKev is an unknown quantity at this point
Feedback Score: 0 reviews
Anybody else ?
CallMeKev is offline   Reply With Quote
Old 07-26-2019, 08:04 PM   #6
dbeiler
Premium Member
 
dbeiler's Avatar
 
Join Date: Jun 2012
Location: Lancaster county, PA
Age: 30
Posts: 465
Trader Rating: (4)
dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler
Feedback Score: 4 reviews
The charge indicator bulb is powered by an underdash fusebox fuse. The bulb is grounded by the alternator.

Disconnect the alternator 4-pin connector. Turn ignition key on; engine not running. Voltage test pin 3 of the connector. It is a white/red wire according to my '95 service manual. You should get battery voltage. If you have no voltage; check for open wiring from fuse to bulb to alternator. Check for a blown bulb in the charge warning lamp gauge.

If you have battery voltage, check for a faulty alternator ground wire.

Normally you can bypass the charge warning circuit by simply revving the engine up above 2500rpm. This will be sufficient to energize the alternator field coil and the alternator should continue to charge until the engine is shut down.
dbeiler is offline   Reply With Quote
Old 07-26-2019, 08:08 PM   #7
dbeiler
Premium Member
 
dbeiler's Avatar
 
Join Date: Jun 2012
Location: Lancaster county, PA
Age: 30
Posts: 465
Trader Rating: (4)
dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler
Feedback Score: 4 reviews
Oops. It's not a 4-pin connector. It's a 2-pin. White/red wire is the one you want.

The three wires (other than the fourth ground wire) should all have battery voltage when the ignition is turned on.
dbeiler is offline   Reply With Quote
Old 08-02-2019, 08:41 AM   #8
CallMeKev
 
Join Date: Apr 2013
Location: Texas
Age: 27
Posts: 29
Trader Rating: (0)
CallMeKev is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by dbeiler View Post
The charge indicator bulb is powered by an underdash fusebox fuse. The bulb is grounded by the alternator.

Disconnect the alternator 4-pin connector. Turn ignition key on; engine not running. Voltage test pin 3 of the connector. It is a white/red wire according to my '95 service manual. You should get battery voltage. If you have no voltage; check for open wiring from fuse to bulb to alternator. Check for a blown bulb in the charge warning lamp gauge.

If you have battery voltage, check for a faulty alternator ground wire.

Normally you can bypass the charge warning circuit by simply revving the engine up above 2500rpm. This will be sufficient to energize the alternator field coil and the alternator should continue to charge until the engine is shut down.
ok update been busy so not much progress. With ignition key ON I am getting 12.10v at the alt output, 12.10v at the first pin on the plug, the other (white/red) is getting voltage too but its 11.95v, when I turn the ignition off the 11.95v goes to 0 while the other 2 stay at constant resting battery voltage around 12.4-5ish, seems normal right? also checked fuses again this time checking their continuity to make sure I wasn't missing a blown one but nothing all good. Charge light lamp does not illuminate when I start the car or ever period, thats my only good lead at this point that charge light lamp, I've tried other known working bulbs but ill buy some news ones to eliminate the possibility of blown bulb... any other ideas? Thinking off adding an extra ground just to cancel grounding an issue but idk
CallMeKev is offline   Reply With Quote
Old 08-02-2019, 09:08 AM   #9
brndck
Premium Member
 
brndck's Avatar
 
Join Date: Jun 2003
Location: torrance, ca
Age: 39
Posts: 12,407
Trader Rating: (129)
brndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfection
Feedback Score: 129 reviews
Send a message via AIM to brndck
12v is low. alternator should be outputting close to 14v.
when you had the alternator tested was it able to output 14v under load?
__________________

http://outslidersandsmokeproduce.blogspot.com/
Quote:
Originally Posted by Mannykiller View Post
it'll fit JANK.. and no one likes Jank except Broke ass zilvians.
brndck is offline   Reply With Quote
Old 08-02-2019, 03:05 PM   #10
dbeiler
Premium Member
 
dbeiler's Avatar
 
Join Date: Jun 2012
Location: Lancaster county, PA
Age: 30
Posts: 465
Trader Rating: (4)
dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler
Feedback Score: 4 reviews
Your voltage checks are all normal. This leaves you with a faulty alternator or ground.

The alternator is responsible for grounding the bulb circuit. You can do a quick bulb test by bypassing the alt. Disconnect the two pin connector from the alt and use a short piece of wire to hotwire the white/red wire straight to chassis ground. The charge warning bulb should illuminate nice and bright whenever the key is turned ON.

Test the alt ground wire or temporarily replace it.

If an alternator has extremely underdriven pulleys on it; it won't spin fast enough to charge at idle.
dbeiler is offline   Reply With Quote
Old 08-02-2019, 03:06 PM   #11
dbeiler
Premium Member
 
dbeiler's Avatar
 
Join Date: Jun 2012
Location: Lancaster county, PA
Age: 30
Posts: 465
Trader Rating: (4)
dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler dbeiler
Feedback Score: 4 reviews
Quote:
Originally Posted by brndck View Post
12v is low. alternator should be outputting close to 14v.
when you had the alternator tested was it able to output 14v under load?
He's doing Key ON, engine OFF voltage checks.
dbeiler is offline   Reply With Quote
Old 08-02-2019, 03:11 PM   #12
brndck
Premium Member
 
brndck's Avatar
 
Join Date: Jun 2003
Location: torrance, ca
Age: 39
Posts: 12,407
Trader Rating: (129)
brndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfectionbrndck is close to perfection
Feedback Score: 129 reviews
Send a message via AIM to brndck
Quote:
Originally Posted by dbeiler View Post
He's doing Key ON, engine OFF voltage checks.
ah gotcha. with engine off 12v is def normal.
__________________

http://outslidersandsmokeproduce.blogspot.com/
Quote:
Originally Posted by Mannykiller View Post
it'll fit JANK.. and no one likes Jank except Broke ass zilvians.
brndck is offline   Reply With Quote
Reply

Bookmarks

Tags
alternator not charging


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 12:00 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™